THEFT DETERRENT SYSTEM Security Horn Circuit

DTC Code DTC Name
Security Horn Circuit

DESCRIPTION

When the theft deterrent system is switched from the armed state to the alarm sounding state, the main body ECU (multiplex network body ECU) transmits a signal to cause the security horn to sound at intervals of 0.4 seconds.

WIRING DIAGRAM

B332812E01

CAUTION / NOTICE / HINT

Note:

Inspect the fuses for circuits related to this system before performing the following procedure.

PROCEDURE

  1. PERFORM ACTIVE TEST USING GTS (SECURITY HORN)

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body / Active Test.

    5. Perform the Active Test according to the display on the GTS.

      Body Electrical > Main Body > Active Test

      Tester Display

      Measurement Item

      Control Range

      Diagnostic Note

      Security Horn

      Security horn

      OFF/ON

      -

      Body Electrical > Main Body > Active Test

      Tester Display

      Security Horn

      OK

      The security horn assembly sounds and stops correctly when operated through the GTS.

    Result

    Proceed to

    OK

    NG

    OK

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

    NG
  2. INSPECT SECURITY HORN ASSEMBLY

    B330450
    1. Remove the security horn.

      Click here

    2. Check the operation of the security horn assembly.

      OK

      Battery Connection

      Specified Condition

      Battery positive (+) → Terminal 1

      Battery negative (-) → Security horn body

      Horn sounds

    Result

    Proceed to

    OK

    NG

    NG

    REPLACE SECURITY HORN ASSEMBLY

    OK
  3. INSPECT S-HORN RELAY

    1. B256934C02

      *1

      S-HORN Relay

      Remove the S-HORN relay from the No. 4 relay block.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      3 - 5

      When battery voltage is not applied between terminals 1 and 2

      10 kΩ or higher

      3 - 5

      When battery voltage is applied between terminals 1 and 2

      Below 1 Ω

    Result

    Proceed to

    OK

    NG

    NG

    REPLACE S-HORN RELAY

    OK
  4. INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

    1. Remove the main body ECU (multiplex network body ECU).

      Click hereClick here

      B332811C01

      *a

      Component without harness connected

      (Instrument Panel Junction Block Assembly)

      -

      -

    2. Disconnect the 3C instrument panel junction block assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      3C-40 - MB-17 (SH)

      Always

      Below 1 Ω

    Result

    Proceed to

    OK

    NG

    NG

    REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

    OK
  5. CHECK HARNESS AND CONNECTOR (BATTERY - S-HORN RELAY)

    1. B332813C01

      *1

      No. 4 Relay Block

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Condition

      Specified Condition

      No. 4 relay block S-HORN relay terminal 1 - Body ground

      Always

      11 to 14 V

      No. 4 relay block S-HORN relay terminal 5 - Body ground

      Always

      11 to 14 V

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK
  6. CHECK HARNESS AND CONNECTOR (S-HORN RELAY - SECURITY HORN ASSEMBLY)

    1. B332813C01

      *1

      No. 4 Relay Block

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      No. 4 relay block S-HORN relay terminal 3 - A122-1

      Always

      Below 1 Ω

      No. 4 relay block S-HORN relay terminal 3 - Body ground

      Always

      10 kΩ or higher

      A122-1 - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK
  7. CHECK HARNESS AND CONNECTOR (S-HORN RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

    1. B332813C02

      *1

      No. 4 Relay Block

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      No. 4 relay block S-HORN relay terminal 2 - 3C-40

      Always

      Below 1 Ω

      No. 4 relay block S-HORN relay terminal 2 - Body ground

      Always

      10 kΩ or higher

      3C-40 - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG

    OK

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR