OIL PUMP REMOVAL

CAUTION / NOTICE / HINT

Note:
  • When replacing the injectors (including shuffling the injectors between the cylinders), common rail, intake manifold or cylinder head, it is necessary to replace the injection pipes with new ones.

  • When replacing the fuel supply pump, common rail, intake manifold or cylinder head, it is necessary to replace the fuel inlet pipe with a new one.

PROCEDURE

  1. INSTALL ENGINE TO ENGINE STAND

  2. REMOVE GENERATOR ASSEMBLY

  3. REMOVE VACUUM PUMP ASSEMBLY

    1. A263885

      Disconnect the vacuum hose.

    2. Remove the 3 bolts and vacuum pump assembly.

    3. Remove the 2 O-rings from the vacuum pump assembly.

  4. REMOVE IDLER PULLEY COVER PLATE

    1. A201745C03

      *a

      Tape

      Using a screwdriver, remove the idler pulley cover plate.

      Tip:

      Tape the screwdriver tip before use.

  5. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

    1. A201746

      Remove the bolt and No. 1 idler pulley sub-assembly.

  6. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY

    1. A201747C01

      *1

      No. 2 Idler Pulley Cover Plate

      *2

      No. 2 Idler Pulley Sub-Assembly

      Remove the bolt, No. 2 idler pulley cover plate and No. 2 idler pulley sub-assembly.

  7. REMOVE NO. 4 WATER BY-PASS PIPE

    1. A201735

      Remove the bolt and No. 4 water by-pass pipe from the water inlet housing.

    2. Remove the O-ring from the No. 4 water by-pass pipe.

  8. REMOVE ENGINE MOUNTING BRACKET

    1. A201748

      Remove the 4 bolts, 2 nuts and engine mounting bracket.

  9. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

    1. A201749

      Remove the 3 bolts and V-ribbed belt tensioner assembly.

      Note:

      As the heads of the bolts are not as thick as those of typical bolts, be careful not to damage them during removal.

  10. REMOVE DIESEL THROTTLE BODY ASSEMBLY

  11. REMOVE NO. 7 WATER BY-PASS HOSE

  12. DISCONNECT NO. 8 WATER BY-PASS HOSE

  13. REMOVE EGR VALVE BRACKET

  14. REMOVE NO. 2 EGR PIPE SUB-ASSEMBLY

  15. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY

  16. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

  17. REMOVE FUEL INLET PIPE SUB-ASSEMBLY

  18. REMOVE INJECTION PIPE SUB-ASSEMBLY

  19. REMOVE NO. 4 FUEL HOSE

    A263886
    1. Slide the 2 clips and remove the No. 4 fuel hose.

  20. REMOVE COMMON RAIL ASSEMBLY

  21. REMOVE INTAKE MANIFOLD INSULATOR

  22. REMOVE DIESEL TURBO PRESSURE SENSOR

    1. A197551

      Disconnect the vacuum hose.

    2. Remove the bolt and diesel turbo pressure sensor.

  23. REMOVE NO. 1 GAS FILTER

  24. REMOVE GAS FILTER BRACKET

  25. REMOVE ENGINE COVER BRACKET

  26. REMOVE NO. 2 INTAKE MANIFOLD

  27. REMOVE INTAKE MANIFOLD

  28. REMOVE WATER BY-PASS HOSE

  29. REMOVE OIL COOLER ASSEMBLY

  30. REMOVE NO. 6 WATER BY-PASS HOSE

    A201724
    1. Slide the clip and remove the No. 6 water by-pass hose from the outlet water pipe.

  31. REMOVE NO. 8 WATER BY-PASS HOSE

    A201725
    1. Slide the clip and remove the No. 8 water by-pass hose from the outlet water pipe.

  32. REMOVE NO. 3 WATER BY-PASS PIPE

    1. A263888

      Remove the 2 bolts and No. 3 water by-pass pipe.

    2. Remove the O-ring from the No. 3 water by-pass pipe.

  33. REMOVE NO. 1 TURBO OIL PIPE

    1. A201727

      Remove the 2 union bolts, 2 gaskets and No. 1 turbo oil pipe.

  34. REMOVE NO. 1 OIL COOLER BRACKET

    1. A291655C01
      V100136

      Nut

      Remove the 6 bolts, nut and No. 1 oil cooler bracket.

    2. Remove the 3 gaskets from the No. 1 oil cooler bracket.

  35. REMOVE NO. 1 CYLINDER BLOCK INSULATOR

    1. A263848

      Remove the No. 1 cylinder block insulator from the cylinder block sub-assembly.

  36. REMOVE NO. 2 WATER BY-PASS PIPE

    1. A263849

      Remove the 2 bolts and No. 2 water by-pass pipe from the water inlet housing.

    2. Remove the O-ring from the No. 2 water by-pass pipe.

  37. REMOVE NO. 4 WATER BY-PASS HOSE

    A201736

    Slide the 2 clips and remove the No. 4 water by-pass hose.

  38. REMOVE WATER INLET HOUSING

    1. A142993

      Remove the 3 nuts and water inlet housing.

    2. Remove the gasket from the water inlet housing.

  39. REMOVE FUEL HOSE PROTECTOR

  40. REMOVE FUEL TUBE SUB-ASSEMBLY

  41. REMOVE NO. 3 FUEL HOSE

  42. REMOVE NO. 2 NOZZLE LEAKAGE PIPE

    1. A263891C01
      V100136

      Check Valve

      Remove the check valve and gasket.

    2. Remove the bolt and No. 2 nozzle leakage pipe.

  43. REMOVE NO. 1 NOZZLE LEAKAGE PIPE

  44. REMOVE NO. 1 NOZZLE HOLDER CLAMP

    1. A291656

      Remove the 4 bolts, 4 washers and 4 No. 1 nozzle holder clamps.

  45. REMOVE INJECTOR ASSEMBLY

  46. REMOVE NO. 1 VACUUM SWITCHING VALVE ASSEMBLY

  47. REMOVE VACUUM TRANSMITTING HOSE ASSEMBLY

    1. A263893

      Disengage the 8 clamps and remove the 2 vacuum transmitting hose assemblies.

  48. REMOVE NO. 1 WIRE HARNESS CLAMP BRACKET

    1. A263895

      Remove the bolt and No. 1 wire harness clamp bracket.

  49. REMOVE VENTILATION HOSE

    A263896
    1. Slide the clip and remove the ventilation hose.

  50. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

    1. Remove the oil filler cap sub-assembly.

    2. A263850C01
      V100136

      Nozzle Holder Clamp Seat

      V100137

      Nut

      Remove the 4 nozzle holder clamp seats, 14 bolts, nut and cylinder head cover sub-assembly.

    3. A263851

      Remove the cylinder head cover gasket from the cylinder head cover sub-assembly.

  51. REMOVE OIL PAN SUB-ASSEMBLY

    1. A291657C01
      V100136

      Nut

      Remove the 18 bolts and 2 nuts.

    2. A120816

      Insert the blade of an oil pan seal cutter between the oil pan sub-assembly and cylinder block sub-assembly, cut through the applied sealer and remove the oil pan sub-assembly.

      Note:
      • Do not use the oil pan seal cutter for the area between the oil pan and timing chain cover sub-assembly.

      • Be careful not to damage the contact surfaces of the oil pan sub-assembly.

  52. REMOVE OIL FILTER ELEMENT

  53. REMOVE OIL PRESSURE SWITCHING VALVE ASSEMBLY

  54. REMOVE OIL FILTER BRACKET

    1. A291671

      Remove the 4 bolts and oil filter bracket.

    2. A291672

      Remove the gasket from the oil filter bracket.

  55. REMOVE OIL CHECK VALVE SUB-ASSEMBLY

    1. A294972

      Using a 5 mm hexagon wrench, remove the bolt and oil check valve sub-assembly from the oil filter bracket.

  56. INSPECT OIL CHECK VALVE SUB-ASSEMBLY

    1. A231899C05

      *a

      Ball

      Push the ball of the oil check valve sub-assembly to check if it is stuck.

      If the check valve is stuck, replace the oil check valve sub-assembly.

  57. REMOVE OIL STRAINER SUB-ASSEMBLY

    1. A142992

      Remove the 3 bolts and oil strainer sub-assembly.

    2. Remove the O-ring from the oil strainer sub-assembly.

  58. REMOVE CAMSHAFT POSITION SENSOR

  59. DISCONNECT CRANKSHAFT POSITION SENSOR WIRE HARNESS

    1. A291673

      Remove the clip, bolt and disconnect the crankshaft position sensor wire harness.

  60. REMOVE ENGINE WATER PUMP ASSEMBLY

  61. REMOVE CRANKSHAFT PULLEY

  62. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

    1. A291674C01
      V100136

      Bolt and Seal Washer

      Remove the 13 bolts and seal washer.

    2. A291675C02

      *a

      Protective Tape

      Remove the timing chain cover sub-assembly by prying between the timing chain cover sub-assembly and cylinder head sub-assembly, camshaft housing, cylinder block sub-assembly and stiffening crankcase with a screwdriver as shown in the illustration.

      Note:

      Be careful not to damage the contact surfaces of the cylinder head sub-assembly, camshaft housing, cylinder block sub-assembly, stiffening crankcase and timing chain cover sub-assembly.

      Tip:

      Tape the screwdriver tip before use.

    3. A291676C01

      *1

      Gasket

      *2

      O-Ring

      Remove the gasket and O-ring from the timing chain cover sub-assembly.

  63. REMOVE STRAIGHT SCREW PLUG

    Tip:

    Perform this procedure only when replacement of the straight screw plug.

    1. A201758

      Using a 10 mm socket hexagon wrench, remove the straight screw plug and gasket.

  64. REMOVE FRONT CRANKSHAFT OIL SEAL

    1. A300980C01

      *a

      Protective Tape

      Place the timing chain cover sub-assembly on wooden blocks.

    2. Using a screwdriver, pry out the front crankshaft oil seal.

      Note:

      Do not damage the surface of the oil seal press fit hole.

      Tip:

      Tape the screwdriver tip before use.

  65. REPLACE STUD BOLT

    Tip:

    If a stud bolt is deformed or its threads are damaged, replace it.

    1. A201763C01

      Using an E6 "TORX" wrench, replace the 3 stud bolts.

      3.0 N*m

      31 kgf*cm

      27 in.*lbf