SFI SYSTEM Lack of Power or Hesitation
| DTC Code | DTC Name |
|---|---|
| Lack of Power or Hesitation |
DESCRIPTION
The VALVEMATIC system is able to continuously change the valve lift amount and valve timing. For engines equipped with a VALVEMATIC system, when a part such as a rocker arm in the camshaft housing has mechanical problems, the valve lift amount does not change and problems occur, such as a lack of engine power or rough idling.
CAUTION / NOTICE / HINT
A lack of engine power occurs when the throttle valve is malfunctioning or when there is a clog in the intake or exhaust system. Therefore, during the inspection, confirm that there are no clogs in any parts.
When the throttle valve is malfunctioning, even if the accelerator pedal is fully depressed when the engine is running, the throttle does not fully open.
When there is a clog in the intake system, even if the accelerator pedal is fully depressed, the MAP is not the same as the atmospheric pressure.
When performing this inspection on a vehicle equipped with the VALVEMATIC, perform the following procedures first in order to confirm that there are no VVT system malfunctions.
Perform the VVT system Active Test and confirm that the VVT follows the VVT target.
If the VVT system Active Test results are normal, perform the VALVEMATIC system Active Test.
When the vehicle is not equipped with the VALVEMATIC, even if the VVT system inspection (the inspection that checks if idling becomes unstable when changing the VVT to the most advanced and retarded positions through the Active Test) is performed, it cannot be determined that the malfunction is in the VVT system.
PROCEDURE
CHECK WHETHER DTC OUTPUT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
Powertrain > Engine and ECT > Trouble Codes
Result
Result
Proceed to
DTC is not output
A
DTC is output
B
PERFORM BASIC FUNCTION
Check the air cleaner filter element sub-assembly.
Tip:If the air cleaner filter element sub-assembly is dirty, clean or replace it.
Check if there are any clogs in the intake or exhaust system.
Check the ignition timing.
Check the fuel pressure.
Check the spark.
Measure the cylinder compression pressure.
Result
Result
Proceed to
Everything normal
A
Repaired problem area but malfunction reoccurs
Repaired problem area and malfunction does not reoccur
B
Tip:Perform "Inspection After Repair" after repairing or replacing the intake system, exhaust system, ignition system or engine assembly.
B END
READ VALUE USING GTS
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Short FT #1, Long FT #1, AFS Voltage B1S1 and O2S B1S2.
Powertrain > Engine and ECT > Data List
Tester Display
AFS Voltage B1S1
O2S B1S2
Short FT #1
Long FT #1
Read the value while driving the vehicle.
Result
Result
Proceed to
No abnormal values in Data List
A
Abnormal values in Data List
B
B CHECK FUEL SYSTEM
PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT SYSTEM (BANK 1))
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT System (Bank1) / All Data / VVT Change Angle #1.
Powertrain > Engine and ECT > Active Test
Active Test Display
Control the VVT System (Bank1)
Data List Display
VVT Change Angle #1
Read the value.
Result
Result
Proceed to
The "VVT Change Angle #1" value changes
A
The "VVT Change Angle #1" value does not change
B
PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VALVEMATIC(ENG ON))
Connect the GTS to the DLC3.
Start the engine and warm it up until the engine coolant temperature stabilizes. (Engine coolant temperature 40°C or higher)
Turn the ignition switch off.
Restart the engine.
Tip:Do not operate the accelerator pedal.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VALVEMATIC(ENG ON) / Data List / MAP, VALVEMATIC Target Angle, VALVEMATIC Current Angle, VALVEMATIC bef Warm Up.
Powertrain > Engine and ECT > Active Test
Active Test Display
Activate the VALVEMATIC(ENG ON)
Data List Display
MAF
VALVEMATIC Target Angle
VALVEMATIC Current Angle
VALVEMATIC bef Warm Up
Check the Data List "VALVEMATIC bef Warm Up" display is "ON".
Tip:If "VALVEMATIC bef Warm Up" is not "ON".
Restart the engine. (Do not operate the accelerator pedal.)
Perform the Active Test "Activate the VALVEMATIC before Warm Up" to set "VALVEMATIC bef Warm Up" to "ON". (Do not operate the accelerator pedal.)
Set the Active Test "Activate the VALVEMATIC(ENG ON)" to "High" and check that "VALVEMATIC Current Angle" follows "VALVEMATIC Target Angle" and the "MAP" value changes.
Standard
GTS Operation
Result
High
VALVEMATIC Current Angle: 260 deg(CA)
MAP: 25 to 40 kPa (188 to 300 mmHg)
Set the Active Test "Activate the VALVEMATIC(ENG ON)" to "OFF", and check that "VALVEMATIC bef Warm Up" returns to "ON".
Set the Active Test "Activate the VALVEMATIC(ENG ON)" to "Low" and check that "VALVEMATIC Current Angle" follows "VALVEMATIC Target Angle" and the "MAP" value changes.
Standard
GTS Operation
Result
Low
VALVEMATIC Current Angle: 106 deg(CA)
MAP: 35 to 65 kPa (263 to 488 mmHg)
OK
When performing the Active Test, "VALVEMATIC Current Angle" follows "VALVEMATIC Target Angle" and the "MAP" value changes.
Tip:After the accelerator pedal is depressed and the Active Test operates once to "Low", "VALVEMATIC bef Warm Up" does not return to "ON". Therefore, in order to repeat the inspection, it is necessary to either perform the Active Test "Activate the VALVEMATIC before Warm Up" to set the VALVEMATIC system to the operating position that occurs before the engine is warmed up, or restart the engine.
When the vehicle is driven while there is a malfunction in the VALVEMATIC system and the valve lift amount is fixed at the minimum, the vehicle speed cannot exceed 30 to 60 km/h (19 to 37 mph).
If the intake valve advance angle is within the VALVEMATIC operation prohibition range depending on the operating state of the VVT system, the Active Test "Activate the VALVEMATIC(ENG ON)" is prohibited. If the advance angle cannot be detected due to a malfunction in the VVT system, the Active Test "Activate the VALVEMATIC(ENG ON)" is prohibited.
Result
Proceed to
OK
NG
OK PERFORM SIMULATION TEST