ECD SYSTEM, Diagnostic DTC:P2016 and P2017
| DTC Code | DTC Name |
|---|---|
| P2016 | Intake Manifold Runner Position Sensor/Switch Circuit Low Bank 1 |
| P2017 | Intake Manifold Runner Position Sensor/Switch Circuit High Bank 1 |
DESCRIPTION
The swirl control valve is installed to the intake manifold and composed of the swirl flap, swirl flap actuator and swirl flap position sensor.
The position sensor is supplied with a voltage of 5 V by the ECM. The signal of the position sensor is an analogue voltage signal.
The controllable swirl flaps are located in the swirl ports. Depending on the operating range, the swirl flaps are activated with different duty cycles. The further the swirl flaps are closed, the more fresh air is drawn in exclusively through the swirl port. This increases the swirl of the drawn-in fresh air.
In the bottom load and engine speed range the swirl flaps are closed variably according to the operating range.
When the engine speed is approximately 2250 rpm or higher and the fuel injection volume is approximately 30 mg/stk or higher, the swirl flap is fully open.
The position of the swirl flaps is also corrected depending on the ambient pressure. At ambient pressures less than approximately 880 hPa, the swirl flaps tend to be opened further.
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
MIL |
Memory |
|---|---|---|---|---|---|
P2016 |
Intake Manifold Runner Position Sensor/Switch Circuit Low Bank 1 |
Swirl flap position sensor output voltage is 0.2 V or less for 0.22 seconds. (3 trip detection logic) |
|
Comes on |
DTC stored |
P2017 |
Intake Manifold Runner Position Sensor/Switch Circuit High Bank 1 |
Swirl flap position sensor output voltage is 4.85 V or more for 0.22 seconds. (3 trip detection logic) |
|
Comes on |
DTC stored |
DTC No. |
Data List |
|---|---|
P2016 P2017 |
Swirl Valve Actuator Position |
WIRING DIAGRAM
CAUTION / NOTICE / HINT
When replacing the ECM, the ECM needs registration and initialization.
After replacing the swirl control valve, the ECM needs initialization.
When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
PROCEDURE
PERFORM ACTIVE TEST USING GTS (ACTUATOR TEST OF SWIRL FLAP)
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Actuator Test of Swirl Flap / Data List / Swirl Valve Actuator Position.
Powertrain > Engine and ECT > Active Test
Active Test Display
Actuator Test of Swirl Flap
Data List Display
Swirl Valve Actuator Position
OK
The value of "Swirl Valve Actuator Position" changes according to the amount "Actuator Test of Swirl Flap" is operated, and the swirl flap operates smoothly.
Result
Proceed to
OK
NG
OK CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIREDClick here
CHECK HARNESS AND CONNECTOR (SWIRL CONTROL VALVE - ECM)
Disconnect the swirl control valve connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection
Condition
Specified Condition
B238-3 (SCV+) - B220-49 (IA1+)
Always
Below 1 Ω
B238-4 (SCV-) - B220-19 (IA1-)
Always
Below 1 Ω
B238-5 (VCX) - B220-72 (VAC1)
Always
Below 1 Ω
B238-1 (VSX) - B220-87 (IAC1)
Always
Below 1 Ω
B238-2 (E2X) - B220-119 (EAC1)
Always
Below 1 Ω
B238-3 (SCV+) or B220-49 (IA1+) - Body ground
Always
10 kΩ or higher
B238-4 (SCV-) or B220-19 (IA1-) - Body ground
Always
10 kΩ or higher
B238-5 (VCX) or B220-72 (VAC1) - Body ground
Always
10 kΩ or higher
B238-1 (VSX) or B220-87 (IAC1) - Body ground
Always
10 kΩ or higher
Result
Proceed to
OK
NG
NG REPAIR OR REPLACE HARNESS OR CONNECTORClick here
CHECK HARNESS AND CONNECTOR (VC VOLTAGE)
*a
Front view of wire harness connector
(to Swirl Control Valve)
Disconnect the swirl control valve connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
Standard Voltage
Tester Connection
Switch Condition
Specified Condition
B238-5 (VCX) - B238-2 (E2X)
Ignition switch ON
4.5 to 5.5 V
Result
Proceed to
OK
NG
NG REPLACE ECMClick here
REPLACE SWIRL CONTROL VALVE
Replace the swirl control valve.
Perform the swirl valve learning value reset.
Result
Proceed to
NEXT
CHECK WHETHER DTC OUTPUT RECURS (DTC P2016 AND/OR P2017)
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Powertrain > Engine and ECT > Clear DTCs
Turn the ignition switch off and wait for 60 seconds or more [A].
Perform road test [B].
Repeat [A] and [B] for the number of trips detected.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Powertrain > Engine and ECT > Trouble Codes
Read the DTCs.
Result
Result
Proceed to
No DTC output
A
DTC P2016 and/or P2017
B
A END
B REPLACE ECMClick here
REPLACE ECM
Replace the ECM.
Result
Proceed to
NEXT
NEXT CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIREDClick here
REPAIR OR REPLACE HARNESS OR CONNECTOR
Repair or replace the harness or connector.
Result
Proceed to
NEXT
CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Powertrain > Engine and ECT > Clear DTCs
Turn the ignition switch off and wait for 60 seconds or more [A].
Perform road test [B].
Repeat [A] and [B] for the number of trips detected.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Powertrain > Engine and ECT > Trouble Codes
Confirm that the DTC is not output again.
Result
Proceed to
NEXT
NEXT END