LIN COMMUNICATION SYSTEM, Diagnostic DTC:B1273

DTC Code DTC Name
B1273 Sliding Roof ECU Communication Stop

DESCRIPTION

This DTC is stored when LIN communication between the roof sunshade ECU (sliding roof drive gear assembly) and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

B1273

Sliding Roof ECU Communication Stop

No communication between roof sunshade ECU (sliding roof drive gear assembly) and main body ECU (multiplex network body ECU) for 10 seconds or more.

  • Roof sunshade ECU (sliding roof drive gear assembly)

  • Main body ECU (multiplex network body ECU)

  • Instrument panel junction block assembly

  • Wire harness or connector

  • S-ROOF fuse

WIRING DIAGRAM

B315277E22

CAUTION / NOTICE / HINT

Note:
  • Inspect the fuses for circuits related to this system before performing the following procedure.

  • When the roof sunshade ECU (sliding roof drive gear assembly) is replaced or removed and reinstalled, it requires initialization.

    Click here

PROCEDURE

  1. INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

    1. Remove the instrument panel junction block assembly.

      for LHD:Click hereClick here

      for RHD:Click hereClick here

      B330524C03

      *a

      Component without harness connected

      (Instrument Panel Junction Block Assembly)

      -

      -

    2. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

    3. Measure the resistance according to the value(s) in the table below.

      Tip:

      This inspection is to check the LIN communication line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      3C-22 - MB-16 (LIN2)

      Always

      Below 1 Ω

    Result

    Proceed to

    OK

    NG

    NG

    REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

    OK
  2. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY))

    1. Disconnect the a1 roof sunshade ECU (sliding roof drive gear assembly) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      3C-22 -a1-11 (LIN)

      Always

      Below 1 Ω

      a1-11 (LIN) - Body ground

      Always

      10 kΩ or higher

      3C-22 - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK
  3. CHECK HARNESS AND CONNECTOR (ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) - BATTERY, BODY GROUND)

    1. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Condition

      Specified Condition

      a1-8 (B) - a1-12 (E)

      Always

      11 to 14 V

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      a1-12 (E) - Body ground

      Always

      Below 1 Ω

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK
  4. REPLACE ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)

    1. Replace the roof sunshade ECU (sliding roof drive gear assembly).

      Click here

    Result

    Proceed to

    NEXT

    NEXT
  5. CHECK DTC OUTPUT

    1. Clear the DTCs.

      Click here

      Body Electrical > Main Body > Clear DTCs

    2. Recheck for DTCs.

      Body Electrical > Main Body > Trouble Codes

      OK

      DTC B1273 is not output.

    Result

    Proceed to

    OK

    NG

    OK

    END (ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) WAS DEFECTIVE)

    NG

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)