AUDIO AND VISUAL SYSTEM(except Sedan Radio and Display Type) OPERATION CHECK

  1. CHECK PANEL & STEERING SWITCH

    Tip:
    • The radio and display receiver assembly panel switches and steering switches are checked in the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

    1. Enter diagnostic mode.

      Click here

    2. E225777

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. E265426

      Select "Panel & Steering Switch" from the "Function Check/Setting I" screen.

    4. E225786N01

      Panel & Steering Switch Check Mode

      Table 1. Screen Description

      Display

      Content

      *a: Switch condition

      "Pushed" is displayed when any switch is pushed

      *b: Number of switches pushed

      • Number of switches pushed at once is displayed

      • If more than 3 switches are pushed at once, "More than 3" is displayed

      *c: Rotary switch direction

      Direction of rotary switch is displayed

      1. Operate each switch and check that the switch conditions are correctly displayed.

        Note:

        When the "SETUP" switch is pressed and held for 3 seconds or more, diagnostic mode will be canceled.

  2. CHECK TOUCH SWITCH

    Tip:
    • The touch switches on the screen are checked in the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

    1. Enter diagnostic mode.

      Click here

    2. E225777

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. E265427

      Select "Touch Switch" from the "Function Check/Setting I" screen.

    4. E176521

      Touch Switch Check

      1. Touch the display anywhere in the open area to perform the check when the "Touch Switch Check" screen is displayed.

        Tip:
        • A "+" mark is displayed where the display is touched.

        • The "+" mark remains on the display even after your finger is removed.

  3. CHECK MICROPHONE & VOICE RECOGNITION

    Tip:
    • The microphone and microphone input level are checked in the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

    1. Enter diagnostic mode.

      Click here

    2. E225777

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. E265428

      Select "Mic & Voice Recognition" from the "Function Check/Setting I" screen.

    4. E225853E02

      Microphone & Voice Recognition Check

      Table 2. Screen Description

      Display

      Content

      *a: Microphone input level meter

      Monitors the microphone input level every 0.1 seconds and displays the results in 8 different levels.

      1. When speaking into the microphone, check that the microphone input level meter changes according to the input level.

        Tip:

        The microphone is active at all times when this screen is displayed.

  4. CHECK COLOR BAR

    Tip:
    • The display color on the screen is checked in the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

    1. Enter diagnostic mode.

      Click here

    2. E225777

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. E265429

      Select "Color Bar" from the "Function Check/Setting I" screen.

    4. E226305

      Color Bar Check Mode

      1. Select a color bar from the "Color Bar Check Mode" screen.

      2. Check the display color.

        Tip:
        • The entire screen turns to the color or stripe selected.

        • Touching the display will return to the "Color Bar Check Mode" screen.

  5. CHECK VEHICLE SIGNAL

    Tip:
    • Vehicle signals received by the radio and display receiver assembly are checked in the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

    1. Enter diagnostic mode.

      Click here

    2. E225777

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. E265430

      Select "Vehicle Signal" from the "Function Check/Setting I" screen.

    4. E225776

      Vehicle Signal Check Mode

      Table 3. Screen Description

      Display

      Content

      Battery

      Battery voltage is displayed.

      IG

      Ignition switch ON/OFF state is displayed.

      PKB

      Parking brake ON/OFF state is displayed.

      REV

      Reverse signal ON/OFF state is displayed.

      SPEED

      Vehicle speed is displayed in km/h.

      TAIL

      Tail signal (light control switch) ON/OFF state is displayed.

      ADIM/TCAN

      Brightness state DIM (with)/BRIGHT (without) is displayed.

      Tip:
      • Only items sending vehicle signals will be displayed.

      • This screen displays vehicle signals input to the radio and display receiver assembly.

      • This screen is updated once per second when vehicle input signals change.

      1. When the "Vehicle Signal Check Mode" screen is displayed, check all the vehicle signal conditions.

  6. CHECK HANDS-FREE VOICE QUALITY AND VOLUME SETTING

    Tip:
    • The hands-free volume of a "Bluetooth" compatible phone can be adjusted using the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

    1. Enter diagnostic mode.

      Click here

    2. E225777

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. E265431

      Select "HF Voice Quality Setting" from the "Function Check/Setting I" screen.

    4. E225788E01

      Hands-Free Voice Quality Setting (Receive/Send Voice Level adjustment)

      Table 4. Screen Description

      Display

      Content

      *a: Receive voice level adjustment

      Setting for the voice level received from "Bluetooth" compatible phones.

      *b: Send voice level adjustment

      Setting for the voice level sent from "Bluetooth" compatible phones.

      Note:

      Sound quality may deteriorate when the receive voice or send voice level is changed more than necessary. For this reason, check that the received voice or sent voice quality is still acceptable after changing this setting.

      1. If the voice level is low, press the up button, and if the voice level is loud, press the down button.

        Tip:
        • Each voice level setting is reflected when going back to the normal mode.

        • The voice level adjustment ranges from -5 to +5.

        • The initial level is "0".

    5. E228924C01

      *a

      Numeric keypad

      *b

      Setting button

      *c

      Reset button

      Hands-Free Voice Quality Setting (Voice Quality Type adjustment)

      1. If necessary, refer to the table below to adjust the voice quality type with the numeric keypad.

      2. When adjusting the settings, use the number pad on the screen to input the voice quality type according to the table.

        Table 5. Setting

        Parameter

        Target Phenomenon

        Voice Quality Type (FUJITSU TEN)

        Voice Quality Type (Panasonic)

        Voice Quality Type (Pioneer)

        Positive Effects of Changing Voice Quality

        Negative Effects of Changing Voice Quality

        Echo

        The other party hears a lot of echo when speaking to you.

        1000

        2000

        0001

        0001

        0002

        0003

        0004

        0005

        The amount of echo the other party hears of their own voice is reduced.

        When both parties speak at the same time, your voice suddenly drops in volume, cuts out etc.

        Half Duplex

        When both parties speak at the same time, your voice suddenly drops in volume, cuts out etc.

        0100

        0200

        0002

        0010

        0020

        0030

        0040

        0050

        When both parties speak at the same time, the phenomenon by which the other party's voice suddenly drops in volume, cuts out etc. reduces.

        The amount of echo the other party hears of their own voice increases.

        Noise

        The other party hears a lot of vehicle noise etc. when listening to your voice.

        0010

        0020

        -

        0100

        0200

        0300

        0400

        0500

        The amount of vehicle noise etc. the other party hears when listening to your voice reduces.

        The quality of your voice, that the other party hears, reduces.

        Voice Quality

        The quality of your voice, that the other party hears, is low.

        0001

        0002

        0003

        1000

        2000

        3000

        4000

        5000

        The quality of your voice, that the other party hears, increases.

        The amount of noise etc. the other party hears when listening to your voice increases.

        Tip:
        • Refer to the "Unit Version Information" screen to confirm radio and display receiver assembly manufacturer information.

        • The type of adjustments that can be made using voice quality type adjustment only adjusts the sound quality of your voice that the other party hears. It cannot adjust the sound quality of the other party's voice that you hear.

        • The default value is "0000".

        • Settings will be applied when the normal screen is returned to.

        • When multiple setting values are available, the higher the setting value, the bigger the effect. However, as the positive effects increase, so do the negative effects.

        • If voice quality type values that are not in the table are input, the setting will not be applied and a positive effect may not be gained.

        • If the quality of phone calls decreases due to the changed settings, return the settings to "0000" by pressing the "INIT" switch.

  7. CHECK DAB RECEPTION (w/ DAB Function)

    Tip:
    • The reception condition of DAB (Digital Audio Broadcast) can be checked.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

    1. Enter diagnostic mode.

      Click here

    2. E225777

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. E265432

      Select "Next Page" from the "Function Check/Setting I" screen.

    4. E235721

      Select "DAB Reception Check" from the "Function Check/Setting II" screen.

    5. E245217N01

      DAB Reception Check

      Table 6. *a: Channel Change Switch Description

      Display

      Content

      Up or down button

      Enables the channel to be changed to the one to be checked.

      Table 7. *b: Check Switch Description

      Display

      Condition

      Content

      Check

      Before/after check

      Starts checking

      STOP

      During check

      Stops checking

      Table 8. *c: Antenna Connection Check Result Description

      Display

      Content

      OK

      Connected properly

      NG

      Not connected properly

      -

      Not equipped with DAB antenna

      Table 9. *d: DAB Tuner Reception Level Check Result Description

      Display

      Content

      Black

      Good reception

      Red

      Poor reception

      -

      Not equipped with DAB antenna

      1. Select the "Check" button to start the DAB reception check.

      2. Check that the results are displayed when the DAB reception check is performed.

  8. CHECK UNIT VERSION INFORMATION

    Tip:

    Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

    1. Enter diagnostic mode.

      Click here

    2. E229432

      Select "Service Information" from the "Service Menu" screen.

    3. E228230

      Select "Version Information" from the "Service Information" screen.

    4. E228231

      Press the "Push" switch.

    5. E228232N02

      Unit Version Information

      Table 10. Screen Description

      Display

      Content

      *a: Device name

      Target device

      *b: Manufacturer name

      Manufacturer of the ECU (target device)

      *c: Component name

      Component name of the ECU (target device)

      *d: Version

      Version of the ECU (target device)

      Tip:

      Depending on the manufacturer, some component names and versions will be displayed differently.

  9. CHECK SOFTWARE ERROR HISTORY

    Tip:

    This function is used to check the cause when the radio and display receiver assembly screen is blacked out.

    1. Check software error history.

      1. Connect the GTS to the DLC3.

      2. Turn the ignition switch to ON.

      3. Turn the GTS on.

      4. Enter the following menus: Body Electrical / Navigation System / Utility / Software Error History.

        Body Electrical > Navigation System > Utility

        Tester Display

        Software Error History

      5. When an item is stored for Software Error History, record it before repairing the radio and display receiver assembly.

        Table 11. Software Error History Screen Description

        Error Description

        Trigger

        Detail

        Software Reset

        Navi Microcomputer

        Hexadecimal Number

        Audio Microcomputer

        CAN Microcomputer

        No Video Signal

        Front Monitor

        Rear Monitor

        MOST Cold Restart

        Always

        Tip:
        • Software Error History can store up to 5 history data items. If a new software error occurs when 5 data items have already been stored, the oldest data is cleared and the new data is stored.

        • If an error that is unsupported by the GTS occurs, a "-" is displayed for the display items.

    2. Clear software error history.

      1. When DTCs are cleared using any of the following operations, Software Error History will be cleared as well.

        Click here

        • Cleared using the GTS.

        • Cleared using the system check mode screen.

        • Cleared using the unit check mode screen.

  10. CHECK OPTICAL DISC ERROR HISTORY

    Tip:

    This function is used to check the cause of an optical disc error.

    1. Check optical disc error history.

      1. Connect the GTS to the DLC3.

      2. Turn the ignition switch to ON.

      3. Turn the GTS on.

      4. Enter the following menus: Body Electrical / Navigation System / Utility / Optical Disc Error History.

        Body Electrical > Navigation System > Utility

        Tester Display

        Optical Disc Error History

      5. When an item is stored for Optical Disc Error History, record it before proceeding with troubleshooting.

        Table 12. Optical Disc Error History Screen Description

        Display

        Content

        Error Type

        Displays the type of error.

        Device

        Displays the malfunctioning device.

        Date

        Displays the date and time that the malfunction occurred.

        Table 13. "Error Type" Screen Description

        Error Type

        Detection Condition

        Action

        Read Error

        When a disc read error occurs.

        Proceed to next suspected area shown in Problem Symptoms Table.

        Click here

        Disc damaged/upside down/dirty

        When it is determined that any of the following is the cause of the disc read error:

        • The disc cannot be read.

        • The disc cannot be read because of dirt or scratches.

        • The disc cannot be read because it is inserted upside down.

        Cannot determine disc type

        An unsuitable disc is inserted.

        DPS error

        When an error occurs while decoding MP3/WMA files.

        Some files are corrupt

        • When MP3/WMA files cannot be played back because they are unsupported.

        • Even though the file extensions are MP3 or WMA, files cannot be played back because the header information cannot be read.

        Some files cannot be found

        • When a disc without music data is played back.

        • When there are no playable MP3/WMA files.

        Copy protection violation

        When a file with copyright protection that cannot be played back is played back.

        Table 14. "Device" Screen Description

        Device

        Component

        DVD-P

        Not available

        CD-P

        Radio and display receiver assembly

        R-Seat DVD-P

        Not available

        Tip:
        • Optical Disc Error History can store up to 7 history data items. If a new optical disc error occurs when 7 data items have already been stored, the oldest data is cleared and the new data is stored.

        • If an error that is unsupported by the GTS occurs, a "-" or blank is displayed for the display items.

    2. Clear optical disc error history.

      1. When DTCs are cleared using any of the following operations, Optical Disc Error History will be cleared as well.

        Click here

        • Cleared using the GTS.

        • Cleared using the system check mode screen.

        • Cleared using the unit check mode screen.