SFI SYSTEM, Diagnostic DTC:P010012

DTC Code DTC Name
P010012 Mass or Volume Air Flow Sensor "A" Circuit Short to Battery

DESCRIPTION

The mass air flow meter sub-assembly is a sensor that measures the intake air volume. The ECM uses this information to determine the ignition timing and fuel injection duration necessary for an optimal air-fuel ratio. Inside the mass air flow meter sub-assembly are a hot wire element and a cold wire element which are exposed to the flow of intake air. The bridge circuit shown in the illustration outputs voltage to transmit information regarding heat loss of the hot wire element caused by air flow. Depending on the air flow, this voltage will change between approximately 0.2 V and 4.9 V. Based on this voltage, the ECM calculates the air flow to determine the ignition timing and fuel injection duration necessary for an optimal air-fuel ratio.

Tip:

When P010012 is stored, the ECM enters fail-safe mode. During fail-safe mode, boost prohibited and the ignition timing is calculated by the ECM, according to the engine speed and throttle valve position. Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.

A160257E09

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Memory

Note

P010012

Mass or Volume Air Flow Sensor "A" Circuit Short to Battery

The mass air flow meter sub-assembly voltage is higher than 4.9 V for 3 seconds (1 trip detection logic).

  • Open or short in mass air flow meter sub-assembly circuit

  • Mass air flow meter sub-assembly

  • ECM

Comes on

DTC stored

SAE Code: P0103

Tip:

When this DTC is output, check the mass air flow in the Data List. Enter the following menus: Powertrain / Engine / Data List / All Data / Mass Air Flow Sensor.

DTC No.

Mass Air Flow Sensor

Malfunction

P010012

271.0 gm/sec or more

  • Short in VG circuit to power source circuit

  • Open in E2G circuit

If the Data List values is normal it may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.

MONITOR DESCRIPTION

If there is a defect or an open or short circuit in the mass air flow meter sub-assembly, the voltage level deviates from the normal operating range. The ECM interprets this deviation as a malfunction in the mass air flow meter sub-assembly circuit and stores this DTC.

Example:

When the sensor output voltage remains higher than 4.9 V for 3 seconds or more, the ECM stores this DTC.

MONITOR STRATEGY

Frequency of Operation

Continuous

CONFIRMATION DRIVING PATTERN

  1. Connect the GTS to the DLC3.

  2. Turn the ignition switch to ON and turn the GTS on.

  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  4. Turn the ignition switch off and wait for at least 30 seconds.

  5. Turn the ignition switch to ON and turn the GTS on.

  6. Wait 5 seconds or more.

  7. Enter the following menus: Powertrain / Engine / Trouble Codes.

  8. Read the pending DTCs.

    Tip:
    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  9. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  10. Input the DTC: P010012.

  11. Check the DTC judgment result.

    GTS Display

    Description

    NORMAL

    • DTC judgment completed

    • System normal

    ABNORMAL

    • DTC judgment completed

    • System abnormal

    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions

    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    Tip:
    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

    • If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.

WIRING DIAGRAM

A349501E04

CAUTION / NOTICE / HINT

Note:

Inspect the fuses for circuits related to this system before performing the following procedure.

Tip:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE

  1. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)

    1. Disconnect the mass air flow meter sub-assembly connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      B2-2 (E2G) - B208-91 (E2G)

      Always

      Below 1 Ω

      B2-3 (VG) or B208-92 (VG) - Other terminals

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK
  2. CHECK HARNESS AND CONNECTOR (SENSOR GROUND)

    1. Disconnect the mass air flow meter sub-assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      B2-2 (E2G) - Body ground

      Always

      Below 1 Ω

      Tip:

      Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

      Click hereClick here

    Result

    Proceed to

    OK

    NG

    OK

    REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

    NG

    REPLACE ECM