SFI SYSTEM Fuel Pump Control Circuit

DTC Code DTC Name
Fuel Pump Control Circuit

DESCRIPTION

The fuel pump circuit consists of the ECM, fuel pump (for low pressure side) and fuel pump control ECU assembly (which operates the fuel pump). Based on the engine output, the ECM determines the fuel pump speed. The speed is then converted to a duty signal and sent to the fuel pump control ECU assembly. Based on the signal sent from the ECM, the fuel pump control ECU adjust the fuel pump operation speed.

WIRING DIAGRAM

A349753E04

CAUTION / NOTICE / HINT

Note:

Inspect the fuses for circuits related to this system before performing the following procedure.

PROCEDURE

  1. PERFORM ACTIVE TEST USING GTS (ACTIVATE THE CIRCUIT RELAY)

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine / Active Test / Activate the Circuit Relay.

      Powertrain > Engine > Active Test

      Tester Display

      Activate the Circuit Relay

    5. Check whether operating sounds can be heard while operating the fuel pump (for low pressure side) using the GTS.

      OK

      Operating sounds can be heard from the fuel pump (for low pressure side).

    Result

    Proceed to

    OK

    NG

    NG

    CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL PUMP CONTROL ECU ASSEMBLY)Click here

    OK
  2. PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP DUTY RATIO, ACTIVATE THE CIRCUIT RELAY)

    A285444C10

    *a

    Component with harness connected

    (Fuel Pump [for Low Pressure Side])

    1. Remove the fuel pump (for low pressure side) from the fuel tank assembly.

      Click hereClick here

    2. Clean the fuel pump to completely remove any remaining fuel.

    3. Connect the fuel pump connector.

      CAUTION:

      Make sure that there is no fuel remaining inside or on the outside of the fuel pump.

    4. Connect the GTS to the DLC3.

    5. Turn the ignition switch to ON.

    6. Turn the GTS on.

    7. Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump Duty Ratio.

      Powertrain > Engine > Active Test

      Tester Display

      Control the Fuel Pump Duty Ratio

    8. Operate the fuel pump (for low pressure side) using the Active Test function and measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      GTS Operation

      Specified Condition

      2 - 1

      Fuel pump duty ratio: 25%

      3.2 to 4.05 V

      Fuel pump duty ratio: 80%

      8.8 to 12.5 V

    9. Enter the following menus: Powertrain / Engine / Active Test / Activate the Circuit Relay.

      Powertrain > Engine > Active Test

      Tester Display

      Activate the Circuit Relay

    10. Operate the fuel pump (for low pressure side) using the Active Test function and measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      GTS Operation

      Specified Condition

      2 - 1

      ON (Fuel pump duty ratio: 90%)

      9.0 to 14.0 V

      Tip:
      • Be sure to measure the voltage with all the connectors connected.

      • Before performing this inspection, check that the battery voltage is between 11 and 14 V (not depleted).

    Result

    Proceed to

    OK

    NG

    NG

    INSPECT FUEL PUMP (FOR LOW PRESSURE SIDE)Click here

    OK
  3. INSPECT FUEL PUMP (FOR LOW PRESSURE SIDE)

    1. Inspect the fuel pump (for low pressure side).

      Click here

    Result

    Proceed to

    OK

    NG

    OK

    END

    NG
  4. CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - ECM)

    1. Disconnect the fuel pump control ECU assembly connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      L21-2 (FPC) - A173-21 (FPC)

      Always

      Below 1 Ω

      L21-2 (FPC) or A173-21 (FPC) - Body ground and other terminals

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK
  5. REPLACE FUEL PUMP (FOR LOW PRESSURE SIDE)

    1. Replace the fuel pump (for low pressure side).

      Click hereClick here

      Tip:

      Perform "Inspection After Repair" after replacing the fuel pump (for low pressure side).

      Click hereClick here

    Result

    Proceed to

    NEXT

    NEXT
  6. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

    1. Check the fuel pump operation.

      Click hereClick here

      OK

      Malfunction has been repaired successfully.

    Result

    Proceed to

    OK

    NG

    OK

    END

    NG

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

  7. CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL PUMP CONTROL ECU ASSEMBLY)

    A256531C09

    *a

    Front view of wire harness connector

    (to Fuel Pump Control ECU Assembly)

    1. Disconnect the fuel pump control ECU assembly connector.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Condition

      Specified Condition

      L21-1 (+B) - L21-4 (E)

      Ignition switch ON

      11 to 14 V

    Result

    Proceed to

    OK

    NG

    NG

    CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - BODY GROUND)Click here

    OK
  8. INSPECT FUEL PUMP (FOR LOW PRESSURE SIDE)

    1. Inspect the fuel pump (for low pressure side).

      Click here

      Tip:

      Perform "Inspection After Repair" after replacing the fuel pump (for low pressure side).

      Click hereClick here

    Result

    Proceed to

    OK

    NG

    NG

    REPLACE FUEL PUMP (FOR LOW PRESSURE SIDE)

    OK
  9. CHECK HARNESS AND CONNECTOR (FUEL PUMP (FOR LOW PRESSURE SIDE) - FUEL PUMP CONTROL ECU ASSEMBLY)

    1. Disconnect the fuel pump (for low pressure side) connector.

    2. Disconnect the fuel pump control ECU assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      L20-4 (B) - L21-6 (FP)

      Always

      Below 1 Ω

      L20-5 (E) - L21-5 (FP-)

      Always

      Below 1 Ω

      L20-4 (B) or L21-6 (FP) - Body ground and other terminals

      Always

      10 kΩ or higher

      L20-5 (E) or L21-5 (FP-) - Body ground and other terminals

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK
  10. CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - ECM)

    1. Disconnect the fuel pump control ECU assembly connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      L21-2 (FPC) - A173-21 (FPC)

      Always

      Below 1 Ω

      L21-2 (FPC) or A173-21 (FPC) - Body ground and other terminals

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK
  11. REPLACE FUEL PUMP CONTROL ECU ASSEMBLY

    1. Replace the fuel pump control ECU assembly.

      for Hatchback:Click here

      for Wagon:Click here

    Result

    Proceed to

    NEXT

    NEXT
  12. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

    1. Check the fuel pump operation.

      Click hereClick here

      OK

      Malfunction has been repaired successfully.

    Result

    Proceed to

    OK

    NG

    OK

    END

    NG

    REPLACE ECM

  13. CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - BODY GROUND)

    1. Disconnect the fuel pump control ECU assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      L21-4 (E) - Body ground

      Always

      Below 1 Ω

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK
  14. CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - ECM)

    1. Disconnect the fuel pump control ECU assembly connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      L21-2 (FPC) - A173-21 (FPC)

      Always

      Below 1 Ω

      L21-2 (FPC) or A173-21 (FPC) - Body ground and other terminals

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK
  15. INSPECT EFI MAIN NO. 2 RELAY

    1. Inspect the EFI MAIN NO. 2 relay.

      Click here

    Result

    Proceed to

    OK

    NG

    NG

    REPLACE EFI MAIN NO. 2 RELAY

    OK
  16. CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY VOLTAGE)

    1. Remove the EFI MAIN NO. 2 relay from the engine room relay block and junction block assembly.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Condition

      Specified Condition

      5 (EFI-MAIN NO. 2 relay) - Body ground

      Always

      11 to 14 V

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - EFI-MAIN NO. 2 RELAY)

    OK
  17. CHECK HARNESS AND CONNECTOR (EFI MAIN NO. 2 RELAY - FUEL PUMP CONTROL ECU ASSEMBLY)

    1. Remove the EFI MAIN NO. 2 relay from the engine room relay block and junction block assembly.

    2. Disconnect the fuel pump control ECU assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      3 (EFI MAIN NO. 2 relay) - L21-1 (+B)

      Always

      Below 1 Ω

      3 (EFI MAIN NO. 2 relay) or L21-1 (+B) - Body ground and other terminals

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK
  18. CHECK HARNESS AND CONNECTOR (EFI-MAIN RELAY - EFI MAIN NO. 2 RELAY)

    1. Remove the EFI MAIN NO. 2 and EFI-MAIN relays from the engine room relay block and junction block assembly.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      3 (EFI-MAIN relay) - 1 (EFI MAIN NO. 2 relay)

      Always

      Below 1 Ω

      3 (EFI-MAIN relay) or 1 (EFI MAIN NO. 2 relay) - Body ground and other terminals

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK
  19. CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - BODY GROUND)

    1. Remove the EFI MAIN NO. 2 relay from the engine room relay block and junction block assembly.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      2 (EFI MAIN NO. 2 relay) - Body ground

      Always

      Below 1 Ω

    Result

    Proceed to

    OK

    NG

    OK

    CHECK ECM POWER SOURCE CIRCUIT

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR