THEFT DETERRENT SYSTEM TERMINALS OF ECU

  1. CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

    1. Disconnect the main body ECU (multiplex network body ECU) connectors.

      B332798C01

      *A

      Main body ECU (multiplex network body ECU) with 1 connector

      -

      -

      *1

      Main body ECU (multiplex network body ECU)

      -

      -

      *a

      1 connector

      -

      -

      B332794C01

      *A

      Main body ECU (multiplex network body ECU) with 2 connectors

      -

      -

      *1

      Main body ECU (multiplex network body ECU)

      -

      -

      *a

      2 connectors

      -

      -

    2. Measure the resistance and voltage according to the value(s) in the table below.

      Tip:

      Measure the values on the wire harness side with the connector disconnected.

      Tester Connection

      Wiring Color

      Terminal Description

      Condition

      Specified Condition

      MB-30 (BECU) - Body ground

      -

      Battery power supply

      Always

      11 to 14 V

      MB-32 (IG) - Body ground

      -

      Ignition power supply (IG signal)

      Ignition switch ON → OFF

      11 to 14 V → Below 1 V

      MB-29 (ACC) - Body ground

      -

      Ignition power supply (ACC signal)

      Ignition switch ACC → OFF

      11 to 14 V → Below 1 V

      MB-11 (GND1) - Body ground

      -

      Ground

      Always

      Below 1 Ω

      MB-2 (FLCY) - Body ground

      -

      Front door courtesy light switch LH input

      Front door LH closed (OFF) → open (ON)

      10 kΩ or higher → Below 1 Ω

      E22-19 (FRCY) - Body ground

      V - Body ground

      Front door courtesy light switch RH input

      Front door RH closed (OFF) → open (ON)

      10 kΩ or higher → Below 1 Ω

      E22-24 (LCTY) - Body ground

      SB - Body ground

      Rear door courtesy light switch LH input

      Rear door LH closed (OFF) → open (ON)

      10 kΩ or higher → Below 1 Ω

      E22-6 (RCTY) - Body ground

      LG - Body ground

      Rear door courtesy light switch RH input

      Rear door RH closed (OFF) → open (ON)

      10 kΩ or higher → Below 1 Ω

      MB-20 (BCTY) - Body ground

      -

      Back door courtesy light switch input

      Back door closed (OFF) → open (ON)

      10 kΩ or higher → Below 1 Ω

      E108-5 (HCTY) - Body ground

      SB - Body ground

      Engine hood courtesy switch input

      Engine hood open (OFF) → closed (ON)

      10 kΩ or higher → Below 1 Ω

      E22-17 (KSW) - Body ground*

      V - Body ground

      Unlock warning switch input

      Key not in key cylinder (OFF) → Key in key cylinder (ON)

      10 kΩ or higher → Below 1 Ω

      • *: w/o Entry and Start System

      If the result is not as specified, there may be a malfunction in the wire harness.

    3. Reconnect the main body ECU (multiplex network body ECU) connectors.

    4. Measure the voltage and check for pulses according to the value(s) in the table below.

      Tester Connection

      Wiring Color

      Terminal Description

      Condition

      Specified Condition

      E22-7 (LSFL) - Body ground

      Y - Body ground

      Front door LH unlock detection switch input

      Front door LH unlocked

      Below 1 V

      E22-7 (LSFL) - Body ground

      Y - Body ground

      Front door LH unlock detection switch input

      Front door LH locked

      Pulse generation

      E22-18 (LSFR) - Body ground

      LG - Body ground

      Front door RH unlock detection switch input

      Front door RH unlocked

      Below 1 V

      E22-18 (LSFR) - Body ground

      LG - Body ground

      Front door RH unlock detection switch input

      Front door RH locked

      Pulse generation

      3E-37 (LSR) - Body ground

      Y- Body ground

      Rear door LH unlock detection switch input

      Rear door LH or RH unlocked

      Below 1 V

      3E-37 (LSR) - Body ground

      Y - Body ground

      Rear door LH unlock detection switch input

      Rear door LH and RH locked

      Pulse generation

      3E-22 (LSR) - Body ground

      Y - Body ground

      Rear door RH unlock detection switch input

      Rear door RH or LH unlocked

      Below 1 V

      3E-22 (LSR) - Body ground

      Y - Body ground

      Rear door RH unlock detection switch input

      Rear door RH and LH locked

      Pulse generation

      E108-22 (IND) - Body ground*

      Y - Body ground

      Security indicator illumination

      Security indicator light illuminates

      (It illuminates only for 27.5 second in alarm sounding state.)

      3 to 10 V

      3C-40 (SH) - Body ground

      R - Body ground

      Security horn drive

      Security horn sounding

      (Theft deterrent system in alarm sounding state)

      Pulse generation

      (Below 1 V ← → 11 to 14 V)

      3A-24 (HORN) - Body ground

      LG - Body ground

      Vehicle horn drive

      Vehicle horns sounding

      (Theft deterrent system in alarm sounding state)

      Pulse generation

      (Below 1 V ← → 11 to 14 V)

      • *: w/o Entry and Start System

      If the result is not as specified, the main body ECU (multiplex network body ECU) may be malfunctioning.