CLUTCH UNIT(for EC65A) INSTALLATION

CAUTION / NOTICE / HINT

Note:

When the multi-mode manual transaxle assembly is removed, be sure to use a new clutch release with bearing cylinder assembly and new installation bolts. Removal of the multi-mode manual transaxle assembly allows the compressed clutch release with bearing cylinder assembly to return to its original position. Dust from the moving section may damage the seal of the clutch release with bearing cylinder assembly, possibly causing clutch fluid leaks.

PROCEDURE

  1. INSTALL CLUTCH DISC ASSEMBLY

    C274622C01

    *1

    Clutch Disc Assembly

    *a

    Flywheel Sub-assembly Side

    1. Insert SST into the clutch disc assembly, then insert them both into the flywheel sub-assembly.

      09301-00210

      Note:

      Insert the clutch disc assembly in the correct direction.

  2. INSTALL CLUTCH COVER ASSEMBLY

    C274623C01

    *a

    Temporarily

    *b

    Matchmark

    1. Align the matchmark on the clutch cover assembly with the one on the flywheel sub-assembly.

    2. Following the procedure shown in the illustration, tighten the 6 bolts in order, starting with the bolt located near the knock pin at the top.

      09301-00210

      19.1 N*m

      195 kgf*cm

      14 ft.*lbf

      Tip:
      • Following the order in the illustration, tighten the bolts evenly one at a time.

      • Move SST up and down, right and left lightly after checking that the disc is in the center, and tighten the bolts.

  3. INSPECT AND ADJUST CLUTCH COVER ASSEMBLY

    1. C274888

      Using a dial indicator with a roller instrument, check the diaphragm spring tip alignment.

      Maximum Non-alignment

      0.5 mm (0.0197 in.)

    2. C208436N02

      If the alignment is not as specified, using SST, adjust the diaphragm spring tip alignment.

      09333-00013

  4. INSTALL CLUTCH RELEASE WITH BEARING CYLINDER ASSEMBLY

    1. C197022

      Temporarily tighten the clutch release cylinder to bleeder tube to a new clutch release with bearing cylinder assembly.

    2. Clean and degrease all installation surfaces for the clutch release with bearing cylinder assembly.

    3. Install the clutch release with bearing cylinder assembly with 3 new bolts.

      22.5 N*m

      229 kgf*cm

      17 ft.*lbf

      Note:
      • The clutch release with bearing cylinder assembly and installation bolts cannot be reused and must be replaced with new ones.

      • Clean and degrease all installation surfaces and make sure that the clutch release with bearing cylinder assembly fits securely with the multi-mode manual transaxle assembly during installation. The first bolt should be tightened by hand holding the clutch release with bearing cylinder assembly.

      • Ensure that none of the clutch disc spline grease adheres to the clutch release with bearing cylinder assembly.

      • The clutch release with bearing cylinder assembly cannot be disassembled.

    4. Install the clutch tube boot to the multi-mode manual transaxle assembly.

    5. C274624

      Temporarily tighten the clutch release cylinder to bleeder tube to the clutch release bleeder sub-assembly.

    6. Temporarily tighten the 2 bolts and install the clutch release bleeder sub-assembly.

    7. C197021

      Using a 10 mm union nut wrench, install the clutch release cylinder to bleeder tube to the clutch release with bearing cylinder assembly.

      15.2 N*m

      155 kgf*cm

      11 ft.*lbf

      Note:
      • Use a torque wrench with a fulcrum length of 250 mm (9.84 in.).

      • Use the torque value compensation formula to calculate the torque value for use when a torque wrench is combined with a tool such as a union nut wrench.

        Click hereClick hereClick hereClick here

    8. C196061C02
      V100135

      Clutch spline grease

      Apply clutch spline grease to the input shaft spline.

      Sealant

      Toyota Genuine Clutch Spline Grease or equivalent

  5. REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

    1. C274624

      Separate the clutch release cylinder to bleeder tube from the clutch release bleeder sub-assembly.

    2. Remove the 2 bolts and clutch release bleeder sub-assembly from the multi-mode manual transaxle assembly.

  6. INSPECT CLUTCH PIPE LINE

    C207357E01
    1. Using SST, apply pressure of 100 kPa (1.0 kgf/cm2, 15 psi) to the clutch pipe location shown in the illustration and confirm that pressure is maintained for 15 seconds or more.

      09992-00242

      If the pressure drops, replace the clutch release cylinder to bleeder tube.

  7. INSTALL CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

    1. C274624

      Temporarily tighten the clutch release cylinder to bleeder tube to the clutch release bleeder sub-assembly.

    2. Install the 2 bolts and clutch release bleeder sub-assembly to the multi-mode manual transaxle assembly.

      16.7 N*m

      170 kgf*cm

      12 ft.*lbf

    3. Using a 10 mm union nut wrench, install the clutch release cylinder to bleeder tube to the clutch release bleeder sub-assembly.

      15.2 N*m

      155 kgf*cm

      11 ft.*lbf

      Note:
      • Use a torque wrench with a fulcrum length of 250 mm (9.84 in.).

      • Use the torque value compensation formula to calculate the torque value for use when a torque wrench is combined with a tool such as a union nut wrench.

        Click hereClick hereClick hereClick here

  8. INSTALL BLEEDER CLUTCH RELEASE TUBE

    C202593
    1. Using a 10 mm union nut wrench, install the bleeder clutch release tube to the clutch release bleeder sub-assembly and clutch actuator assembly.

      15.2 N*m

      155 kgf*cm

      11 ft.*lbf

      Note:
      • Use a torque wrench with a fulcrum length of 250 mm (9.84 in.).

      • Use the torque value compensation formula to calculate the torque value for use when a torque wrench is combined with a tool such as a union nut wrench.

        Click hereClick hereClick hereClick here

  9. INSTALL MULTI-MODE MANUAL TRANSAXLE ASSEMBLY