CONTINUOUSLY VARIABLE VALVE LIFT CONTROLLER REMOVAL

PROCEDURE

  1. REMOVE NO. 2 CYLINDER HEAD COVER

  2. REMOVE AIR CLEANER CAP SUB-ASSEMBLY

  3. REMOVE BATTERY

  4. DISCONNECT ENGINE WIRE

    1. Disengage the 9 clamps, and then disconnect the connectors.

    2. Remove the 3 bolts and 2 nuts, and then disconnect the engine wire.

      A294062C02

      *a

      Bolt

      *b

      Nut

  5. REMOVE IGNITION COIL ASSEMBLY

    1. A170843

      Remove the 4 bolts and 4 ignition coil assemblies.

  6. REMOVE AIR TUBE

    1. A282710

      Disconnect the union to connector tube hose.

    2. Disconnect the No. 2 air hose and No. 1 fuel vapor feed hose.

    3. Remove the 2 bolts and air tube from the cylinder head cover sub-assembly.

  7. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

  8. REMOVE CYLINDER HEAD COVER GASKET

  9. REMOVE CONTINUOUSLY VARIABLE VALVE LIFT CONTROLLER ASSEMBLY

    1. A173623

      Using a screwdriver, slide the valve lift control actuator connector clip from the valve lift control actuator connector.

      Note:

      Slide only the upper part of the valve lift control actuator connector clip, as the straight pin will fall out from the bottom if the valve lift control actuator connector clip is completely removed.

    2. A319440C01

      *a

      No. 1 Cylinder

      *b

      No. 3 Cylinder

      Rotate the crankshaft clockwise until the intake camshaft position at the No. 1 cylinder and No. 3 cylinder is as shown in the illustration.

      Tip:

      If the intake camshaft position is not as shown in the illustration, rotate the crankshaft clockwise again so that the intake camshaft is aligned as shown in the illustration.

    3. Turn the crankshaft counterclockwise approximately 10 to 15°.

    4. A319442

      Using 2 screwdrivers, lightly pry the valve lift control actuator connector to make a space between the continuously variable valve lift controller assembly and camshaft housing sub-assembly.

      Note:
      • Do not forcibly pry the valve lift control actuator connector.

      • Do not damage the camshaft housing sub-assembly and camshaft bearing cap.

    5. A174395

      Using a magnet hand, remove the straight pin from the valve lift control actuator connector.

      Note:

      Do not drop the straight pin into the engine.

      Tip:
      • The straight pin can be removed by utilizing the space between the continuously variable valve lift controller assembly and camshaft housing sub-assembly to move the continuously variable valve lift controller assembly so that there is no load on the straight pin.

      • If the straight pin cannot removed easily, slightly turn the crankshaft clockwise and then counterclockwise.

      • If the straight pin could not be removed using a magnet hand, proceed to *1. If the straight pin could be removed, proceed to *2.

    6. A175190

      *1 (If straight pin could not be removed)

      1. Using a screwdriver, remove the valve lift control actuator connector clip from the valve lift control actuator connector.

        Note:

        Do not drop the valve lift control actuator connector clip into the engine.

      2. Align the end of SST with the straight pin hole of the valve lift control actuator connector and push up the straight pin approximately 5 mm (0.197 in.) as shown in the illustration.

        A418956C02

        *1

        Valve Lift Control Actuator Connector

        *2

        Straight Pin

        *a

        Straight Pin Hole

        *b

        Tilt

        *c

        Push up

        -

        -

        09249-37020

      3. A418957C02

        *a

        Protective Tape

        Using pliers, remove the straight pin from the valve lift control actuator connector.

        Note:
        • Make sure to wrap the tips of the pliers with protective tape.

        • Do not drop the straight pin into the engine.

    7. A175190

      *2 (If straight pin could be removed)

      1. Using a screwdriver, remove the valve lift control actuator connector clip from the valve lift control actuator connector.

        Note:

        Do not drop the valve lift control actuator connector clip into the engine.

    8. A173624

      Remove the 2 nuts and wire harness clamp bracket from the camshaft housing sub-assembly.

    9. Remove the bolt from the continuously variable valve lift controller assembly.

    10. A207931

      Remove the continuously variable valve lift controller assembly from the camshaft housing sub-assembly.

      Note:

      If the continuously variable valve lift controller assembly has been struck or dropped, replace it.

    11. A229341C01

      *1

      O-ring

      Remove the O-ring from the continuously variable valve lift controller assembly.

    12. A299868

      Remove the valve lift control actuator connector from the valve rocker shaft assembly.