STOP AND START SYSTEM TERMINALS OF ECU

  1. ENGINE STOP AND START ECU

    A354020N01
    1. Disconnect the A8, A9 and E24 engine stop and start ECU connector.

    2. Measure the resistance and voltage according to the value(s) in the table below.

      Terminal No. (Symbol)

      Wiring Color

      Terminal Description

      Condition

      Specified Condition

      A8-5 (+B) - Body ground

      B - Body ground

      Power source of engine stop and start ECU

      Ignition switch ON

      9.5 to 14 V

      A8-7 (BIN) - Body ground

      L - Body ground

      Battery

      Always

      9.5 to 14 V

      A8-8 (GND) - Body ground

      W-B - Body ground

      Ground

      Always

      Below 1 Ω

      A9-10 (NE) - Body ground

      L - Body ground

      Engine speed signal from ECM

      Always

      10 kΩ or higher

      A9-17 (VB-) - Body ground

      W-B - Body ground

      Ground

      Always

      Below 1 Ω

      E24-15 (CANH) - Body ground

      P - Body ground

      CAN communication

      Always

      200 Ω or higher

      E24-16 (CANL) - Body ground

      W - Body ground

      CAN communication

      Always

      200 Ω or higher

      E24-17 (IG1) - Body ground

      L - Body ground

      Ignition switch signal

      Ignition switch ON

      9.5 to 14 V

      E24-19 (ACC) - Body ground

      GR - Body ground

      Ignition switch signal

      Ignition switch ACC

      9.5 to 14 V

      E24-20 (IG2) - Body ground

      P - Body ground

      Ignition switch signal

      Ignition switch ON

      9.5 to 14 V

    3. Reconnect the A8, A9 and E24 engine stop and start ECU connector.

    4. Measure the resistance and voltage according to the value(s) in the table below.

      Terminal No. (Symbol)

      Wiring Color

      Terminal Description

      Condition

      Specified Condition

      A8-6 (OPO) - A8-8 (GND)*1

      B - W-B

      Oil pump with motor assembly drive power source signal

      Either of the following conditions is met:

      • Engine stopped by stop and start control

      • Ignition switch ON (engine not running) and Active Test "AT Oil Pump (Lo)" being performed

      10.5 to 16 V

      A9-3 (BRE2) - Body ground

      G - Body ground

      Ground (vacuum sensor assembly (brake booster pressure sensor))

      Always

      Below 1 Ω

      A9-7 (BNT1) - A8-8 (GND)

      R - W-B

      Engine hood courtesy switch (hood lock assembly) signal

      • Ignition switch ON

      • Engine stopped

      • Engine hood closed

      0 to 1.5 V

      • Ignition switch ON

      • Engine stopped

      • Engine hood open

      8 to 14 V

      A9-9 (OPM1) - A8-8 (GND)*1

      P - W-B

      Oil pump with motor assembly directions signal

      Either of the following conditions is met:

      • Engine stopped by stop and start control

      • Ignition switch ON (engine not running) and Active Test "AT Oil Pump (Lo)" being performed

      Pulse generation

      (see waveform 1)

      A9-10 (NE) - A8-8 (GND)

      L - W-B

      Engine speed signal from ECM

      Idling after engine warmed up

      Pulse generation

      (see waveform 2)

      A9-11 (CLU) - A8-8 (GND)*2

      GR - W-B

      Clutch start switch assembly (for upper) signal

      • Ignition switch ON

      • Clutch pedal released

      8 to 14 V

      • Ignition switch ON

      • Clutch pedal fully depressed

      Below 1.5 V

      A9-13 (PB) - A9-3 (BRE2)

      B - G

      Vacuum sensor assembly (brake booster pressure sensor) signal

      • Ignition switch ON

      • Absolute pressure of 40 kPa 40 kPa (0.4 kgf/cm2, 5.8 psi) applied to vacuum sensor assembly (brake booster pressure sensor)

      1.6 to 2.0 V

      • Ignition switch ON

      • Absolute pressure of 60 kPa (0.6 kgf/cm2, 8.7 psi) applied to vacuum sensor assembly (brake booster pressure sensor)

      2.2 to 2.6 V

      • Ignition switch ON

      • Atmospheric pressure applied to vacuum sensor assembly (brake booster pressure sensor)

      3.4 to 3.8 V

      A9-14 (BRVC) - A8-8 (GND)

      P - W-B

      Vacuum sensor assembly (brake booster pressure sensor) power supply

      • Ignition switch ON

      • Engine stopped

      4.5 to 5.5 V

      A9-21 (STA) - A8-8 (GND)

      LG - W-B

      Starter operation signal

      Ignition switch ON

      0 V to 1.5 V

      Cranking

      6 V to 14 V

      A9-26 (TMVC) - A8-8 (GND)*2

      B - W-B

      Neutral position switch power supply

      • Ignition switch ON

      • Engine stopped

      4.5 to 5.5 V

      A9-27 (NOPM) - A8-8 (GND)*1

      GR - W-B

      Oil pump with motor assembly speed signal

      Either of the following conditions is met:

      • Engine stopped by stop and start control

      • Ignition switch ON (engine not running) and Active Test "AT Oil Pump (Lo)" being performed

      Pulse generation

      (see waveform 3)

      A9-27 (TMN) - A9-25 (TME2)*2

      R - GR

      Neutral position switch signal

      • Ignition switch ON

      • Shift lever in neutral

      2.7 to 4.3 V

      • Ignition switch ON

      • Shift lever in any other than neutral

      0.7 to 1.9 V

      A9-28 (CLL) - A8-8 (GND)

      W - W-B

      Park/neutral position switch signal*2

      • Ignition switch ON

      • Shift lever in any other than N or P

      8 to 14 V

      • Ignition switch ON

      • Shift lever in N or P

      Below 3.0 V

      Clutch start switch assembly (for lower) signal*3

      • Ignition switch ON

      • Clutch pedal released

      8 to 14 V

      • Ignition switch ON

      • Clutch pedal fully depressed

      Below 1.5 V

      E24-2 (BO1) - A8-8 (GND)

      SB - W-B

      Backup boost converter signal

      Always

      9.5 to 14 V

      E24-3 (ACO) - A8-8 (GND)

      GR - W-B

      Backup boost converter signal

      Ignition switch ACC

      9.5 to 14 V

      E24-4 (CHI) - A8-8 (GND)*3

      R - W-B

      Combustion type Power heater system operating signal

      • Ignition switch ON

      • Heater switch assembly on

      9.5 to 14 V

      • Ignition switch ON

      • Heater switch assembly off

      Below 1 V

      E24-11 (IGO2) - A8-8 (GND)

      P - W-B

      Backup boost converter signal

      Ignition switch ON

      9.5 to 14 V

      E24-12 (IGO1) - A8-8 (GND)

      L - W-B

      Backup boost converter signal

      Ignition switch ON

      9.5 to 14 V

      E24-17 (IG1) - A8-8 (GND)

      L - W-B

      Ignition switch signal

      Ignition switch ACC

      Below 1 V

      Ignition switch ON

      9.5 to 14 V

      E24-19 (ACC) - A8-8 (GND)

      GR - W-B

      Ignition switch signal

      Ignition switch off

      Below 1 V

      Ignition switch ACC

      9.5 to 14 V

      E24-20 (IG2) - A8-8 (GND)

      P - W-B

      Ignition switch signal

      Ignition switch ACC

      Below 1 V

      Ignition switch ON

      9.5 to 14 V

      E24-23 (ECAN) - A8-8 (GND)

      V - W-B

      Eco run cancel switch assembly signal

      • Ignition switch ON

      • Eco run cancel switch assembly pressed

      0 to 1.5 V

      • Ignition switch ON

      • Eco run cancel switch assembly not pressed

      8 to 14 V

      • *1: for CVT

      • *2: for Manual Transaxle

      • *3: w/ Combustion Type Power Heater System

    5. A329962E01

      Waveform 1

      Item

      Content

      Tester Connection

      A9-9 (OPM1) - A8-8 (GND)

      Tool Setting

      5 V/DIV., 5 ms./DIV.

      Condition

      Either of the following conditions is met:

      • Engine stopped by stop and start control

      • Ignition switch ON (engine not running) and Active Test "AT Oil Pump (Lo)" being performed

    6. A318633E03

      Waveform 2

      Table 1. Engine Speed Signal

      Item

      Content

      Tester Connection

      A9-10 (NE) - A8-8 (GND)

      Tool Setting

      5 V/DIV, 2 ms/DIV

      Condition

      Idling after engine warmed up

      Tip:

      The wavelength become shorter as the engine speed increases.

    7. A112562E03

      Waveform 3

      Item

      Content

      Tester Connection

      A9-27 (NOPM) - A8-8 (GND)

      Tool Setting

      5 V/DIV., 5 ms./DIV.

      Condition

      Either of the following conditions is met:

      • Engine stopped by stop and start control

      • Ignition switch ON (engine not running) and Active Test "AT Oil Pump (Lo)" being performed