ENGINE UNIT DISASSEMBLY

CAUTION / NOTICE / HINT

Note:
  • When replacing the injector assemblies (including exchanging the injector assemblies between the cylinders), common rail assembly, intake manifold or cylinder head sub-assembly, it is necessary to replace the injection pipe sub-assemblies with new ones.

  • When replacing the fuel tube sub-assembly, supply pump assembly, common rail assembly, intake manifold or cylinder head sub-assembly, it is necessary to replace the fuel inlet pipe sub-assembly with a new one.

PROCEDURE

  1. REMOVE NO. 2 NOZZLE LEAKAGE PIPE

    1. A291637C04

      *1

      No. 2 Nozzle Leakage Pipe

      *a

      Check Valve

      Remove the check valve and gasket.

    2. Remove the bolt and No. 2 nozzle leakage pipe.

  2. REMOVE NO. 1 NOZZLE LEAKAGE PIPE

    1. A291638

      Remove the 4 union bolts and 4 gaskets.

    2. Remove the bolt and No. 1 nozzle leakage pipe.

  3. REMOVE NO. 1 NOZZLE HOLDER CLAMP

    1. A263727

      Remove the 4 bolts, 4 washers and 4 No. 1 nozzle holder clamps.

  4. REMOVE INJECTOR ASSEMBLY

  5. REMOVE CAMSHAFT POSITION SENSOR

    1. A291639

      Remove the bolt and camshaft position sensor.

  6. REMOVE CRANKSHAFT POSITION SENSOR

    1. A291640

      Remove the clip and disconnect the crankshaft position sensor harness.

    2. Remove the 2 bolts and crankshaft position sensor.

  7. REMOVE ENGINE COOLANT TEMPERATURE SENSOR

    1. A203791N01

      Using SST, remove the engine coolant temperature sensor and gasket.

      09817-33190

  8. REMOVE ENGINE WATER PUMP ASSEMBLY

  9. REMOVE OIL PRESSURE SENDER GAUGE ASSEMBLY

  10. REMOVE OIL COOLER ASSEMBLY

  11. REMOVE NO. 1 OIL COOLER BRACKET

  12. REMOVE ENGINE OIL LEVEL SENSOR

    1. A263730

      Remove the 4 bolts and engine oil level sensor.

  13. REMOVE WATER INLET HOUSING

  14. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

  15. REMOVE OIL PAN SUB-ASSEMBLY

  16. REMOVE OIL FILTER ELEMENT

  17. REMOVE OIL PRESSURE SWITCHING VALVE ASSEMBLY

  18. REMOVE OIL FILTER BRACKET

  19. REMOVE OIL STRAINER SUB-ASSEMBLY

  20. REMOVE CRANKSHAFT PULLEY

    1. Set the No. 1 cylinder to TDC/compression.

      1. A202382C04

        *a

        Timing Pointer

        *b

        Timing Mark

        Turn the crankshaft pulley clockwise to align the timing mark on the crankshaft pulley with the timing pointer on of the timing chain cover sub-assembly.

    2. A294405C02

      *a

      Matchmark

      *b

      Timing Mark

      Make sure that the timing mark of the camshaft timing sprocket is at the top.

      Tip:

      If the timing mark is not at the top, turn the crankshaft pulley 1 revolution so that the timing mark is at the top (set the No. 1 cylinder to TDC/compression).

    3. Put a matchmark on the timing chain plate that is aligned with the timing mark of the camshaft timing sprocket.

      Tip:

      The timing chain has 2 pink-colored mark plates. If either of them is aligned with the timing mark of the camshaft timing sprocket, this step can be omitted.

    4. A202384N01

      Turn the crankshaft pulley approximately 90° clockwise from the timing pointer on the timing chain cover sub-assembly so that a lifted valve and piston will not contact each other when removing the camshafts.

    5. A201753N01

      Using SST, hold the crankshaft pulley and loosen the crankshaft pulley bolt.

      09213-58014

      91551-80840

      09330-00021

    6. A201752N01

      Using SST, remove the crankshaft pulley.

      09950-50013

      09951-05010

      09952-05010

      09953-05020

      09954-05021

  21. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

  22. REMOVE FRONT CRANKSHAFT OIL SEAL

  23. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

    1. A202386C04

      *a

      Plunger

      *b

      Stopper Plate

      Move the stopper plate upward to release the lock, and push the plunger deep into the No. 1 chain tensioner assembly.

    2. Move the stopper plate downward to set the lock, and insert SST into the stopper plate hole.

      09240-00020

      09242-00200

    3. A202387

      Remove the 2 bolts and No. 1 chain tensioner assembly from the cylinder block sub-assembly.

  24. REMOVE CHAIN TENSIONER SLIPPER

    A202388
    1. Remove the chain tensioner slipper from the cylinder block sub-assembly.

  25. REMOVE NO. 1 CHAIN VIBRATION DAMPER

    1. A202389

      Remove the 2 bolts and No. 1 chain vibration damper.

  26. REMOVE CAMSHAFT TIMING SPROCKET

    1. A294406

      Remove the 4 bolts from the camshaft timing sprocket while holding the hexagonal portion of the No. 2 camshaft with a wrench.

    2. Remove the camshaft timing sprocket and chain sub-assembly.

  27. REMOVE OIL PUMP DRIVE GEAR

    1. A202391

      Remove the oil pump drive gear from the crankshaft.

  28. REMOVE CRANKSHAFT TIMING SPROCKET

    1. A202392

      Remove the crankshaft timing sprocket from the crankshaft.

  29. REMOVE CRANKSHAFT PULLEY SET CRANKSHAFT KEY

    1. A202393

      Remove the 2 crankshaft pulley set crankshaft keys from the crankshaft.

  30. REMOVE CAMSHAFT

  31. REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

  32. REMOVE VALVE LASH ADJUSTER ASSEMBLY

  33. REMOVE CYLINDER HEAD SUB-ASSEMBLY

  34. REMOVE CYLINDER HEAD GASKET

  35. REMOVE REAR CRANKSHAFT OIL SEAL

  36. REMOVE NO. 1 OIL PAN BAFFLE PLATE

    1. A129588

      Remove the 4 bolts and No. 1 oil pan baffle plate.

  37. REMOVE CYLINDER BLOCK DRAIN COCK PLUG

    1. A291641

      Remove the cylinder block drain cock plug from the cylinder block sub-assembly.