EXHAUST GAS TEMPERATURE SENSOR(w/ Glow Plug Controller) INSTALLATION

PROCEDURE

  1. INSTALL NO. 2 EXHAUST GAS TEMPERATURE SENSOR

    Note:

    If the No. 2 exhaust gas temperature sensor is dropped, replace it with a new one.

    1. A357457C01

      *a

      Torque Wrench Fulcrum Length

      Using a 14 mm union nut wrench, install the No. 2 exhaust gas temperature sensor to the No. 2 exhaust manifold.

      Specified tightening torque

      30 N*m

      306 kgf*cm

      22 ft.*lbf

      Tip:
      • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

        Click hereClick here

      • When using a 14 mm union nut wrench (fulcrum length of 25 mm (0.984 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 26 N*m (265 kgf*cm, 19 ft.*lbf)

  2. INSTALL NO. 2 EXHAUST MANIFOLD

  3. INSTALL DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY

  4. INSTALL NO. 4 MANIFOLD SUPPORT BRACKET

  5. INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

  6. INSTALL NO. 5 MANIFOLD SUPPORT BRACKET

  7. INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR

  8. INSTALL FRONT EXHAUST PIPE ASSEMBLY

  9. INSTALL FRONT CENTER FLOOR BRACE SUB-ASSEMBLY

  10. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

  11. INSTALL NO. 1 TURBO INSULATOR

  12. INSTALL NO. 1 AIR TUBE

  13. INSTALL AIR CLEANER CASE SUB-ASSEMBLY

  14. INSTALL AIR CLEANER CAP SUB-ASSEMBLY

  15. INSTALL BATTERY

  16. INSTALL NO. 2 HOSE TO HOSE TUBE (for LHD)

  17. INSTALL NO. 2 HOSE TO HOSE TUBE (for RHD)

  18. INSTALL NO. 2 ENGINE COVER BRACKET

  19. INSTALL SENSOR BRACKET

  20. INSTALL DIFFERENTIAL PRESSURE SENSOR ASSEMBLY

  21. INSTALL EXHAUST GAS TEMPERATURE SENSOR

    Note:

    If the exhaust gas temperature sensor is dropped, replace it with a new one.

    1. A359382C02

      *a

      Torque Wrench Fulcrum Length

      Using a 14 mm union nut wrench, install the exhaust gas temperature sensor to the No. 2 exhaust manifold.

      Specified tightening torque

      30 N*m

      306 kgf*cm

      22 ft.*lbf

      Tip:
      • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

        Click hereClick here

      • When using a 14 mm union nut wrench (fulcrum length of 25 mm (0.984 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 26 N*m (265 kgf*cm, 19 ft.*lbf)

    2. Engage the clamp to connect the wire harness to the wire harness clamp bracket.

    3. Engage the claw to connect the exhaust gas temperature sensor connector to the wire harness clamp bracket.

    4. Install the wire harness clamp bracket to the timing chain cover assembly with the bolt.

      9.0 N*m

      92 kgf*cm

      80 in.*lbf

    5. Connect the exhaust gas temperature sensor connector.

  22. INSTALL WIRE HARNESS CLAMP BRACKET

  23. INSTALL NO. 1 WIRE HARNESS HEAT INSULATOR

  24. INSTALL OUTER COWL TOP PANEL

  25. INSTALL NO. 2 HEATER AIR DUCT SPLASH SHIELD SEAL

  26. INSTALL WATER GUARD PLATE LH

  27. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

  28. INSTALL NO. 1 ENGINE COVER (w/ No. 1 Engine Cover)

  29. LEARNING DIFFERENTIAL PRESSURE SENSOR ASSEMBLY

  30. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click hereClick hereClick hereClick here

  31. INSPECT FOR EXHAUST GAS LEAK