LIN COMMUNICATION SYSTEM, Diagnostic DTC:B2321

DTC Code DTC Name
B2321 Driver Side Door ECU Communication Stop

DESCRIPTION

This DTC is stored when LIN communication between the front door window regulator assembly (for driver door) and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

B2321

Driver Side Door ECU Communication Stop

No communication between front door window regulator assembly (for driver door) and main body ECU (multiplex network body ECU) for 10 seconds or more.

  • Front door window regulator assembly (for driver door)

  • Main body ECU (multiplex network body ECU)

  • Power window regulator master switch assembly*1

  • Wire harness or connector

  • DOOR NO. 1*1

  • DOOR NO. 2*2

  • *1: for Models with Jam Protection Function on 4 Windows

  • *2: for Models with Jam Protection Function on Driver Door Window Only

WIRING DIAGRAM

  1. for Models with Jam Protection Function on 4 Windows

    1. for LHD

      B228561E33
    2. for RHD

      B228561E34
  2. for Models with Jam Protection Function on Driver Door Window Only

    1. for LHD

      B274860E34
    2. for RHD

      B274860E35

CAUTION / NOTICE / HINT

Note:
  • Inspect the fuses for circuits related to this system before performing the following procedure.

  • When a front door window regulator assembly is replaced or removed and reinstalled, it requires initialization.

    for Models with Jam Protection Function on 4 Windows:Click here

    for Models with Jam Protection Function on Driver Door Window Only:Click here

PROCEDURE

  1. SYSTEM CHECK

    1. Check the vehicle specifications.

    Result

    Result

    Proceed to

    for Models with Jam Protection Function on 4 Windows

    A

    for Models with Jam Protection Function on Driver Door Window Only

    B

    B

    CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - FRONT DOOR WINDOW REGULATOR ASSEMBLY (for Driver Door))Click here

    A
  2. CHECK DTC OUTPUT

    1. Clear the DTCs.

      Click here

      Body Electrical > Main Body > Clear DTCs

    2. Recheck for DTCs.

      Body Electrical > Main Body > Trouble Codes

    Result

    Result

    Proceed to

    Only DTC B2321 is output.

    A

    DTC B1206 and B2321 are output simultaneously.

    B

    Tip:

    When DTC B1206 and B2321 are output simultaneously, perform troubleshooting for DTC B1206 first.

    B

    GO TO DTC B1206

    A
  3. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT DOOR WINDOW REGULATOR ASSEMBLY (for Driver Door))

    1. for LHD

      1. Disconnect the H12 power window regulator master switch assembly connector.

      2. Disconnect the H14 front door window regulator assembly (for driver door) connector.

      3. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection

        Condition

        Specified Condition

        H12-16 (LIN2) - H14-9 (LIN)

        Always

        Below 1 Ω

        H12-16 (LIN2) - Body ground

        Always

        10 kΩ or higher

        H14-9 (LIN) - Body ground

        Always

        10 kΩ or higher

    2. for RHD

      1. Disconnect the G3 power window regulator master switch assembly connector.

      2. Disconnect the G5 front door window regulator assembly (for driver door) connector.

      3. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection

        Condition

        Specified Condition

        G3-16 (LIN2) - G5-9 (LIN)

        Always

        Below 1 Ω

        G3-16 (LIN2) - Body ground

        Always

        10 kΩ or higher

        G5-9 (LIN) - Body ground

        Always

        10 kΩ or higher

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK
  4. INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

    1. B234549C05

      *a

      Component without harness connected

      (Power Window Regulator Master Switch Assembly)

      Remove the power window regulator master switch assembly.

      Click hereClick here

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      16 (LIN2) - 17 (LIN1)

      Always

      Below 1 Ω

    Result

    Proceed to

    OK

    NG

    NG

    REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

    OK
  5. CHECK HARNESS AND CONNECTOR (FRONT DOOR WINDOW REGULATOR ASSEMBLY (for Driver Door) - BATTERY, BODY GROUND)

    1. for LHD

      1. Measure the voltage according to the value(s) in the table below.

        Standard Voltage

        Tester Connection

        Condition

        Specified Condition

        H14-2 (B) - H14-1 (GND)

        Always

        11 to 14 V

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection

        Condition

        Specified Condition

        H14-1 (GND) - Body ground

        Always

        Below 1 Ω

    2. for RHD

      1. Measure the voltage according to the value(s) in the table below.

        Standard Voltage

        Tester Connection

        Condition

        Specified Condition

        G5-2 (B) - G5-1 (GND)

        Always

        11 to 14 V

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection

        Condition

        Specified Condition

        G5-1 (GND) - Body ground

        Always

        Below 1 Ω

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK
  6. REPLACE FRONT DOOR WINDOW REGULATOR ASSEMBLY (for Driver Door)

    1. Replace the front door window regulator assembly (for driver door).

      Click here

    Result

    Proceed to

    NEXT

    NEXT
  7. CHECK DTC OUTPUT

    1. Clear the DTCs.

      Click here

      Body Electrical > Main Body > Clear DTCs

    2. Recheck for DTCs.

      Body Electrical > Main Body > Trouble Codes

      OK

      DTC B2321 is not output.

    Result

    Proceed to

    OK

    NG

    OK

    END (FRONT DOOR WINDOW REGULATOR ASSEMBLY (for Driver Door) WAS DEFECTIVE)

    NG

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

    for LHD:Click here

    for RHD:Click here

  8. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - FRONT DOOR WINDOW REGULATOR ASSEMBLY (for Driver Door))

    1. for LHD

      1. Disconnect the 3C instrument panel junction block assembly connector.

      2. Disconnect the H14 front door window regulator assembly (for driver door) connector.

      3. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection

        Condition

        Specified Condition

        3C-23 - H14-9 (LIN)

        Always

        Below 1 Ω

        H14-9 (LIN) - Body ground

        Always

        10 kΩ or higher

        3C-23 - Body ground

        Always

        10 kΩ or higher

    2. for RHD

      1. Disconnect the 3C instrument panel junction block assembly connector.

      2. Disconnect the G5 front door window regulator assembly (for driver door) connector.

      3. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection

        Condition

        Specified Condition

        3C-23 - G5-9 (LIN)

        Always

        Below 1 Ω

        G5-9 (LIN) - Body ground

        Always

        10 kΩ or higher

        3C-23 - Body ground

        Always

        10 kΩ or higher

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK
  9. INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

    1. Remove the instrument panel junction block assembly.

      for LHD:Click here

      for RHD:Click here

      B330524C03

      *a

      Component without harness connected

      (Instrument Panel Junction Block Assembly)

      -

      -

    2. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

    3. Measure the resistance according to the value(s) in the table below.

      Tip:

      This inspection is to check the LIN communication line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      3C-23 - MB-16 (LIN2)

      Always

      Below 1 Ω

    Result

    Proceed to

    OK

    NG

    NG

    REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

    for LHD:Click here

    for RHD:Click here

    OK
  10. CHECK HARNESS AND CONNECTOR (FRONT DOOR WINDOW REGULATOR ASSEMBLY (for Driver Door) - BATTERY, BODY GROUND)

    1. for LHD

      1. Measure the voltage according to the value(s) in the table below.

        Standard Voltage

        Tester Connection

        Condition

        Specified Condition

        H14-2 (B) - H14-1 (GND)

        Always

        11 to 14 V

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection

        Condition

        Specified Condition

        H14-1 (GND) - Body ground

        Always

        Below 1 Ω

    2. for RHD

      1. Measure the voltage according to the value(s) in the table below.

        Standard Voltage

        Tester Connection

        Condition

        Specified Condition

        G5-2 (B) - G5-1 (GND)

        Always

        11 to 14 V

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection

        Condition

        Specified Condition

        G5-1 (GND) - Body ground

        Always

        Below 1 Ω

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK
  11. REPLACE FRONT DOOR WINDOW REGULATOR ASSEMBLY (for Driver Door)

    1. Replace the front door window regulator assembly (for driver door).

      for Sedan:Click here

      except Sedan:Click here

    Result

    Proceed to

    NEXT

    NEXT
  12. CHECK DTC OUTPUT

    1. Clear the DTCs.

      Click here

      Body Electrical > Main Body > Clear DTCs

    2. Recheck for DTCs.

      Body Electrical > Main Body > Trouble Codes

      OK

      DTC B2321 is not output.

    Result

    Proceed to

    OK

    NG

    OK

    END (FRONT DOOR WINDOW REGULATOR ASSEMBLY (for DRIVER DOOR) WAS DEFECTIVE)

    NG

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

    for LHD:Click here

    for RHD:Click here