ROOF DRIP SIDE FINISH MOULDING INSTALLATION

CAUTION / NOTICE / HINT

Tip:
  • Use the same procedure for the RH and LH sides.

  • The procedure described below is for the LH side.

PROCEDURE

  1. INSTALL NO. 1 ROOF DRIP SIDE FINISH MOULDING CLIP (for Standard Roof)

    Note:

    When installing new No. 1 roof drip side finish moulding clips, remove the double-sided tape remaining where the No. 1 roof drip side finish moulding clips will be installed on the body and clean the body with non-residue solvent.

    1. B329294C05

      *a

      Adhesive

      *b

      2 to 3 mm bead of adhesive

      Apply a 2 to 3 mm (0.0787 to 0.118 in.) bead of adhesive (3M DP-105 or equivalent) to 2 new No. 1 roof drip side finish moulding clips.

      Tip:

      Adhesive strength (tensile strength): 13.7 MPa (140.0 kgf/cm2, 1987 psi) or more (when the temperature is 23°C (73°F).)

    2. B329296C02

      *a

      Protruding part

      Install the No. 1 roof drip side finish moulding clips to the positions on the roof panel shown in the illustration. Determine the locations and firmly press and install the 2 No. 1 roof drip side finish moulding clips after lightly applying adhesive (3M DP-105 or equivalent).

      Table 1. Standard Dimension

      Dimension

      Measurement

      A

      3.9 mm (0.154 in.)

      B

      4.0 mm (0.157 in.)

      C

      2.4 mm (0.0945 in.)

      D

      1.5 mm (0.0591 in.)

      E

      3.4 mm (0.134 in.)

      F

      3.6 mm (0.142 in.)

      G

      2.6 mm (0.102 in.)

      H

      1.2 mm (0.0472 in.)

    3. Install the center roof drip side finish moulding when 20 minutes or more have elapsed after pressing and installing the 2 No. 1 roof drip side finish moulding clips.

      Tip:
      • Initial hardening time: 20 minutes

      • Complete hardening time: 48 hours

  2. INSTALL NO. 1 ROOF DRIP SIDE FINISH MOULDING CLIP (for Glass Roof)

    Note:

    When installing new No. 1 roof drip side finish moulding clips, remove the double-sided tape remaining where the No. 1 roof drip side finish moulding clips will be installed on the body and clean the body with non-residue solvent.

    1. B329294C03

      *1

      Adhesive

      *a

      2 to 3 mm bead of adhesive

      Apply a 2 to 3 mm (0.0787 to 0.118 in.) bead of adhesive (3M DP-105 or equivalent) to 2 new No. 1 roof drip side finish moulding clips.

      Tip:

      Adhesive strength (tensile strength): 13.7 MPa (140.0 kgf/cm2, 1987 psi) or more (when the temperature is 23°C (73°F).)

    2. B329295C02

      *a

      Protruding part

      Install the No. 1 roof drip side finish moulding clips to the positions on the roof panel shown in the illustration. Determine the locations and firmly press and install the 2 No. 1 roof drip side finish moulding clips after lightly applying adhesive (3M DP-105 or equivalent).

      Table 2. Standard Dimension

      Dimension

      Measurement

      A

      4.0 mm (0.157 in.)

      B

      4.0 mm (0.157 in.)

      C

      2.4 mm (0.0945 in.)

      D

      1.5 mm (0.0591 in.)

      E

      3.4 mm (0.134 in.)

      F

      3.6 mm (0.142 in.)

      G

      2.6 mm (0.102 in.)

      H

      1.2 mm (0.0472 in.)

    3. Install the center roof drip side finish moulding when 20 minutes or more have elapsed after pressing and installing the 2 No. 1 roof drip side finish moulding clips.

      Tip:
      • Initial hardening time: 20 minutes

      • Complete hardening time: 48 hours

  3. INSTALL CENTER ROOF DRIP SIDE FINISH MOULDING (for Standard Roof)

    1. B330336

      Engage the 2 No. 1 roof drip side finish moulding clips and install the center roof drip side finish moulding.

  4. INSTALL CENTER ROOF DRIP SIDE FINISH MOULDING (for Glass Roof)

    1. B330337

      Engage the 2 No. 1 roof drip side finish moulding clips and install the center roof drip side finish moulding.