AUDIO AND VISUAL SYSTEM(for Sedan Radio and Display Type), Diagnostic DTC:B15C3

DTC Code DTC Name
B15C3 Speaker Output Short

DESCRIPTION

This DTC is stored when a malfunction occurs in the speakers.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

B15C3

Speaker Output Short

A short is detected in the speaker output circuit

  • Harness or connector

  • Speaker

  • Radio and display receiver assembly

  • Telematics transceiver*

  • *: w/ Manual (SOS) Switch

WIRING DIAGRAM

E348132E01

PROCEDURE

  1. CHECK MODEL

    1. Choose the model to be inspected.

      Result

      Result

      Proceed to

      w/o Manual (SOS) Switch

      A

      w/ Manual (SOS) Switch

      B

    B

    CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY, TELEMATICS TRANSCEIVER OR SPEAKERS - BODY GROUND)Click here

    A
  2. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BODY GROUND)

    1. Disconnect the E1 and E2 radio and display receiver assembly connectors.

    2. Disconnect the G4 and H5 front No. 2 speaker assembly connectors.

    3. Disconnect the L79 and L80 rear speaker assembly connectors.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      E1-1 (FR+) or G4-4 (TWR+) - Body ground

      Always

      10 kΩ or higher

      E1-5 (FR-) or G4-2 (TWR-) - Body ground

      Always

      10 kΩ or higher

      E1-2 (FL+) or H5-4 (TWL+) - Body ground

      Always

      10 kΩ or higher

      E1-6 (FL-) or H5-2 (TWL-) - Body ground

      Always

      10 kΩ or higher

      E2-1 (RR+) or L79-1 - Body ground

      Always

      10 kΩ or higher

      E2-3 (RR-) or L79-2 - Body ground

      Always

      10 kΩ or higher

      E2-2 (RL+) or L80-1 - Body ground

      Always

      10 kΩ or higher

      E2-6 (RL-) or L80-2 - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK
  3. CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER ASSEMBLY - BODY GROUND)

    1. Disconnect the G1 and H1 front No. 1 speaker assembly connectors.

    2. Disconnect the G4 and H5 front No. 2 speaker assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      G4-3 (+) or G1-1 - Body ground

      Always

      10 kΩ or higher

      G4-1 (-) or G1-2 - Body ground

      Always

      10 kΩ or higher

      H5-3 (+) or H1-1 - Body ground

      Always

      10 kΩ or higher

      H5-1 (-) or H1-2 - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK
  4. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

    1. Remove the front No. 1 speaker assembly.

      Click here

    2. E219303C30

      *a

      Component without harness connected

      (Front No. 1 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      1 - 2

      Always

      3.2 to 4.8 Ω

    Result

    Proceed to

    OK

    NG

    NG

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

    OK
  5. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

    1. Remove the front No. 2 speaker assembly.

      Click here

    2. E226097C11

      *A

      for RH

      *B

      for LH

      *a

      Component without harness connected

      (Front No. 2 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      4 (TWR+) - 2 (TWR-)

      Always

      10 kΩ or higher

      3 (+) - 4 (TWR+)

      Always

      Below 1 Ω

      1 (-) - 2 (TWR-)

      Always

      Below 1 Ω

      4 (TWL+) - 2 (TWL-)

      Always

      10 kΩ or higher

      3 (+) - 4 (TWL+)

      Always

      Below 1 Ω

      1 (-) - 2 (TWL-)

      Always

      Below 1 Ω

    Result

    Proceed to

    OK

    NG

    NG

    REPLACE FRONT NO. 2 SPEAKER ASSEMBLY

    OK
  6. REPLACE FRONT NO. 2 SPEAKER ASSEMBLY

    1. Replace the front No. 2 speaker assembly.

      Click here

    2. Clear the DTCs.

      Click here

      Body Electrical > Navigation System > Clear DTCs

    3. Recheck for DTCs and check that no DTCs are output.

      Body Electrical > Navigation System > Trouble Codes

      OK

      No DTCs are output.

      Tip:
      • Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.

      • When there is a possibility that either the right or left front No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.

      • Perform the above inspection on both LH and RH sides.

    Result

    Proceed to

    OK

    NG

    OK

    END

    NG
  7. INSPECT REAR SPEAKER ASSEMBLY

    1. Remove the rear speaker assembly.

      Click here

    2. E219303C30

      *a

      Component without harness connected

      (Rear Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      1 - 2

      Always

      3.2 to 4.8 Ω

    Result

    Proceed to

    OK

    NG

    OK

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

    NG

    REPLACE REAR SPEAKER ASSEMBLY

  8. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY, TELEMATICS TRANSCEIVER OR SPEAKERS - BODY GROUND)

    1. Disconnect the E1 and E2 radio and display receiver assembly connectors.

    2. Disconnect the E143 telematics transceiver connector.

    3. Disconnect the H5 front No. 2 speaker assembly LH connector.

    4. Disconnect the L79 and L80 rear speaker assembly connectors.

    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      E1-1 (FR+) or E143-2 (SPI+) - Body ground

      Always

      10 kΩ or higher

      E1-5 (FR-) or E143-3 (SPI-) - Body ground

      Always

      10 kΩ or higher

      E1-2 (FL+) or H5-4 (TWL+) - Body ground

      Always

      10 kΩ or higher

      E1-6 (FL-) or H5-2 (TWL-) - Body ground

      Always

      10 kΩ or higher

      E2-1 (RR+) or L79-1 - Body ground

      Always

      10 kΩ or higher

      E2-3 (RR-) or L79-2 - Body ground

      Always

      10 kΩ or higher

      E2-2 (RL+) or L80-1 - Body ground

      Always

      10 kΩ or higher

      E2-6 (RL-) or L80-2 - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK
  9. INSPECT TELEMATICS TRANSCEIVER

    1. Remove the telematics transceiver.

      Click here

    2. E169849C05

      *a

      Component without harness connected

      (Telematics Transceiver)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      2 (SPI+) - 5 (SPO+)

      Always

      Below 1 Ω

      3 (SPI-) - 6 (SPO-)

      Always

      Below 1 Ω

      2 (SPI+) - 3 (SPI-)

      Always

      10 kΩ or higher

      5 (SPO+) - 6 (SPO-)

      Always

      10 kΩ or higher

      2 (SPI+) or 5 (SPO+) - Body ground

      Always

      10 kΩ or higher

      3 (SPI-) or 6 (SPO-) - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG

    NG

    REPLACE TELEMATICS TRANSCEIVER

    OK
  10. CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER ASSEMBLY RH OR TELEMATICS TRANSCEIVER - BODY GROUND)

    1. Disconnect the G4 front No. 2 speaker assembly RH connector.

    2. Disconnect the E143 telematics transceiver connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      G4-4 (TWR+) or E143-5 (SPO+) - Body ground

      Always

      10 kΩ or higher

      G4-2 (TWR-) or E143-6 (SPO-) - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK
  11. CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER ASSEMBLY - BODY GROUND)

    1. Disconnect the G1 and H1 front No. 1 speaker assembly connectors.

    2. Disconnect the G4 and H5 front No. 2 speaker assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      G4-3 (+) or G1-1 - Body ground

      Always

      10 kΩ or higher

      G4-1 (-) or G1-2 - Body ground

      Always

      10 kΩ or higher

      H5-3 (+) or H1-1 - Body ground

      Always

      10 kΩ or higher

      H5-1 (-) or H1-2 - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK
  12. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

    1. Remove the front No. 1 speaker assembly.

      Click here

    2. E219303C30

      *a

      Component without harness connected

      (Front No. 1 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      1 - 2

      Always

      3.2 to 4.8 Ω

    Result

    Proceed to

    OK

    NG

    NG

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

    OK
  13. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

    1. Remove the front No. 2 speaker assembly.

      Click here

    2. E226097C11

      *A

      for RH

      *B

      for LH

      *a

      Component without harness connected

      (Front No. 2 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      4 (TWR+) - 2 (TWR-)

      Always

      10 kΩ or higher

      3 (+) - 4 (TWR+)

      Always

      Below 1 Ω

      1 (-) - 2 (TWR-)

      Always

      Below 1 Ω

      4 (TWL+) - 2 (TWL-)

      Always

      10 kΩ or higher

      3 (+) - 4 (TWL+)

      Always

      Below 1 Ω

      1 (-) - 2 (TWL-)

      Always

      Below 1 Ω

    Result

    Proceed to

    OK

    NG

    NG

    REPLACE FRONT NO. 2 SPEAKER ASSEMBLY

    OK
  14. REPLACE FRONT NO. 2 SPEAKER ASSEMBLY

    1. Replace the front No. 2 speaker assembly.

      Click here

    2. Clear the DTCs.

      Click here

      Body Electrical > Navigation System > Clear DTCs

    3. Recheck for DTCs and check that no DTCs are output.

      Body Electrical > Navigation System > Trouble Codes

      OK

      No DTCs are output.

      Tip:
      • Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.

      • When there is a possibility that either the right or left front No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.

      • Perform the above inspection on both LH and RH sides.

    Result

    Proceed to

    OK

    NG

    OK

    END

    NG
  15. INSPECT REAR SPEAKER ASSEMBLY

    1. Remove the rear speaker assembly.

      Click here

    2. E219303C30

      *a

      Component without harness connected

      (Rear Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      1 - 2

      Always

      3.2 to 4.8 Ω

    Result

    Proceed to

    OK

    NG

    OK

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

    NG

    REPLACE REAR SPEAKER ASSEMBLY