ECD SYSTEM(w/ Glow Plug Controller), Diagnostic DTC:P20E2

DTC Code DTC Name
P20E2 Exhaust Gas Temperature Sensor 1/2 Correlation Bank 1

DESCRIPTION

The exhaust gas temperature sensor B1S1 and exhaust gas temperature sensor B1S2 are used to monitor the difference in the temperature of the exhaust gas before and after the DPF catalytic converter. This DTC is stored when a deviation in the characteristics of either sensor is detected.

After a long soak the output of the exhaust gas temperature sensor B1S1 and exhaust gas temperature sensor B1S2 should be approximately the same. When the engine is started after a long soak (engine has been stopped for 6 hours or more), if the difference between output of the exhaust gas temperature sensor B1S1 and exhaust gas temperature sensor B1S2 exceeds the threshold, the ECM will illuminate the MIL and store this DTC.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Memory

P20E2

Exhaust Gas Temperature Sensor 1/2 Correlation Bank 1

The difference between the exhaust gas temperature sensor B1S1 and exhaust gas temperature sensor B1S2 is higher than calibrated threshold when ignition switch to ON after engine stopping longer than 6 houres (2 trip detection logic).

  • Exhaust gas temperature sensor B1S1

  • Exhaust gas temperature sensor B1S2

  • ECM

Comes on

DTC stored

Table 1. DTC Detection Drive Pattern

DTC No.

DTC Detection Drive Pattern

P20E2

Ignition switch ON in cold engine (At least 6 hours ignition switch off).

Table 2. Related Data List

DTC No.

Data List

P20E2

  • Exhaust Temperature B1S1

  • Exhaust Temperature B1S2

CAUTION / NOTICE / HINT

Note:

When replacing the ECM, perform ECM Initialization and Registration.

Click here

Tip:
  • When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing a new ECM, perform all of the initialization and registration procedures for the "Learning Values Write" function by following the instructions shown on the GTS display.

  • Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE

  1. CHECK ANY OTHER DTCS OUTPUT (DTC P20E2)

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    5. Read the DTCs.

      Powertrain > Engine and ECT > Trouble Codes

      Result

      Result

      Proceed to

      DTC P20E2 is output

      A

      DTC P20E2 and other DTCs are output

      B

      Tip:

      If any DTCs other than P20E2 are output, troubleshoot those DTCs first.

    B

    GO TO DTC CHART

    A
  2. READ VALUE USING GTS (EXHAUST TEMPERATURE B1S1 AND EXHAUST TEMPERATURE B1S2)

    1. Leave the vehicle for 6 hours or more.

      Tip:

      It is necessary to leave the vehicle for 6 hours or more to create conditions similar to the DTC detection conditions.

    2. Connect the GTS to the DLC3.

    3. Turn the ignition switch to ON and turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Exhaust Temperature B1S1 and Exhaust Temperature B1S2.

      Powertrain > Engine and ECT > Data List

      Tester Display

      Exhaust Temperature B1S1

      Exhaust Temperature B1S2

    5. Read the Exhaust Temperature B1S1 value on the GTS.

      Standard

      Approximately 50 °C (122 °F)

    6. Read the Exhaust Temperature B1S2 value on the GTS.

      Standard

      Approximately 50 °C (122 °F)

      Tip:

      The value of Exhaust Temperature B1S1 and Exhaust Temperature B1S2 are usually approximately 50°C (122°F) at cold start. If the value of either is extremely high, replace the corresponding exhaust gas temperature sensor with a new one.

      Result

      Result

      Proceed to

      OK

      A

      NG

      (Exhaust Temperature B1S1 value deviated)

      B

      NG

      (Exhaust Temperature B1S2 value deviated)

      C

    A

    REPLACE ECM

    C

    REPLACE EXHAUST GAS TEMPERATURE SENSOR B1S2Click here

    B
  3. REPLACE EXHAUST GAS TEMPERATURE SENSOR B1S1

    1. Replace the exhaust gas temperature sensor B1S1.

      Click here

    Result

    Proceed to

    NEXT

    NEXT

    CHECK WHETHER DTC OUTPUT RECURS (DTC P20E2)Click here

  4. REPLACE EXHAUST GAS TEMPERATURE SENSOR B1S2

    1. Replace the exhaust gas temperature sensor B1S2.

      Click here

    Result

    Proceed to

    NEXT

    NEXT
  5. CHECK WHETHER DTC OUTPUT RECURS (DTC P20E2)

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs.

      Powertrain > Engine and ECT > Clear DTCs

    4. Turn the ignition switch off.

    5. Turn the ignition switch off and leave the vehicle for 6 hours or more.

    6. Start the engine and turn the GTS on.

    7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.

    8. Confirm that the pending DTC is not output again.

      Powertrain > Engine and ECT > Trouble Codes

      Result

      Result

      Proceed to

      DTC P20E2 is output

      A

      DTC is not output

      B

    B

    END

    A
  6. REPLACE ECM

    1. Replace the ECM.

      Click here

    Result

    Proceed to

    NEXT

    NEXT
  7. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs.

      Powertrain > Engine and ECT > Clear DTCs

    4. Turn the ignition switch off.

    5. Turn the ignition switch off and leave the vehicle for 6 hours or more.

    6. Start the engine and turn the GTS on.

    7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.

    8. Confirm that the pending DTC is not output again.

      Powertrain > Engine and ECT > Trouble Codes

    Result

    Proceed to

    NEXT

    NEXT

    END