ECD SYSTEM, Diagnostic DTC:P1229
| DTC Code | DTC Name |
|---|---|
| P1229 | Fuel Pump System |
DESCRIPTION
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
MIL |
Memory |
|---|---|---|---|---|---|
P1229 |
Fuel Pump System |
The actual fuel pressure exceeds the target fuel pressure by 5000 kPa or higher for 30 seconds (1 trip detection logic). |
|
Comes on |
DTC stored |
DTC No. |
Data List |
|---|---|
P1229 |
|
For more information on the supply pump assembly (suction control valve) and common rail system, refer to System Description.
When DTC P1229 is stored, check the internal fuel pressure of the common rail by entering the following menus: Powertrain / Engine and ECT / Data List / All Data / Fuel Press and Target Common Rail Pressure.
Under a stable condition such as idling after warm up the engine, Fuel Press is within +/- 5000 kPa of Target Common Rail Pressure when normal.
When there is a problem with the movement of the supply pump assembly (when Fuel Press is higher than Target Common Rail Pressure due to a problem in which the suction valve has difficulty closing), the values of Injection Pressure Correction and Target Pump SCV Current decrease.
MONITOR DESCRIPTION
P1229 (Fuel overfeed):
The ECM stores this DTC if the actual fuel pressure inside the common rail assembly remains higher than the target fuel pressure, despite the ECM closing the suction control valve. This DTC indicates that the suction control valve may be stuck open, or there may be a short in its circuit.
If this DTC is stored, the ECM enters fail-safe mode and limits the engine power. The ECM continues operating in fail-safe mode until the ignition switch is turned off.
CONFIRMATION DRIVING PATTERN
DTC No. |
DTC Detection Drive Pattern |
|---|---|
P1229 |
Idling for 60 seconds |
WIRING DIAGRAM
Refer to DTC P0088.
CAUTION / NOTICE / HINT
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
After replacing the suction control valve, the ECM needs initialization.
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
When this DTC is stored, be sure to carefully examine "Fuel Press", "Target Common Rail Pressure", "Target Pump SCV Current", and "Pump SCV Learning Value" in the freeze frame data.
PROCEDURE
CHECK OTHER DTC OUTPUT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
Powertrain > Engine and ECT > Trouble Codes
Result
Result
Proceed to
Except below
A
DTC P1229 and "P0190, P0192 and/or P0193" are output
B
READ VALUE USING GTS (FUEL PRESS AND TARGET COMMON RAIL PRESSURE)
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Start the engine and warm it up.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Fuel Press and Target Common Rail Pressure.
Powertrain > Engine and ECT > Data List
Tester Display
Target Common Rail Pressure
Fuel Press
Check that the internal fuel pressure of the common rail assembly is within the specification below.
OK
Fuel Press is within 5000 kPa of Target Common Rail Pressure when engine is idling after warm up the engine.
Result
Proceed to
OK
NG
CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)
Result
Proceed to
OK
NG
OK REPLACE FUEL FILTER ELEMENT SUB-ASSEMBLYClick here
REPAIR OR REPLACE HARNESS OR CONNECTOR
Repair or replace the harness or connector.
Result
Proceed to
NEXT
PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak / All Data / Fuel Press and Target Common Rail Pressure.
Powertrain > Engine and ECT > Active Test
Active Test Display
Test the Fuel Leak
Data List Display
Target Common Rail Pressure
Fuel Press
Take a snapshot with the GTS during the Active Test.
Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Fuel Press) when the "Test the Fuel Leak" Active Test is performed.
Tip:In order to obtain an exact measurement, perform the Active Test 5 times and measure the difference once each time the Active Test is performed.
OK
The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa (102.0 kgf/cm2, 1451 psi).
Tip:"Target Common Rail Pressure" is the target fuel pressure controlled by the ECM.
"Fuel Press" is the actual fuel pressure in common rail assembly.
Result
Result
Proceed to
Except below
A
The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa (102.0 kgf/cm2, 1451 psi).
B
B CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIREDClick here
REPLACE FUEL FILTER ELEMENT SUB-ASSEMBLY
Replace the fuel filter element sub-assembly.
Result
Proceed to
NEXT
REPLACE SUCTION CONTROL VALVE
Replace the suction control valve.
Result
Proceed to
NEXT
BLEED AIR FROM FUEL SYSTEM
Bleed the air from the fuel system.
Result
Proceed to
NEXT
PERFORM SUPPLY PUMP INITIALIZATION
Perform the supply pump initialization.
Result
Proceed to
NEXT
CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Powertrain > Engine and ECT > Clear DTCs
Turn the ignition switch off for 30 seconds or more.
Start the engine and turn the GTS on.
Idle the engine for 60 seconds, and then run it at 2500 rpm without load for 60 seconds.
Confirm that the DTC is not output.
Tip:Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
Input DTC P1229.
Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, increase the idling time.
Result
Proceed to
NEXT
NEXT END