FRONT DOOR(for Hatchback, Wagon) ADJUSTMENT

CAUTION / NOTICE / HINT

B332382C01

*a

Centering Bolt

*b

Standard Bolt

Tip:
  • Use the same procedure for the RH side and LH side.

  • The procedure listed below is for the LH side.

  • Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts when making adjustments.

  • Specified torque for standard bolts is shown in the standard bolt chart.

    Click here

PROCEDURE

  1. INSPECT FRONT DOOR

    1. Check that the clearance measurements of areas "a" through "o" are within each standard range.

      B332379N01
      Table 1. Standard Clearance

      Area

      Measurement

      Area

      Measurement

      a

      3.9 to 6.9 mm (0.154 to 0.272 in.)

      b

      9.7 to 12.7 mm (0.382 to 0.500 in.)

      c

      3.9 to 6.9 mm (0.154 to 0.272 in.)

      d

      8.9 to 11.9 mm (0.350 to 0.469 in.)

      e

      3.0 to 7.0 mm (0.118 to 0.276 in.)

      f

      3.2 to 5.6 mm (0.126 to 0.220 in.)

      g

      -1.2 to 1.2 mm (-0.0472 to 0.0472 in.)

      h

      3.2 to 5.6 mm (0.126 to 0.220 in.)

      i

      -1.2 to 1.2 mm (-0.0472 to 0.0472 in.)

      j

      4.2 to 7.2 mm (0.165 to 0.283 in.)

      k

      4.2 to 7.2 mm (0.165 to 0.283 in.)

      l

      2.7 to 5.7 mm (0.106 to 0.224 in.)

      m

      -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)

      n

      2.7 to 5.7 mm (0.106 to 0.224 in.)

      o

      -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)

      -

      -

  2. REMOVE FRONT WHEEL

  3. REMOVE FRONT FENDER MUDGUARD (w/ Mudguard)

  4. REMOVE FRONT WHEEL OPENING EXTENSION PAD

    Tip:

    Use the same procedure for the RH side and LH side.

    Click here

  5. REMOVE FRONT FENDER LINER

    Tip:

    Use the same procedure for the RH side and LH side.

    Click here

  6. REMOVE FRONT FENDER SIDE PANEL PROTECTOR (w/ Front Fender Side Panel Protector)

    1. B327701

      Disengage the 2 clips.

    2. Disengage the claw and remove the front fender side panel protector.

  7. ADJUST FRONT DOOR

    Note:

    Make sure to turn the ignition switch off when adjusting door lock strikers.

    1. B332380

      Using SST, loosen the hinge bolts on the vehicle body and adjust the door position.

      09812-00010

    2. Tighten the hinge bolts on the vehicle body after adjustment.

      26 N*m

      265 kgf*cm

      19 ft.*lbf

    3. Loosen the hinge bolts on the door and adjust the door position.

    4. Tighten the hinge bolts on the door after adjustment.

      26 N*m

      265 kgf*cm

      19 ft.*lbf

    5. B327703

      Using a T40 "TORX" socket wrench, slightly loosen the striker mounting screws.

    6. Using a brass bar and a hammer, hit the striker to adjust its position.

    7. Using a T40 "TORX" socket wrench, tighten the striker mounting screws after adjustment.

      23 N*m

      235 kgf*cm

      17 ft.*lbf

  8. INSTALL FRONT FENDER SIDE PANEL PROTECTOR (w/ Front Fender Side Panel Protector)

    1. Engage the claw.

    2. Engage the 2 new clips and install the front fender side panel protector.

  9. INSTALL FRONT FENDER LINER

    Tip:

    Use the same procedure for the RH side and LH side.

    Click here

  10. INSTALL FRONT WHEEL OPENING EXTENSION PAD

    Tip:

    Use the same procedure for the RH side and LH side.

    Click here

  11. INSTALL FRONT FENDER MUDGUARD (w/ Mudguard)

  12. INSTALL FRONT WHEEL