CHARGING SYSTEM, Diagnostic DTC:P161A87

DTC Code DTC Name
P161A87 Lost Communication with Alternator Missing Message

DESCRIPTION

The ECM communicates with the generator assembly via LIN communication. If a LIN communication error is detected, the ECM stores this DTC.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Warning Indicate

Memory

Note

P161A87

Lost Communication with Alternator Missing Message

Generator assembly or ECM communication stops for approximately 17 minutes or more with the ignition switch ON

(1 trip detection logic)

  • Wire harness or connector

  • generator assembly

  • ECM

Charge warning light does not come on

DTC stored

SAE Code: P161A

WIRING DIAGRAM

Figure 1. w/ Stop and Start System
A331106E29
Figure 2. w/o Stop and Start System
A348065E08

CAUTION / NOTICE / HINT

Note:
  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

  • Before replacing the ECM, refer to Service Bulletin.

PROCEDURE

  1. CHECK CHARGING SYSTEM

    1. Check the charging system.

      Click here

    Result

    Result

    Proceed to

    OK (w/ Stop and Start System)

    A

    OK (w/o Stop and Start System)

    B

    NG

    C

    B

    CHECK HARNESS AND CONNECTOR (ECM - GENERATOR ASSEMBLY)Click here

    C

    REPAIR OR REPLACE CHARGING SYSTEM

    A
  2. CHECK HARNESS AND CONNECTOR (ECM - GENERATOR ASSEMBLY)

    1. Disconnect the B208 ECM connector.

    2. Disconnect the B184 generator assembly connector.

    3. Disconnect the A172 battery state sensor assembly connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)

      Tester Connection

      Condition

      Specified Condition

      A172-2 (LIN) or B184-2 (LIN) - B208-61 (LIN)

      Always

      Below 1 Ω

      Standard Resistance (Check for Short)

      Tester Connection

      Condition

      Specified Condition

      A172-2(LIN), B184-2 (LIN) or B208-61 (LIN) - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK
  3. CLEAR DTCS

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine / Trouble Codes.

    5. Check for DTCs, and then write them down.

      Powertrain > Engine > Trouble Codes

    6. Enter the following menus: Powertrain / Engine / Trouble Codes.

    7. Clear the DTCs.

      Powertrain > Engine > Clear DTCs

    8. Turn the ignition switch off and wait 30 seconds.

    Result

    Proceed to

    NEXT

    NEXT
  4. CHECK FOR DTCS

    1. Connect the GTS to the DLC3.

    2. Start the engine.

    3. Allow the engine to idle for approximately 17 minutes or more.

    4. Turn the GTS on.

    5. Enter the following menus: Powertrain / Engine / Trouble Codes.

    6. Check for DTCs.

      Powertrain > Engine > Trouble Codes

    Result

    Result

    Proceed to

    Only DTC P161A87 is output.

    A

    DTC P161A87 and P162B87 are output.

    B

    DTCs are not output.

    C

    A

    REPLACE GENERATOR ASSEMBLY

    B

    REPLACE ECM

    C

    CHECK FOR INTERMITTENT PROBLEMS

  5. CHECK HARNESS AND CONNECTOR (ECM - GENERATOR ASSEMBLY)

    1. Disconnect the B208 ECM connector.

    2. Disconnect the B184 generator assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)

      Tester Connection

      Condition

      Specified Condition

      B184-2 (LIN) - B208-61 (LIN)

      Always

      Below 1 Ω

      Standard Resistance (Check for Short)

      Tester Connection

      Condition

      Specified Condition

      B184-2 (LIN) or B208-61 (LIN) - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG

    OK

    REPLACE GENERATOR ASSEMBLY

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR