SHIFT AND SELECT LEVER SHAFT REASSEMBLY

PROCEDURE

  1. INSTALL CONTROL SHAFT COVER OIL SEAL

    1. C112481N01

      Using SST and a hammer, install a control shaft cover oil seal to the control shaft cover.

      09307-12010

      Drive in Depth

      0 to 0.5 mm (0 to 0.0197 in.)

    2. Coat a new control shaft cover oil seal lip with MP grease.

  2. INSTALL SHIFT LEVER DAMPER

    1. C202999

      Coat the 2 bolts with sealant.

      Sealant

      Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

    2. Install the shift lever damper to the shift and select lever shaft with the 2 bolts.

      18.6 N*m

      190 kgf*cm

      14 ft.*lbf

  3. INSTALL PIN

    1. C276291

      Install the 2 pins to the No. 1 shift lever inner.

      Drive in Depth

      3.5 to 4.5 mm (0.138 to 0.177 in.)

  4. INSTALL SHIFT GATE PLATE

    1. C276401

      Install the shift gate plate to the No. 1 shift lever inner with the 2 bolts.

      8.5 N*m

      87 kgf*cm

      75 in.*lbf

  5. INSTALL SHIFT AND SELECT LEVER SHAFT

    1. Coat the shift and select lever boot lip and shift and select lever shaft with MP grease.

    2. C276398C01

      *1

      Control Shaft Cover

      *2

      Shift and Select Lever Boot

      *3

      Shift and Select Lever Shaft

      Install the shift and select lever boot and control shaft cover to the shift and select lever shaft.

  6. INSTALL NO. 1 SHIFT LEVER INNER

    1. Coat the shift interlock plate with MP grease.

    2. C276399C01

      *1

      Shift Interlock Plate

      *2

      No. 1 Shift Lever Inner

      *3

      Shift and Select Lever Shaft

      Install the No. 1 shift lever inner and shift interlock plate to the shift and select lever shaft.

    3. C203005

      Using a pin punch and hammer, drive a new slotted spring pin to the No. 1 shift lever inner.

      Drive in Depth

      0.4 to 1.4 mm (0.0157 to 0.0551 in.)

  7. INSTALL SHIFT AND SELECT LEVER ASSEMBLY

    1. C275885

      Align the 4 shift fork shafts as shown in the illustration.

    2. Clean the seal packing attached on the manual transmission case and control shaft cover using a scraper and wire brush. Then remove the oil with non-residue solvent.

      Note:

      Do not scratch the fitting surface.

    3. C113550C07

      *a

      FIPG

      Apply FIPG to the manual transmission case as shown in the illustration.

      FIPG

      Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

      Note:

      Install the parts within 10 minutes of application. Otherwise, the packing (FIPG) material must be removed and reapplied.

    4. Coat the 4 bolts with sealant.

      Sealant

      Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

    5. C202994

      Install the shift and select lever assembly to the manual transmission case with the 4 bolts.

      18.6 N*m

      190 kgf*cm

      14 ft.*lbf

  8. INSTALL SHIFT GATE PIN

    1. C116598

      Coat the shift gate pin with sealant.

      Sealant

      Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

    2. Install the shift gate pin to the manual transmission case.

      30 N*m

      306 kgf*cm

      22 ft.*lbf

  9. INSTALL NO. 2 LOCK BALL ASSEMBLY

    1. C116561

      Coat the No. 2 lock ball assembly with sealant.

      Sealant

      Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

    2. Install the No. 2 lock ball assembly to the manual transmission case.

      29.4 N*m

      300 kgf*cm

      22 ft.*lbf

  10. INSTALL NO. 1 LOCK BALL ASSEMBLY

    1. C116559

      Coat the No. 1 lock ball assembly with sealant.

      Sealant

      Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

    2. Install the No. 1 lock ball assembly to the manual transmission case.

      39.2 N*m

      400 kgf*cm

      29 ft.*lbf

  11. INSTALL NEUTRAL POSITION SWITCH

    1. C202828N02

      Using SST, install a new gasket and the neutral position switch to the manual transmission case.

      09816-30010

      40.2 N*m

      410 kgf*cm

      30 ft.*lbf

  12. INSTALL BACK-UP LIGHT SWITCH ASSEMBLY

    1. C112472N02

      Using SST, install a new gasket and the back-up light switch assembly to the manual transmission case.

      09816-30010

      40.2 N*m

      410 kgf*cm

      30 ft.*lbf

  13. INSTALL NO. 1 SELECTING BELL CRANK DUST COVER

    1. C116207

      Install the No. 1 selecting bell crank dust cover to the selecting bell crank assembly.

  14. INSTALL CONTROL SHIFT LEVER BUSHING

    1. C113636

      Install the control shift lever bushing to the selecting bell crank assembly.

  15. INSTALL SELECTING BELL CRANK ASSEMBLY

    1. C112480

      Coat the 2 bolts with sealant.

      Sealant

      Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

    2. Install the selecting bell crank assembly to the manual transmission case with the 2 bolts.

      20 N*m

      204 kgf*cm

      15 ft.*lbf