AUDIO AND VISUAL SYSTEM(except Sedan Radio and Display Type) DTC CHECK / CLEAR

  1. CHECK DTC (CHECK USING GTS)

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Navigation System / Trouble Codes.

    5. Check for DTCs, and then write them down.

      Body Electrical > Navigation System > Trouble Codes

    6. Check the details of the DTC(s).

      Click here

      Note:

      The audio and visual system outputs DTCs for the following system. When DTCs other than those in Diagnostic Trouble Code Chart for the audio and visual system are output, refer to Diagnostic Trouble Code Chart for the relevant system.

      System

      Proceed to

      Rear View Monitor System

      Click here

  2. CLEAR DTC (CLEAR USING GTS)

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Navigation System / Trouble Codes.

    5. Clear the DTCs.

      Body Electrical > Navigation System > Clear DTCs

  3. START DIAGNOSTIC MODE

    Tip:
    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

    • Start diagnostic mode at least 15 seconds after turning the ignition switch to ON. Otherwise, some items cannot be checked.

    1. There are 2 methods to start diagnostic mode. Start diagnostic mode by using either of them.

    2. Method 1

      1. Turn the ignition switch to ON.

      2. While pressing and holding the "CAR" switch, operate the light control switch: Off → Tail → Off → Tail → Off → Tail → Off.

    3. Method 2

      1. Turn the ignition switch to ON.

      2. Press the seek/track up panel switch 5 times and then press the seek/track down panel switch 5 times with the screen and audio turned off.

        Tip:
        • Diagnostic mode can only be started if the above operation is completed within 15 seconds of the first press of the seek/track up panel switch.

        • If the operation is not completed within 15 seconds of the first press of the seek/track panel switch or fails, turn the screen and audio on and then off again before attempting to start diagnostic mode.

    4. Diagnostic mode starts and the "Service Menu" screen will be displayed. Service inspection starts automatically and the result will be displayed.

  4. FAILURE DIAGNOSIS

    1. E226135

      The "Failure Diagnosis" screen will be displayed by pressing the "Failure Diagnosis" switch on the "Service Menu" screen.

  5. SYSTEM CHECK

    1. E268518

      The "System Check Mode" screen will be displayed by pressing the "System Check" switch on the "Failure Diagnosis" screen.

  6. CHECK DTC (CHECK USING SYSTEM CHECK MODE SCREEN)

    1. E277791N02

      System check mode screen description

      Table 1. Screen Description

      Display

      Content

      *a: Device name list No. 1

      • Device Name List No. 1 displays some of the devices that make up the audio and visual system.

      • The names of the components from Device Name List No. 1 are shown in the following table.

      *b: Check result

      Result codes for all devices are displayed.

      *c: Memory clear

      • Present and history DTCs and registered connected device names are cleared.

      • Press the "Memory CLR" switch for 3 seconds.

      *d: Recheck

      • A system check will be performed again after the memory is cleared.

      • The "Recheck" switch will dim during a system check.

      *e: Device name list No. 2

      • Device Name List No. 2 displays some of the devices that make up the audio and visual system.

      • The names of the components from Device Name List No. 2 are shown in the following table.

      Table 2. *a: Device Name List No. 1 Description

      Name

      Component

      Connection Method

      DA

      Radio and display receiver assembly

      -

      Table 3. *b: Check Result Description

      Result

      Meaning

      Action

      OK

      The device does not respond with a DTC.

      -

      DETAIL

      The device responds with a DTC.

      Look up the DTC in "Unit Check Mode".

      Table 4. *e: Device Name List No. 2 Description

      Name

      Component

      Connection Method

      AUX/VTR

      No. 1 stereo jack adapter assembly

      Vehicle wire harness

    2. E226127N04

      Unit check mode screen description

      Table 5. Screen Description

      Display

      Content

      *a: Device name

      Target device

      *b: History DTC

      Diagnostic memory results and stored DTCs are displayed.

      *c: Current DTC

      DTCs output in the service check are displayed.

      *d: DTC

      DTC (Diagnostic Trouble Code)

      *e: Diagnosis clear switch

      Pushing this switch for 3 seconds clears the diagnostic memory data of the target device (both diagnostic system check result and the displayed data are cleared).

      Tip:
      • This screen is updated once per second.

      • A maximum of 6 DTCs can be displayed for history and present DTCs.

    3. E277793
      E277792

      Read the system check result.

      1. If the check result is "DETAIL", touch the displayed check result to view the results on the "Unit Check Mode" screen and record them.

        Note:

        A maximum of 6 DTCs can be displayed for history and present DTCs on the "Unit Check Mode" screen. Therefore, when 6 DTCs are displayed, troubleshoot those DTCs first and then check the "Unit Check Mode" screen again to see if any other DTCs are displayed.

        Tip:
        • When all results are "OK", this means that no DTCs are present.

        • When proceeding to view the results of another device, press the "Back" switch to return to the "System Check Mode" screen. Repeat the step above to view the results of other devices.

      2. Check the details of the DTC(s).

        Click here

        Note:

        The audio and visual system outputs DTCs for the following system. When DTCs other than those in Diagnostic Trouble Code Chart for the audio and visual system are output, refer to Diagnostic Trouble Code Chart for the relevant system.

        Rear View Monitor System

        System

        Proceed to

        Rear View Monitor System

        Click here

  7. DTC CLEAR/RECHECK (CLEAR USING SYSTEM CHECK MODE SCREEN)

    1. E277794

      Clear DTCs

      1. Press the "Memory CLR" switch for 3 seconds.

      2. Confirm that the check results are cleared.

        Tip:
        • To clear the DTCs for a specific device, clear the DTCs using the "Unit Check Mode" screen.

        • When clearing the DTCs using the "Unit Check Mode" screen, press the "Code CLR" switch for 3 seconds.

    2. E277795

      Recheck

      1. Press the "Recheck" switch.

      2. E277796

        Confirm that all diagnostic codes are "OK" when the check results are displayed. If a code other than "OK" is displayed, troubleshoot again.

        Tip:

        When DTCs are cleared using the "Unit Check Mode" screen, press the "Back" switch to return to the "System Check Mode" screen and perform this operation.

  8. FINISH DIAGNOSTIC MODE

    1. Turn the ignition switch off.