ECD SYSTEM FREEZE FRAME DATA

  1. DESCRIPTION

    • The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the air fuel ratio was lean or rich, as well as the other data recorded at the time of a malfunction.

      Tip:

      If it is impossible to duplicate the problem even though a DTC is stored, confirm the freeze frame data.

    • A103809E77

      The ECM records engine conditions in the form of freeze frame data every 0.5 seconds. Using the GTS, 5 separate sets of freeze frame data can be checked.

      • 3 data sets from before the DTC was stored

      • 1 data set from when the DTC was stored

      • 1 data set from after the DTC was stored

      • These data sets can be used to simulate the condition of the vehicle from around the time of the occurrence of the malfunction. The data may assist in identifying the cause of the malfunction, and in judging whether it was temporary or not.

  2. LIST OF FREEZE FRAME DATA

Powertrain > Engine and ECT

Tester Display

Measurement Item

Diagnostic Note

Vehicle Speed

Vehicle speed

The speed indicated on the speedometer.

Target Idle Engine Speed

Target idling speed

-

Engine Speed

Engine speed

-

Calculate Load

Calculated load

The load calculated by the ECM.

MAF

Mass air flow volume

If approximately 0.0 gm/sec:

  • The mass air flow meter assembly power source circuit is open or shorted.

  • The VG circuit is open or shorted.

  • The E2G circuit is open.

Atmosphere Pressure

Atmospheric pressure

-

MAP

Absolute pressure inside intake manifold

-

Coolant Temp

Engine coolant temperature

If -40°C (-40°F), the sensor circuit is open.

If 140°C (284°F), the sensor circuit is shorted.

Intake Air

Intake air temperature

If -40°C (-40°F), the sensor circuit is open.

If 140°C (284°F), the sensor circuit is shorted.

Intake Air Temp (Turbo)

Intake air temperature after intercooler

If -40°C (-40°F), the sensor circuit is open.

If 190°C (374°F), the sensor circuit is shorted.

Engine Run Time

Accumulated engine running time

-

Initial Engine Coolant Temp

Engine coolant temperature at engine start

-

Initial Intake Air Temp

Intake air temperature at engine start

-

Battery Voltage

Battery voltage

-

Glow Control Unit Duty

Glow plug controller duty

-

Glow Indicator Supported

Glow indicator supported

-

Glow Indicator

Glow indicator

-

Eng Oil Press Switch Valve

Oil pressure switching valve assembly

-

Engine Oil Pressure

Engine oil pressure

-

Accel Position

Accelerator pedal sensor assembly

-

Accel Sens. No.1 Volt %

Accelerator pedal position No. 1 output voltage

-

Accel Sens. No.2 Volt %

Accelerator pedal position No. 2 output voltage

-

Target Throttle Position

Target throttle position

-

Actual Throttle Position

Actual throttle position

-

Diesel Throttle Learn Status

Diesel throttle learning status

-

Throttle Sensor Volt %

Throttle position sensor output voltage

-

Throttle Motor DUTY

Throttle actuator

-

Injection Volume

Injection volume

-

Inj. FB Vol. for Idle

Injection feedback value for idle speed control

-

Inj Vol Feedback Learning

Injection volume feedback learned value

-

Injection Feedback Val #1

Injection volume correction for cylinder 1

-

Injection Feedback Val #2

Injection volume correction for cylinder 2

-

Injection Feedback Val #3

Injection volume correction for cylinder 3

-

Injection Feedback Val #4

Injection volume correction for cylinder 4

-

Pilot 1 Injection Period

Pilot 1 injection period

-

Pilot 2 Injection Period

Pilot 2 injection period

-

Main Injection Period

Main injection period

-

After Injection Period

Post injection period

-

Pilot 1 Injection Timing

Pilot 1 injection timing

-

Pilot 2 Injection Timing

Pilot 2 injection timing

-

Main Injection Timing

Main injection timing

-

After Injection Timing

Post injection timing

-

Injector Memory Error

State of injector related EEPROM information stored in ECM

This item is used for troubleshooting when DTC P062F is stored.

Reju Pilot Quantity Learning

Pilot quantity learning prohibition

The status is only displayed while performing "Pilot Quantity Learning".

Pilot Quantity Learning

Pilot quantity learning status

The status is only displayed while performing "Pilot Quantity Learning".

Target Common Rail Pressure

Target common rail pressure

-

Fuel Press

Fuel pressure

-

Fuel Temperature

Fuel temperature

-

Fuel Return Temp

Fuel return temperature

-

Target Pump SCV Current

Final pump current target value

-

Pump SCV Learning Value

Pump current learned value

-

Pressure Discharge Valve

Pressure discharge valve operation prohibition

-

AF Lambda B1S1

Lambda equivalent ratio

-

AFS Voltage B1S1

Air fuel ratio sensor output voltage

-

AFS Current B1S1

Air fuel ratio sensor output current

-

Target EGR Position

Target EGR valve position

-

Actual EGR Valve Pos.

Actual EGR valve position

-

EGR Motor Duty #1

EGR motor duty ratio

-

EGR Close Lrn. Val.

EGR valve fully closed position learned value

-

EGR Close Lrn. Status

EGR valve fully closed position learning status

-

EGR Operation Prohibit

EGR operation prohibition

-

EGR Cooler Bypass VSV

No. 1 vacuum switching valve assembly (for EGR cooler) status

-

EGR Cooler Bypass Position

EGR cooler bypass position

-

Target Booster Pressure

Target booster pressure

-

VN Turbo Command

VN turbo command

-

Actual VN Position

Actual VN turbo position

-

VN Position Sensor Out

VN position sensor output voltage

-

VN Motor Duty

VN turbo motor duty

-

VN Close Learn Value

VN turbo fully closed position learned value

-

VN Close Learn Status

VN turbo fully closed position learning status

-

Exhaust Temperature B1S1 Supported

Status of the exhaust temperature B1S1 supported

-

Exhaust Temperature B1S1

Exhaust temperature sensor (B1S1)

If 0°C (32°F), sensor circuit is open

If 1000°C (1832°F), sensor circuit is shorted

Exhaust Temperature B1S2 Supported

Status of the exhaust temperature B1S2 supported

-

Exhaust Temperature B1S2

No. 2 exhaust temperature sensor (B1S2)

If 0°C (32°F), sensor circuit is open

If 1000°C (1832°F), sensor circuit is shorted

Exhaust Temperature B1S3 Supported

Status of the exhaust temperature B1S3 supported

-

Exhaust Temperature B1S3

No. 3 exhaust temperature sensor (B1S3)

If 0°C (32°F), sensor circuit is open

If 1000°C (1832°F), sensor circuit is shorted

DPF Differential Pressure

DPF differential pressure

-

Catalyst Differential Press

Standardized DPF differential pressure

-

Exhaust Fuel Addition FB

Exhaust fuel addition correction value

-

DPF Thermal Deteriorate

DPF thermal deterioration

-

DPF No Activate

DPF operation

-

DPF PM Block

DPF PM block

-

Catalyst Memory Error

EEPROM malfunction for catalyst

This item is used for troubleshooting when DTC P062F is stored.

PM Accumulation Ratio

PM accumulation ratio

-

Starter Signal

Starter signal

-

Clutch Switch

Clutch switch assembly

-

Reverse Switch

Reverse switch

-

Stop Light Switch

Stop light switch assembly

-

Shift Indication Enable

Shift indication enable

-

A/C Signal

Air conditioning signal

-

Immobiliser Communication

Immobiliser communication

-

Time after DTC Cleared

Cumulative time after DTC cleared

-

Distance from DTC Cleared

Accumulated distance after DTC cleared

-

Warmup Cycle Cleared DTC

Warmup cycles after DTC cleared

-

TC and TE1

TC and TE1 terminals of DLC3

-

Engine Start Time

Engine start time

This item is used for troubleshooting when DTC P1604 is stored.

Engine Speed (Starter Off)

Engine speed when starter off

This item is used for troubleshooting when DTC P1604 is stored.

Starter Count

Number of times starter turned on after ignition switch ON

This item is used for troubleshooting when DTC P1604 is stored.

Run Dist of Previous Trip

Distance driven during previous trip

This item is used for troubleshooting when DTC P1604 is stored.

Glow Request Lighting Time

Glow indicator request lighting time

This item is used for troubleshooting when DTC P1604 is stored.

IG-ON Time

Ignition switch ON time before engine start

This item is used for troubleshooting when DTC P1604 is stored.

MAF Low

Mass air flow low

This item is used for troubleshooting when DTC P1608 is stored.

Boost Pressure Low

Boost pressure low

This item is used for troubleshooting when DTC P1608 is stored.

Common Rail Pressure Low

Common rail pressure low

This item is used for troubleshooting when DTC P1608 is stored.

Engine Coolant Temp High

Engine coolant temperature high

This item is used for troubleshooting when DTC P1608 is stored.

MAF/Estimate MAF Ratio

Indicates the ratio of estimated intake air volume and the actual intake air volume

This item is used for troubleshooting when DTC P1608 is stored.

Rough Idle #1

Rough idle status of cylinder 1

This item is used for troubleshooting when DTC P1605 is stored.

Rough Idle #2

Rough idle status of cylinder 2

This item is used for troubleshooting when DTC P1605 is stored.

Rough Idle #3

Rough idle status of cylinder 3

This item is used for troubleshooting when DTC P1605 is stored.

Rough Idle #4

Rough idle status of cylinder 4

This item is used for troubleshooting when DTC P1605 is stored.

Electric Duty Feedback Value

Electric load feedback value

-

A/C Duty Feedback Value

A/C load feedback value

-

PS Duty Feedback Value

Power steering load feedback value

-

Idle Injection Volume (Min)

Idle minimum injection volume

-

Electric Fan Motor

Electric fan motors operation status

-

Immobiliser Fuel Cut History

Status of the immobiliser fuel cut history

-

Shift SW Status (N,P Range) Supported

Status of shift switch supported

-

Shift SW Status (N,P Range)

Shift switch status

-

MT Down Shift Indication

Manual transaxle down shift indicator status

-

MT Up Shift Indication

Manual transaxle up shift indicator status

-

Stop&Start of Eng State

Engine status of stop and start system

-