ECD SYSTEM(w/o Glow Plug Controller) TERMINALS OF ECM

A157743E20
Tip:

The standard voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated.

The result of the checks should be compared with the standard voltage for that pair of terminals, which is displayed in the Specified Condition column.

The illustration above can be used as a reference to identify the ECM terminal locations.

Terminal No. (Symbol)

Wiring Color

Terminal Description

Condition

Specified Condition

A101-1 (+B) - A101-2 (E1)

B - W-B

Power source of ECM

Ignition switch ON

11 to 14 V

A101-61 (+B2) - A101-2 (E1)

B - W-B

Power source of ECM

Ignition switch ON

11 to 14 V

A101-23 (BATT) - A101-2 (E1)

W - W-B

Battery (for measuring the battery voltage and for the ECM memory)

Always

11 to 14 V

A101-7 (IGSW) - A101-2 (E1)

B - W-B

Ignition switch

Ignition switch ON

11 to 14 V

A101-22 (MREL) - A101-2 (E1)

B - W-B

EFI-MAIN relay

Ignition switch ON

11 to 14 V

20 seconds elapsed since ignition switch off

0 to 1.5 V

B138-13 (GREL) - A101-2 (E1)

B - W-B

Glow plug relay assembly

Ignition switch ON at cold engine

0 to 1.5 V

Idling with warm engine

11 to 14 V

A101-55 (VPA) - A101-57 (EPA)

W - Y

Accelerator pedal position sensor (for engine control)

Ignition switch ON, accelerator pedal fully released

0.5 to 1.1 V

Ignition switch ON, accelerator pedal fully depressed

2.6 to 4.5 V

A101-52 (VPA2) - A101-54 (EPA2)

R - P

Accelerator pedal position sensor (for sensor malfunction detection)

Ignition switch ON, accelerator pedal fully released

1.2 to 2.0 V

Ignition switch ON, accelerator pedal fully depressed

3.4 to 4.75 V

A101-56 (VCPA) - A101-57 (EPA)

B - Y

Power source of accelerator pedal position sensor (for VPA)

Ignition switch ON

4.5 to 5.5 V

A101-53 (VCP2) - A101-54 (EPA2)

L - P

Power source of accelerator pedal position sensor (for VPA2)

Ignition switch ON

4.5 to 5.5 V

A101-46 (VCTA) - A101-47 (ETA)

V - P

Power source of diesel throttle position sensor

Ignition switch ON

4.5 to 5.5 V

A101-45 (VTA1) - A101-47 (ETA)

LG - P

Diesel throttle position sensor

Throttle valve fully opened

3.2 to 4.9 V

Throttle valve fully closed

0.5 to 1.1 V

A101-43 (M+) - A101-2 (E1)

W - W-B

Diesel throttle duty signal

Engine racing

Pulse generation

A101-42 (M-) - A101-2 (E1)

R - W-B

Diesel throttle duty signal

Engine racing

Pulse generation

A101-63 (H-) - A101-2 (E1)

L - W-B

Air fuel ratio sensor heater

Ignition switch ON

11 to 14 V

Idling

Pulse generation

(See waveform 1)

A101-69 (AF1+) - A101-2 (E1)

L - W-B

Air fuel ratio sensor signal

Ignition switch ON

1.5 to 4.9 V

A101-70 (AF1-) - A101-2 (E1)

R - W-B

Air fuel ratio sensor signal

Ignition switch ON

2.35 to 2.65 V

A101-68 (TR) - A101-2 (E1)

P - W-B

Air fuel ratio sensor signal

Ignition switch ON

1.5 to 4.9 V

A101-71 (RE) - A101-2 (E1)

G - W-B

Air fuel ratio sensor signal

Ignition switch ON

2.1 to 3.5 V

B138-29 (THF) - B138-28 (ETHF)

GR - BR

Fuel temperature sensor

Idling

0.5 to 2.0 V

B138-15 (VCS) - B138-14 (E2S)

R - G

Power source of fuel pressure sensor

Ignition switch ON

4.5 to 5.5 V

B138-16 (PC) - B138-14 (E2S)

W - G

Fuel pressure sensor

(common rail pressure sensor)

Idling

1.0 to 1.3 V

A101-11 (VG) - A101-12 (EVG)

LG - BR

Mass air flow meter

Idling

Pulse generation

A101-30 (THA) - A101-31 (ETHA)

L - BR

Intake air temperature sensor

Idling, intake air temperature 20°C (68°F)

0.5 to 2.0 V

B138-4 (PRV) - A101-2 (E1)

W - W-B

Pressure control valve signal

Drive vehicle at 50 km/h (31 mph) in third gear, and then decelerate by releasing accelerator pedal

Pulse generation

(See waveform 2)

B138-12 (PCV) - A101-2 (E1)

L - W-B

Supply pump

(suction control valve)

Idling

Pulse generation

(See waveform 3)

B138-1 (IJ1+) - B138-21 (IJ1-)

W - B

Injector

Idling

Pulse generation

B138-2 (IJ2+) - B138-30 (IJ2-)

R - W

Injector

Idling

Pulse generation

B138-3 (IJ3+) - B138-31 (IJ3-)

W - R-B

Injector

Idling

Pulse generation

B138-20 (IJ4+) - B138-32 (IJ4-)

L - R-L

Injector

Idling

Pulse generation

A101-50 (THCI) - A101-51 (ETCI)

LG - L

Exhaust gas temperature sensor B1S1

Idling with warm engine

2.9 to 3.3 V

A101-48 (THCO) - A101-49 (ETCO)

GR - V

Exhaust gas temperature sensor B1S2

Idling with warm engine

2.9 to 3.3 V

B138-40 (THW) - B138-39 (ETHW)

B - BR

Engine coolant temperature sensor

Idling, engine coolant temperature 80°C (176°F)

0.2 to 1.0 V

B138-8 (THIA) - B138-7 (ETHI)

V - GR

Intake air temperature sensor (intake manifold)

Idling, intake air temperature 0 to 80 °C (32 to 176°F)

0.5 to 2.0 V

A101-14 (VPIM) - A101-15 (EPIM)

R - Y

Power source of diesel turbo pressure sensor

Ignition switch ON

4.75 to 5.25 V

A101-13 (PIM) - A101-15 (EPIM)

G - Y

Diesel turbo pressure sensor

Ignition switch ON

(same as atmosphere pressure)

0.8 to 1.4 V

B138-19 (NE+) - B138-18 (NE-)

R - G

Crankshaft position sensor

Idling

Pulse generation

(See waveform 4)

B138-11 (G+) - B138-10 (G-)

P - L

Camshaft position sensor

Idling

Pulse generation

(See waveform 9)

B138-37 (VNVC) - B138-36 (VNE2)

W -B

Power source of nozzle vane position sensor

Ignition switch ON

4.5 to 5.5 V

B138-38 (VTAI) - B138-36 (VNE2)

R -B

Nozzle vane position sensor

VN turbocharger fully closed

0.9 to 2.1 V

VN turbocharger fully opened

3.0 to 4.1 V

B138-34 (M+) - A101-2 (E1)

BR - W-B

VN turbocharger motor

Idling with warm engine

Pulse generation

B138-33 (M-) - A101-2 (E1)

Y - W-B

VN turbocharger motor

Idling with warm engine

Pulse generation

A101-40 (ECBV) - A101-2 (E1)

Y - W-B

VSV for EGR cooler bypass valve

Ignition switch ON with cold engine

0 to 1.5 V

Idling with warm engine

11 to 14 V

B138-26 (VCEG) - B138-25 (EEGL)

W - B

Power source of EGR valve position sensor

Ignition switch ON

4.5 to 5.5 V

B138-23 (EGM+) - A101-2 (E1)

W - W-B

EGR valve motor

Idling with warm engine

Pulse generation

B138-22 (EGM-) - A101-2 (E1)

R - W-B

EGR valve motor

Idling with warm engine

Pulse generation

B138-27 (EGLS) - B138-25 (EEGL)

G - B

EGR valve position sensor

EGR valve fully closed

0.8 to 1.6 V

EGR valve fully opened

3.6 to 4.4 V

A101-33 (VCPX) - A101-34 (EPEX)

R - G

Power source of differential pressure sensor

Ignition switch ON

4.5 to 5.5 V

A101-32 (PEX) - A101-34 (EPEX)

P - G

Differential pressure sensor

Ignition switch ON

0.5 to 1.0 V

A101-5 (D)*1 - A101-2 (E1)

GR - W-B

No. 2 clutch pedal switch assembly

Ignition switch ON, clutch pedal released

11 to 14 V

Ignition switch ON, clutch pedal depressed

0 to 1.5 V

A101-8 (OILH) - A101-2 (E1)

R - W-B

Engine oil level upper switch

Oil level upper switch off

4.5 to 5.0 V

Oil level upper switch ON

0 to 1.5 V

A101-6 (STA) - A101-2 (E1)

LG - W-B

Starter signal

Cranking

6.0 V or higher

A101-80 (TACH) - A101-2 (E1)

GR - W-B

Engine speed

Idling

Pulse generation

A101-29 (STP) - A101-2 (E1)

LG - W-B

Stop light switch

Brake pedal depressed

7.5 to 14 V

Brake pedal released

0 to 1.5 V

A101-28 (ST1-) - A101-2 (E1)

R - W-B

Stop light switch

(opposite to STP)

Brake pedal depressed

0 to 1.5 V

Brake pedal released

7.5 to 14 V

A101-25 (SPD) - A101-2 (E1)

V - W-B

Speed signal from combination meter

Ignition switch ON, driving wheel rotating slowly

Pulse generation

(See waveform 5)

A101-37 (W) - A101-2 (E1)

LG - W-B

MIL

MIL illuminated

0 to 3 V

MIL not illuminated

11 to 14 V

A101-24 (TC) - A101-2 (E1)

P - W-B

Terminal TC of DLC3

Ignition switch ON

11 to 14 V

A101-19 (RFC) - A101-2 (E1)

R - W-B

Cooling fan control

Ignition switch ON, A/C switch on (Max cool)

Pulse generation

(See waveform 10)

A101-27 (ELS2) - A101-2 (E1)

L - W-B

Electric load

Defogger switch ON

7.5 to 14 V

Defogger switch off

0 to 1.5 V

A101-26 (MHSW)*2 - A101-2 (E1)

R - W-B

Power heater switch signal

Power heater switch ON

11 to 14 V

A101-9 (R)*1 - A101-2 (E1)

R - W-B

Back-up light switch signal

Back-up light switch ON

11 to 14 V

A101-3 (CANH) - A101-2 (E1)

B - W-B

CAN communication line

Ignition switch ON

Pulse generation

(See waveform 6)

A101-4 (CANL) - A101-2 (E1)

W - W-B

CAN communication line

Ignition switch ON

Pulse generation

(See waveform 7)

A101-17 (CANP) - A101-2 (E1)

B - W-B

CAN communication line

Ignition switch ON

Pulse generation

(See waveform 6)

A101-16 (CANN) - A101-2 (E1)

SB - W-B

CAN communication line

Ignition switch ON

Pulse generation

(See waveform 7)

A101-73 (POP) - A101-41 (E2)

LG - W-B

Oil pressure sender gauge assembly

Engine running

0.34 to 4.66 V

A101-79 (NEO) - A101-2 (E1)

L - W-B

Engine speed

Idling

Pulse generation

(See waveform 8)

A101-74 (VC) - A101-75 (E2)

B - W

Power source of oil pressure sender gauge assembly

Ignition switch ON

4.75 to 5.25 V

B138-5 (V20) - A101-2 (E1)

R - W-B

Oil pressure switching valve assembly

Oil pressure switching valve ON

0 to 1.5 V

Oil pressure switching valve OFF

11 to 14 V

B138-9 (SG1) - Body ground

BR - -

Shielded earth (ground) circuit of camshaft position sensor

Always

Below 1 Ω

A101-72 (SAF1) - Body ground

BR - -

Shielded earth (ground) circuit of air fuel ratio sensor

Always

Below 1 Ω

A101-67 (SAF2) - Body ground

BR - -

Shielded earth (ground) circuit of air fuel ratio sensor

Always

Below 1 Ω

B138-35 (GND) - Body ground

BR - -

Shielded earth (ground) circuit of DC motor

Always

Below 1 Ω

B138-24 (SEG) - Body ground

BR - -

Shielded earth (ground) circuit of EGR motor

Always

Below 1 Ω

B138-17 (SNE) - Body ground

BR - -

Shielded earth (ground) circuit of crankshaft position sensor

Always

Below 1 Ω

A101-44 (GE01) - Body ground

BR - -

Shielded earth (ground) circuit of throttle actuator

Always

Below 1 Ω

A101-2 (E1) - Body ground

W-B - -

Ground

Always

Below 1 Ω

A101-41 (E2) - Body ground

W-B - -

Ground

Always

Below 1 Ω

A101-62 (E3) - Body ground

W-B - -

Ground

Always

Below 1 Ω

*1: for Manual transaxle models

*2: w/ Combination type power heater

  1. Waveform 1

    A208563E05
    Table 1. Air Fuel Ratio Sensor Heater Signal

    ECM Terminal Name

    H- and E1

    Tester Range

    5 V/DIV, 2 ms/DIV

    Condition

    Idling

    Tip:

    The wavelength varies depending on the engine operating conditions.

  2. Waveform 2

    A115980E08
    Table 2. Pressure Control Valve Signal

    ECM Terminal Name

    PRV and E1

    Tester Range

    10 V/DIV, 0.5 ms/DIV

    Condition

    Drive vehicle at 50 km/h (31 mph) in third gear, and then decelerate by releasing accelerator pedal

    Tip:

    The waveform varies depending on the pressure control valve operation.

  3. Waveform 3

    A294242E01
    Table 3. Suction Control Valve Signal

    ECM Terminal Name

    PCV and E1

    Tester Range

    10 V/DIV, 5 ms/DIV

    Condition

    Idling

    Tip:

    The waveform varies depending on the suction control valve operation.

  4. Waveform 4

    A294243E01
    Table 4. Crankshaft Position Sensor Signal

    ECM Terminal Name

    NE+ and NE-

    Tester Range

    5 V/DIV, 10 ms/DIV

    Condition

    Idling

    Tip:

    The waveform varies depending on the engine speed.

  5. Waveform 5

    A286063E02
    Table 5. Vehicle Speed Signal

    ECM Terminal Name

    SPD and E1

    Tester Range

    1 V/DIV, 10 ms/DIV

    Condition

    Ignition switch ON, driving wheel rotating slowly

    Tip:

    The wavelength becomes shorter as the vehicle speed increases.

  6. Waveform 6

    A129236E07
    Table 6. CAN Communication Signal (Reference)

    ECM Terminal Name

    CANH and E1

    CANP and E1

    Tester Range

    1 V/DIV, 10 μs/DIV

    Condition

    Ignition switch ON

    Tip:

    The wavelength becomes shorter depending on the CAN communication signal.

  7. Waveform 7

    Table 7. CAN Communication Signal (Reference)

    ECM Terminal Name

    CANL and E1

    CANN and E1

    Tester Range

    1 V/DIV, 10 μs/DIV

    Condition

    Ignition switch ON

    Tip:

    The wavelength becomes shorter depending on the CAN communication signal.

    A129237E06
  8. Waveform 8

    A294256E01
    Table 8. Engine Speed Signal

    ECM Terminal Name

    NEO and E1

    Tester Range

    5 V/DIV, 1 ms/DIV

    Condition

    Idling

    Tip:

    The waveform varies depending on the crankshaft position sensor signal.

  9. Waveform 9

    A294244E01
    Table 9. Camshaft Position Sensor Signal

    ECM Terminal Name

    G+ and G-

    Tester Range

    5 V/DIV, 10 ms/DIV

    Condition

    Idling

    Tip:

    The waveform varies depending on the engine speed.

  10. Waveform 10

    A247290E04
    Table 10. Cooling Fan Control Signal

    ECM Terminal Name

    RFC and E1

    Tester Range

    1 V/DIV, 4 ms/DIV

    Condition

    Ignition switch ON, A/C switch on (Max cool)

    Tip:

    The duty ratio varies depending on the engine coolant temperature.