LIN COMMUNICATION SYSTEM, Diagnostic DTC:B2789

DTC Code DTC Name
B2789 No Response from ID BOX

DESCRIPTION

This DTC is stored when LIN communication between the certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) stops for 10 seconds or more.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

B2789

No Response from ID BOX

No communication between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) for 10 seconds or more.

  • ID code box (immobiliser code ECU)

  • Certification ECU (smart key ECU assembly)

  • Wire harness or connector

  • ECU-B NO. 2 fuse

WIRING DIAGRAM

B273275E34

CAUTION / NOTICE / HINT

Note:
  • Inspect the fuses for circuits related to this system before performing the following procedure.

  • If the certification ECU (smart key ECU assembly) is replaced, register the keys (refer to Service Bulletin)

  • If the ID code box (immobiliser code ECU) is replaced, register the ECU code and ECU communication ID (refer to Service Bulletin)

PROCEDURE

  1. CHECK DTC OUTPUT

    1. Clear the DTCs.

      Click here

      Body Electrical > Entry&Start > Clear DTCs

    2. Recheck for DTCs.

      Body Electrical > Entry&Start > Trouble Codes

    Tip:

    When DTC B2789 and B2785 are output simultaneously, perform troubleshooting for DTC B2785 first.

    Result

    Result

    Proceed to

    Only B2789 is output

    A

    DTC B2789 and B2785 are output simultaneously

    B

    B

    GO TO DTC B2785

    A
  2. CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - BATTERY, BODY GROUND)

    1. Disconnect the E87 ID code box (immobiliser code ECU) connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Condition

      Specified Condition

      E87-1 (+B) - E87-5 (GND)

      Always

      11 to 14 V

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      E87-5 (GND) - Body ground

      Always

      Below 1 Ω

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK
  3. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ID CODE BOX (IMMOBILISER CODE ECU))

    1. Disconnect the E35 certification ECU (smart key ECU assembly) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      E35-17 (LIN) - E87-2 (LIN)

      Always

      Below 1 Ω

      E35-17 (LIN) - Body ground

      Always

      10 kΩ or higher

      E87-2 (LIN) - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK
  4. REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

    1. Replace the ID code box (immobiliser code ECU).

      Tip:

      Refer to Service Bulletin.

    Result

    Proceed to

    NEXT

    NEXT
  5. CHECK DTC OUTPUT

    1. Clear the DTCs.

      Click here

      Body Electrical > Entry&Start > Clear DTCs

    2. Recheck for DTCs.

      Body Electrical > Entry&Start > Trouble Codes

      OK

      DTC B2789 is not output.

    Result

    Proceed to

    OK

    NG

    OK

    END (ID CODE BOX (IMMOBILISER CODE ECU) WAS DEFECTIVE)

    NG

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)