FUEL TANK INSTALLATION
PROCEDURE
INSTALL NO. 1 CHARCOAL CANISTER OUTLET HOSE
Engage the 2 claws to install the No. 1 charcoal canister outlet hose to the fuel tank assembly.
Engage the clamp to connect the No. 1 charcoal canister outlet hose to the evaporation vent tube clamp.
INSTALL FUEL TANK MAIN TUBE SUB-ASSEMBLY
Engage the 2 claws to install the fuel tank main tube sub-assembly to the fuel tank assembly.
INSTALL NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY
Engage the 2 claws to install the No. 1 fuel evaporation tube sub-assembly to the fuel tank assembly.
Tip:After installing the fuel tank main tube sub-assembly and No. 1 fuel evaporation tube sub-assembly, check that the fuel tank main tube sub-assembly is positioned above the No. 1 fuel evaporation tube sub-assembly.
INSTALL NO. 4 FUEL TANK CUSHION
Install a new No. 4 fuel tank cushion to the fuel tank assembly.
INSTALL NO. 2 FUEL TANK CUSHION
Install 3 new No. 2 fuel tank cushions to the fuel tank assembly.
INSTALL NO. 1 FUEL TANK CUSHION
Install a new No. 1 fuel tank cushion to the fuel tank assembly.
INSTALL FUEL TANK ASSEMBLY
Set the fuel tank assembly on an engine lifter.
Note:Using height adjustment attachments and plate lift attachments, keep the fuel tank assembly horizontal.
Using the engine lifter, slowly raise the fuel tank assembly, and then install the fuel tank assembly with the 2 fuel tank bands with the 4 bolts.
Note:Be careful not to drop the fuel tank assembly.
When installing the fuel tank assembly, tilt it slightly to prevent it from interfering with the surrounding parts.
39.2 N*m
400 kgf*cm
29 ft.*lbf
Connect the parking brake cable assembly with the 2 bolts.
6.0 N*m
61 kgf*cm
53 in.*lbf
CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY
Note:Check that there is no damage or foreign matter on the connecting parts of the fuel lines.
-
*a
Retainer
*b
Fuel Tube Connector
*c
Fuel Pipe
*d
O-ring
*e
Claw

Push

Push in
Connect the fuel tank main tube sub-assembly to the fuel pipe.
Align the fuel tube connector with the fuel pipe, and push them together until the fuel tube connector makes a "click" sound. If it is difficult to push the fuel pipe into the fuel tube connector, apply a small amount of clean gasoline to the tip of the fuel pipe and reinsert it.
Connect the fuel lines and push in the retainer to engage the 2 claws. Check that the fuel pipe and fuel tube connector are securely connected by pulling on them.
-
CONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY
Note:Check that there is no damage or foreign matter on the connecting parts of the fuel lines.
-
*a
Fuel Tube Connector
*b
Fuel Pipe
*c
Retainer
*d
O-ring

Push
Connect the No. 1 fuel evaporation tube sub-assembly to the fuel pipe.
Align the fuel tube connector with the fuel pipe, and push them together until the fuel tube connector makes a "click" sound. If it is difficult to push the fuel pipe into the fuel tube connector, apply a small amount of clean gasoline to the tip of the fuel pipe and reinsert it.
After connecting the fuel lines, check that the fuel pipe and fuel tube connector are securely connected by pulling on them.
-
CONNECT FUEL TANK TO FILLER PIPE HOSE
-
*a
Up
*b
180° (Clamp Bolt Area)
Connect the fuel tank to filler pipe hose to the fuel tank assembly and tighten the clamp to secure it.
Tip:Make sure the bolt of the clamp is positioned within the area shown in the illustration.
-
CONNECT FUEL TANK BREATHER TUBE
-
*1
No. 1 Charcoal Canister Outlet Hose
*2
Fuel Tank Breather Tube
*3
Evaporation Vent Tube Clamp
*a
Up
*b
20°
*c
180° (Clamp Bolt Area)
Connect the fuel tank breather tube to the fuel tank filler pipe sub-assembly as shown in the illustration and tighten the clamp to secure it.
Tip:Make sure the bolt of the clamp is positioned within the area shown in the illustration.
-
CONNECT NO. 1 CHARCOAL CANISTER OUTLET HOSE
Connect the No. 1 charcoal canister outlet hose to the fuel tank filler pipe sub-assembly.
Note:After connecting the fuel tank breather tube and No. 1 charcoal canister outlet hose, check that the evaporation vent tube clamp is securely connected to the fuel tank assembly.
INSTALL NO. 1 FUEL TANK PROTECTOR
Install the No. 1 fuel tank protector to the fuel tank assembly with the 4 bolts.
5.5 N*m
56 kgf*cm
49 in.*lbf
INSTALL TAIL EXHAUST PIPE ASSEMBLY
INSTALL REAR FLOOR SIDE MEMBER COVER LH
INSTALL REAR FLOOR SIDE MEMBER COVER RH
INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
ADD FUEL