ECD SYSTEM, Diagnostic DTC:P0606,P060A,P060C,P062F,P064D and P1607

DTC Code DTC Name
P0606 Control Module Processor
P060A Internal Control Module Monitoring Processor Performance
P060C Internal Control Module Main Processor Performance
P062F Internal Control Module EEPROM Error
P064D Internal Control Module O2 Sensor Processor Performance Bank 1
P1607 System State Logical Error Detection

DESCRIPTION

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Memory

P0606

Control Module Processor

ECM internal error.

(1 trip detection logic)

ECM

Comes on

DTC stored

P060A

Internal Control Module Monitoring Processor Performance

ECM internal error.

(1 trip detection logic)

ECM

Comes on

DTC stored

P060C

Internal Control Module Main Processor Performance

ECM internal error.

(1 trip detection logic)

ECM

Comes on

DTC stored

P062F

Internal Control Module EEPROM Error

ECM internal error.

(1 trip detection logic)

ECM

Comes on

DTC stored

P064D

Internal Control Module O2 Sensor Processor Performance Bank 1

Decrease in ECM supply voltage resulting in insufficient voltage to air fuel ratio sensor circuit.

(3 trip detection logic)

ECM

Does not come on

DTC stored

P1607

System State Logical Error Detection

ECM internal error.

(1 trip detection logic)

ECM

Does not come on

DTC stored

CAUTION / NOTICE / HINT

Note:

When replacing the ECM, the ECM needs registration and initialization.

Click here

Tip:
  • When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registration for the "Learning Values Write" function by following the instructions shown on the GTS display.

  • Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE

  1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0606, P060A, P060C, P062F, P064D, P1607)

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

      Powertrain > Engine and ECT > Trouble Codes

    4. Read the DTCs.

      Result

      Result

      Proceed to

      DTC P0606, P060A, P060C, P062F, P064D and/or P1607

      A

      DTC P0606, P060A, P060C, P062F, P064D and/or P1607 and other DTCs

      B

      Tip:
      • When DTC P062D is output, DTC P060A may also be output on the next trip. Therefore, when DTC P062D and P060A are output simultaneously, perform troubleshooting for DTC P062D first.

      • If any DTCs other than P0606, P060A, P060C, P062F, P064D and/or P1607 are output, troubleshoot those DTCs first.

    B

    GO TO DTC CHART

    A
  2. REPLACE ECM

    1. Replace the ECM.

      Click here

    Result

    Proceed to

    NEXT

    NEXT
  3. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs.

      Powertrain > Engine and ECT > Clear DTCs

    4. Turn the ignition switch off and wait for 60 seconds or more [A].

    5. Perform road test [B].

    6. Repeat [A] and [B] for the number of trips detected.

    7. Enter the following menus: Engine and ECT / Trouble Codes.

      Powertrain > Engine and ECT > Trouble Codes

    8. Confirm that the DTC is not output again.

    Result

    Proceed to

    NEXT

    NEXT

    END