BRAKE ACTUATOR INSTALLATION

PROCEDURE

  1. INSTALL BRAKE ACTUATOR ASSEMBLY

    1. for Type A Brake Actuator Assembly:

      1. C269616N01

        Install the brake actuator assembly to the brake actuator bracket assembly with the bolt and 2 new nuts.

        Bolt

        5.4 N*m

        55 kgf*cm

        48 in.*lbf

        Nut

        7.5 N*m

        76 kgf*cm

        66 in.*lbf

        Note:
        • Do not remove the hole plugs of a new brake actuator assembly before connecting the brake lines because the brake actuator assembly is filled with brake fluid.

        • Do not hold the brake actuator assembly by the connector.

        • Tighten the bolt and 2 nuts in the order shown in the illustration.

    2. for Type B Brake Actuator Assembly:

      1. C287022N01

        Install the brake actuator assembly to the brake actuator bracket assembly with the 3 bolts.

        5.4 N*m

        55 kgf*cm

        48 in.*lbf

        Note:
        • Do not remove the hole plugs of a new brake actuator assembly before connecting the brake lines because the brake actuator assembly is filled with brake fluid.

        • Do not hold the brake actuator assembly by the connector.

        • Tighten the 3 bolts in the order shown in the illustration.

  2. INSTALL BRAKE ACTUATOR WITH BRACKET

    1. for Type A Brake Actuator Assembly:

      1. C269615N01

        Install the brake actuator with bracket to the vehicle body with 3 new nuts.

        19 N*m

        194 kgf*cm

        14 ft.*lbf

        Note:
        • Do not damage the brake lines, fuel lines or wire harness.

        • Tighten the 3 nuts in the order shown in the illustration.

      2. Engage each clamp to install the No. 2 fuel tube clamp and front No. 4 brake tube to the brake actuator bracket assembly.

        Note:

        Do not damage the brake lines or fuel lines.

      3. C269612C01

        *a

        for LHD:

        From 1st Chamber of Master Cylinder Sub-assembly

        for RHD:

        From 2nd Chamber of Master Cylinder Sub-assembly

        *b

        for LHD:

        From 2nd Chamber of Master Cylinder Sub-assembly

        for RHD:

        From 1st Chamber of Master Cylinder Sub-assembly

        *c

        To Front Wheel Cylinder Assembly RH

        *d

        To Rear Wheel Cylinder Assembly LH

        *e

        To Rear Wheel Cylinder Assembly RH

        *f

        To Front Wheel Cylinder Assembly LH

        Temporarily tighten each brake line to the correct position on the brake actuator assembly as shown in the illustration.

      4. Using a union nut wrench, fully tighten each brake line.

        *a, *b (w/o VSC)

        15.2 N*m

        155 kgf*cm

        11 ft.*lbf

        *a, *b (w/ VSC)

        19.5 N*m

        199 kgf*cm

        14 ft.*lbf

        *c, *d, *e, *f

        15.2 N*m

        155 kgf*cm

        11 ft.*lbf

        Note:

        Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench.

        Click here

      5. C269614N02

        Engage the clamp to install the wire harness to the brake actuator bracket assembly.

      6. Connect the connector to the brake actuator assembly and disengage the claw (b).

      7. Pull the lever down and engage the claw (a) to engage the connector lock.

        Note:
        • Make sure that the connector is locked securely.

        • Make sure that the actuator connector can be connected smoothly. Do not allow water, oil or dirt to enter the connector.

    2. for Type B Brake Actuator Assembly:

      1. C287021N01

        Install the brake actuator with bracket to the vehicle body with the 3 nuts.

        19 N*m

        194 kgf*cm

        14 ft.*lbf

        Note:
        • Do not damage the brake lines, fuel lines or wire harness.

        • Tighten the 3 nuts in the order shown in the illustration.

      2. Engage each clamp to install the No. 2 fuel tube clamp and front No. 4 brake tube to the brake actuator bracket assembly.

        Note:

        Do not damage the brake lines or fuel lines.

      3. C287020C01

        *a

        From 1st Chamber of Master Cylinder Sub-assembly

        *b

        From 2nd Chamber of Master Cylinder Sub-assembly

        *c

        To Front Wheel Cylinder Assembly LH

        *d

        To Rear Wheel Cylinder Assembly RH

        *e

        To Rear Wheel Cylinder Assembly LH

        *f

        To Front Wheel Cylinder Assembly RH

        Temporarily tighten each brake line to the correct position on the brake actuator assembly as shown in the illustration.

      4. Using a union nut wrench, fully tighten each brake line.

        15.2 N*m

        155 kgf*cm

        11 ft.*lbf

        Note:

        Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench.

        Click here

      5. C287019C01
        V100135

        Connect

        V100136

        Lock

        Connect the connector to the brake actuator assembly and lock the lock lever.

        Note:
        • Make sure that the connector is locked securely.

        • Make sure that the actuator connector can be connected smoothly. Do not allow water, oil or dirt to enter the connector.

    3. Connect the connector to the ECM.

      for 1NR-FE:Click here

      for 1ZR-FE:Click here

      for 1ZR-FAE:Click here

      for 2ZR-FE:Click here

  3. INSTALL BRAKE ACTUATOR COVER (for 1AD-FTV, 1ND-TV with VSC)

    1. Raise the claw of a new brake actuator cover, insert the pin into the hole and engage the claw to install it to the brake actuator assembly.

      C287025C01

      *a

      Claw

      *b

      Pin

  4. INSTALL AIR CLEANER BRACKET (for 1AD-FTV, 1ND-TV)

    1. Install the air cleaner bracket with the 3 bolts.

      7.0 N*m

      71 kgf*cm

      62 in.*lbf

  5. INSTALL FUEL FILTER SUPPORT (for 1AD-FTV, 1ND-TV)

    1. Install the fuel filter support with the 3 bolts.

      17.5 N*m

      178 kgf*cm

      13 ft.*lbf

    2. Engage the wire harness clamp to the fuel filter support.

  6. INSTALL GLOW PLUG RELAY ASSEMBLY (for 1AD-FTV, 1ND-TV)

    1. Install the glow plug relay assembly to the fuel filter support with the bolt.

      11 N*m

      112 kgf*cm

      8 ft.*lbf

    2. Connect the wire harness clamp to the fuel filter support.

  7. CONNECT WIRE HARNESS (for 1AD-FTV, 1ND-TV)

    1. Connect the ECM connector to the ECM.

      for 1AD-FTV:Click here

      for 1ND-TV:Click here

    2. Connect the 3 wire harness clamps to the fuel filter support.

  8. INSTALL FUEL FILTER ASSEMBLY (for 1AD-FTV, 1ND-TV)

    for 1AD-FTV:Click here

    for 1ND-TV:Click here

  9. INSTALL AIR CLEANER CASE SUB-ASSEMBLY (for 1NR-FE)

  10. INSTALL AIR CLEANER CAP SUB-ASSEMBLY (for 1NR-FE)

  11. INSTALL NO. 1 ENGINE COVER (for 1NR-FE)

  12. INSTALL AIR CLEANER CASE SUB-ASSEMBLY (for 1ZR-FE)

  13. INSTALL AIR CLEANER CAP SUB-ASSEMBLY (for 1ZR-FE)

  14. INSTALL NO. 2 CYLINDER HEAD COVER (for 1ZR-FE)

  15. INSTALL AIR CLEANER CASE SUB-ASSEMBLY (for 1ZR-FAE)

  16. INSTALL AIR CLEANER CAP SUB-ASSEMBLY (for 1ZR-FAE)

  17. INSTALL NO. 2 CYLINDER HEAD COVER (for 1ZR-FAE)

  18. INSTALL AIR CLEANER CASE SUB-ASSEMBLY (for 2ZR-FE)

  19. INSTALL AIR CLEANER CAP SUB-ASSEMBLY (for 2ZR-FE)

  20. INSTALL NO. 2 CYLINDER HEAD COVER (for 2ZR-FE)

  21. INSTALL AIR CLEANER CASE SUB-ASSEMBLY (for 1AD-FTV)

  22. INSTALL AIR CLEANER CAP SUB-ASSEMBLY (for 1AD-FTV)

  23. INSTALL NO. 1 ENGINE COVER (for 1AD-FTV)

  24. INSTALL AIR CLEANER CASE SUB-ASSEMBLY (for 1ND-TV)

  25. INSTALL AIR CLEANER CAP SUB-ASSEMBLY (for 1ND-TV)

  26. INSTALL NO. 1 ENGINE COVER (for 1ND-TV with No. 1 Engine Cover)

  27. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  28. BLEED AIR FROM FUEL SYSTEM (for 1AD-FTV, 1ND-TV)

    for 1AD-FTV:Click here

    for 1ND-TV:Click here

  29. INSPECT FOR FUEL LEAK (for 1AD-FTV, 1ND-TV)

    for 1AD-FTV:Click here

    for 1ND-TV:Click here

  30. BLEED BRAKE SYSTEM

  31. INSPECT BRAKE ACTUATOR USING GTS

  32. PERFORM SYSTEM VARIANT LEARNING (w/ VSC)

  33. CHECK FOR AND CLEAR DTCS

    w/o VSC (for Type A):Click here

    w/o VSC (for Type B):Click here

    w/ VSC:Click here