ECD SYSTEM, Diagnostic DTC:P2000
| DTC Code | DTC Name |
|---|---|
| P2000 | NOx Adsorber Efficiency Below Threshold Bank 1 |
DESCRIPTION
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
MIL |
Memory |
|---|---|---|---|---|---|
P2000 |
NOx Adsorber Efficiency Below Threshold Bank 1 |
The regeneration throughput of the catalytic converter is less than the standard value. (3 trip detection logic) |
|
Comes on |
DTC stored |
CAUTION / NOTICE / HINT
After replacing the air fuel ratio sensor, the ECM needs initialization.
After replacing the exhaust manifold converter sub-assembly (catalytic converter), the ECM needs initialization.
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
PROCEDURE
CHECK AIR FUEL RATIO SENSOR (FOR SENSOR 1)
Check the installation condition of the air fuel ratio sensor (for sensor 1).
OK
Air fuel ratio sensor is correctly installed.
Result
Proceed to
OK
NG
NG REPAIR AIR FUEL RATIO SENSOR (FOR SENSOR 1)Click here
CHECK AIR FUEL RATIO SENSOR (FOR SENSOR 1)
Check for soot deposits in the air fuel ratio sensor (for sensor 1).
OK
No soot deposits.
Result
Proceed to
OK
NG
NG REPAIR AIR FUEL RATIO SENSOR (FOR SENSOR 1)Click here
REPLACE AIR FUEL RATIO SENSOR (FOR SENSOR 1)
Replace the air fuel ratio sensor (for sensor 1).
Perform the O2 sensor learning value reset.
Result
Proceed to
NEXT
CHECK WHETHER DTC OUTPUT RECURS (DTC P2000)
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Powertrain > Engine and ECT > Clear DTCs
Turn the ignition switch off and wait for 60 seconds or more [A].
Perform road test [B].
Repeat [A] and [B] for the number of trips detected.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Powertrain > Engine and ECT > Trouble Codes
Read the DTCs.
Result
Result
Result
Proceed to
No DTC output
No DTC output
A
DTC P2000
DTC P2000
B
A END
REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (DPF CATALYTIC CONVERTER)
Replace the exhaust manifold converter sub-assembly (catalytic converter).
Perform DPF history information reset and NOx storage catalyst learning value reset.
Result
Proceed to
NEXT
NEXT CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIREDClick here
REPAIR AIR FUEL RATIO SENSOR (FOR SENSOR 1)
Remove any soot deposits from the air fuel ratio sensor.
Result
Proceed to
NEXT
NEXT CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIREDClick here
REPAIR AIR FUEL RATIO SENSOR (FOR SENSOR 1)
Reinstall the air fuel ratio sensor (for sensor 1).
Result
Proceed to
NEXT
CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Powertrain > Engine and ECT > Clear DTCs
Turn the ignition switch off and wait for 60 seconds or more [A].
Perform road test [B].
Repeat [A] and [B] for the number of trips detected.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Powertrain > Engine and ECT > Trouble Codes
Confirm that the DTC is not output again.
Result
Proceed to
NEXT
NEXT END