SFI SYSTEM Starter Signal Circuit

DTC Code DTC Name
Starter Signal Circuit

DESCRIPTION

  • w/ Entry and Start System:

    • When the engine is being cranked by engine switch operation:

      Current flows from terminal STAR of the certification ECU (smart key ECU assembly) to the park/neutral position switch assembly or clutch start switch assembly and then to terminal STA of the ECM (STA signal). The ECM then performs control to start the engine.

    • When the engine is being cranked by stop and start control:

      Current flows from terminal STA of the engine stop and start ECU to terminal STA of the ECM (STA signal). The ECM then performs control to start the engine.

  • w/o Entry and Start System:

    • When the engine is being cranked by ignition or starter switch assembly operation:

      Current flows from terminal ST2 of the ignition or starter switch assembly to the park/neutral position switch assembly or clutch start switch assembly and then terminal STA of the ECM (STA signal). The ECM then performs control to start the engine.

    • When the engine is being cranked by stop and start control:

      Current flows from terminal STA of the engine stop and start ECU to terminal STA of the ECM (STA signal). The ECM then performs control to start the engine.

WIRING DIAGRAM

Refer to DTC P061512.

Click here

CAUTION / NOTICE / HINT

Note:
  • Inspect the fuses for circuits related to this system before performing the following procedure.

  • After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click hereClick here

  • When the starter assembly is replaced, the number of starter operations stored in the engine stop and start ECU must be reset (w/ Stop and Start System).

    Click here

PROCEDURE

  1. CHECK WHETHER ENGINE CAN BE CRANKED

    1. Check if the engine can be cranked.

    Result

    Result

    Proceed to

    Engine cannot be cranked

    A

    Engine can be cranked

    B

    B

    READ VALUE USING GTS (STARTER SW)Click here

    A
  2. READ VALUE USING GTS (STARTER SW)

    1. Connect the GTS to DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine / Data List / All Data / Starter SW.

      Powertrain > Engine > Data List

      Tester Display

      Starter SW

    5. Check the value displayed on the GTS when the ignition switch is turned to ON and the engine is started.

    OK

    Condition

    GTS Display (Starter SW)

    Ignition switch ON

    OFF

    Cranking position

    ON

    Result

    Result

    Proceed to

    OK

    A

    NG (for CVT models)

    B

    NG (for M/T models)

    C

    B

    INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLYClick here

    C

    INSPECT CLUTCH START SWITCH ASSEMBLYClick here

    A
  3. INSPECT RELAY (ST NO. 1 RELAY)

    1. Inspect the ST NO. 1 relay.

      Click here

    Result

    Proceed to

    OK

    NG

    NG

    REPLACE RELAY (ST NO. 1 RELAY)

    OK
  4. INSPECT STARTER ASSEMBLY

    1. Inspect the starter assembly.

      w/o Stop and Start System:Click here

      for CVT models with Stop and Start System:Click here

      for M/T models with Stop and Start System:Click here

    Result

    Proceed to

    OK

    NG

    NG

    REPLACE STARTER ASSEMBLY

    w/o Stop and Start System:Click hereClick here

    for CVT models with Stop and Start System:Click hereClick here

    for M/T models with Stop and Start System:Click hereClick here

    OK
  5. CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - ECM)

    1. Remove the ST NO. 1 relay from the engine room relay block and junction block assembly.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      2 (ST NO. 1 relay) - A173-29 (STA)

      Always

      Below 1 Ω

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK
  6. CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - STARTER ASSEMBLY)

    1. Remove the ST NO. 1 relay from the engine room relay block and junction block assembly.

    2. Disconnect the starter assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (w/ Stop and Start System)

      Tester Connection

      Condition

      Specified Condition

      3 (ST NO. 1 relay) - B209-2

      Always

      Below 1 Ω

      3 (ST NO. 1 relay) or B209-2 - Body ground and other terminals

      Always

      10 kΩ or higher

      Standard Resistance (w/o Stop and Start System)

      Tester Connection

      Condition

      Specified Condition

      3 (ST NO. 1 relay) - B8-1

      Always

      Below 1 Ω

      3 (ST NO. 1 relay) or B8-1 - Body ground and other terminals

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK
  7. CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)

    1. Remove the ST NO. 1 relay from the engine room relay block and junction block assembly.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      1 (ST NO. 1 relay) - Body ground

      Always

      Below 1 Ω

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK
  8. CHECK HARNESS AND CONNECTOR (BATTERY - ST NO. 1 RELAY)

    1. Remove the ST NO. 1 relay from the engine room relay block and junction block assembly.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Condition

      Specified Condition

      5 (ST NO. 1 relay) - Body ground

      Always

      11 to 14 V

    Result

    Proceed to

    OK

    NG

    OK

    REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - STARTER ASSEMBLY)

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  9. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

    1. Inspect the park/neutral position switch assembly.

      Click here

    Result

    Proceed to

    OK

    NG

    NG

    REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

    OK
  10. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY VOLTAGE)

    1. Disconnect the park/neutral position switch assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Condition

      Specified Condition

      B110-4 (B) - Body ground

      Engine cranking position

      11 to 14 V

    Result

    Result

    Proceed to

    OK (w/ Entry and Start System)

    A

    OK (w/o Entry and Start System)

    B

    NG (w/ Entry and Start System)

    C

    NG (w/o Entry and Start System)

    D

    B

    CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST NO. 1 RELAY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)Click here

    C

    CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - SMART KEY ECU ASSEMBLY - ECM - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)Click here

    D

    INSPECT IGNITION OR STARTER SWITCH ASSEMBLYClick here

    A
  11. CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - SMART KEY ECU ASSEMBLY - ST NO. 1 RELAY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)

    1. Disconnect the engine stop and start ECU connector.

    2. Disconnect the smart key ECU assembly connector.

    3. Disconnect the park/neutral position switch assembly connector.

    4. Remove the ST NO. 1 relay from the engine room relay block and junction block assembly.

    5. Disconnect the ECM connector.

    6. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      A9-21 (STA) - 2 (ST NO. 1 relay)

      Always

      Below 1 Ω

      E33-7 (STA) - B110-9 (L)

      Always

      Below 1 Ω

      2 (ST NO. 1 relay) - A173-29 (STA)

      Always

      Below 1 Ω

      A9-21 (STA), A173-29 (STA), E33-7 (STA), 2 (ST NO. 1 relay) or B110-9 (L) - Body ground and other terminals

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG

    OK

    CHECK ENTRY AND START SYSTEM (FOR START FUNCTION)

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  12. CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST NO. 1 RELAY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)

    1. Disconnect the engine stop and start ECU connector.

    2. Disconnect the park/neutral position switch assembly connector.

    3. Remove the ST NO. 1 relay from the engine room relay block and junction block assembly.

    4. Disconnect the ECM connector.

    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      A9-21 (STA) - 2 (ST NO. 1 relay)

      Always

      Below 1 Ω

      2 (ST NO. 1 relay) - B110-9 (L)

      Always

      Below 1 Ω

      2 (ST NO. 1 relay) - A173-29 (STA)

      Always

      Below 1 Ω

      A9-21 (STA), A173-29 (STA), 2 (ST NO. 1 relay) or B110-9 (L) - Body ground and other terminals

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG

    OK

    CHECK STOP AND START SYSTEM (STA SIGNAL)

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  13. CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - SMART KEY ECU ASSEMBLY - ECM - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

    1. Disconnect the engine stop and start ECU connector.

    2. Disconnect the smart key ECU assembly connector.

    3. Disconnect the park/neutral position switch assembly connector.

    4. Disconnect the ECM connector.

    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      A9-28 (CLL) - A173-57 (NSW)

      Always

      Below 1 Ω

      A9-28 (CLL) - B110-4 (B)

      Always

      Below 1 Ω

      E33-5 (STAR) - B110-4 (B)

      Always

      Below 1 Ω

      A9-28 (CLL), A173-57 (NSW), E33-5 (STAR) or B110-4 (B) - Body ground and other terminals

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG

    OK

    CHECK ENTRY AND START SYSTEM (FOR START FUNCTION)

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  14. INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

    1. Inspect the ignition or starter switch assembly.

      Click here

    Result

    Proceed to

    OK

    NG

    NG

    REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

    OK
  15. CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY VOLTAGE)

    1. Disconnect the ignition or starter switch assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Condition

      Specified Condition

      E4-4 (AM2) - Body ground

      Always

      11 to 14 V

    Result

    Proceed to

    OK

    NG

    OK

    REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ENGINE STOP AND START ECU - ECM)

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION OR STARTER SWITCH ASSEMBLY)

  16. INSPECT CLUTCH START SWITCH ASSEMBLY

    1. Inspect the clutch start switch assembly.

      Click here

    Result

    Proceed to

    OK

    NG

    NG

    REPLACE CLUTCH START SWITCH ASSEMBLY

    OK
  17. CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY VOLTAGE)

    1. Disconnect the clutch start switch assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Condition

      Specified Condition

      A5-2 - Body ground

      Engine cranking position

      11 to 14 V

    Result

    Result

    Proceed to

    OK (w/ Entry and Start System [w/ Stop and Start System])

    A

    OK (w/ Entry and Start System [w/o Stop and Start System])

    B

    OK (w/o Entry and Start System [w/ Stop and Start System])

    C

    OK (w/o Entry and Start System [w/o Stop and Start System])

    D

    NG (w/ Entry and Start System [w/ Stop and Start System])

    E

    NG (w/ Entry and Start System [w/o Stop and Start System])

    F

    NG (w/o Entry and Start System [w/ Stop and Start System])

    G

    NG (w/o Entry and Start System [w/o Stop and Start System])

    H

    B

    REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - SMART KEY ECU ASSEMBLY - CLUTCH START SWITCH ASSEMBLY - ST NO. 1 RELAY)

    C

    CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST NO. 1 RELAY - CLUTCH START SWITCH ASSEMBLY - ECM)Click here

    D

    REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - CLUTCH START SWITCH ASSEMBLY - ST NO. 1 RELAY)

    E

    CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - SMART KEY ECU ASSEMBLY - ECM - CLUTCH START SWITCH ASSEMBLY)Click here

    F

    CHECK HARNESS AND CONNECTOR (SMART KEY ECU ASSEMBLY - ECM - CLUTCH START SWITCH ASSEMBLY)Click here

    G

    INSPECT IGNITION OR STARTER SWITCH ASSEMBLYClick here

    H

    INSPECT IGNITION OR STARTER SWITCH ASSEMBLYClick here

    A
  18. CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - SMART KEY ECU ASSEMBLY - ST NO. 1 RELAY - CLUTCH START SWITCH ASSEMBLY - ECM)

    1. Disconnect the engine stop and start ECU connector.

    2. Disconnect the smart key ECU assembly connector.

    3. Disconnect the clutch start switch assembly connector.

    4. Remove the ST NO. 1 relay from the engine room relay block and junction block assembly.

    5. Disconnect the ECM connector.

    6. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      A9-21 (STA) - 2 (ST NO. 1 relay)

      Always

      Below 1 Ω

      E33-7 (STA) - A5-1

      Always

      Below 1 Ω

      2 (ST NO. 1 relay) - A173-29 (STA)

      Always

      Below 1 Ω

      A9-21 (STA), A173-29 (STA), E33-7 (STA), 2 (ST NO. 1 relay) or A5-1 - Body ground and other terminals

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG

    OK

    CHECK ENTRY AND START SYSTEM (FOR START FUNCTION)

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  19. CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST NO. 1 RELAY - CLUTCH START SWITCH ASSEMBLY - ECM)

    1. Disconnect the engine stop and start ECU connector.

    2. Disconnect the clutch start switch assembly connector.

    3. Remove the ST NO. 1 relay from the engine room relay block and junction block assembly.

    4. Disconnect the ECM connector.

    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      A9-21 (STA) - 2 (ST NO. 1 relay)

      Always

      Below 1 Ω

      2 (ST NO. 1 relay) - A5-1

      Always

      Below 1 Ω

      2 (ST NO. 1 relay) - A173-29 (STA)

      Always

      Below 1 Ω

      A9-21 (STA), A173-29 (STA), 2 (ST NO. 1 relay) or A5-1 - Body ground and other terminals

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG

    OK

    CHECK STOP AND START SYSTEM (STA SIGNAL)

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  20. CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - SMART KEY ECU ASSEMBLY - ECM - CLUTCH START SWITCH ASSEMBLY)

    1. Disconnect the engine stop and start ECU connector.

    2. Disconnect the smart key ECU assembly connector.

    3. Disconnect the clutch start switch assembly connector.

    4. Disconnect the ECM connector.

    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      A9-28 (CLL) - A5-2

      Always

      Below 1 Ω

      A9-28 (CLL) - A173-57 (NSW)

      Always

      Below 1 Ω

      E33-5 (STAR) - A173-57 (NSW)

      Always

      Below 1 Ω

      A9-28 (CLL), A5-2, E33-5 (STAR) or A173-57 (NSW) - Body ground and other terminals

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG

    OK

    CHECK ENTRY AND START SYSTEM (FOR START FUNCTION)

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  21. CHECK HARNESS AND CONNECTOR (SMART KEY ECU ASSEMBLY - ECM - CLUTCH START SWITCH ASSEMBLY)

    1. Disconnect the smart key ECU assembly connector.

    2. Disconnect the clutch start switch assembly connector.

    3. Disconnect the ECM connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      A173-57 (NSW) - A5-2

      Always

      Below 1 Ω

      E33-5 (STAR) - A5-2

      Always

      Below 1 Ω

      A173-57 (NSW), E33-5 (STAR) or A5-2 - Body ground and other terminals

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG

    OK

    CHECK ENTRY AND START SYSTEM (FOR START FUNCTION)

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  22. INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

    1. Inspect the ignition or starter switch assembly.

      Click here

    Result

    Proceed to

    OK

    NG

    NG

    REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

    OK
  23. CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY VOLTAGE)

    1. Disconnect the ignition or starter switch assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Condition

      Specified Condition

      E4-4 (AM2) - Body ground

      Always

      11 to 14 V

    Result

    Proceed to

    OK

    NG

    OK

    REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY - ENGINE STOP AND START ECU - ECM)

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  24. INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

    1. Inspect the ignition or starter switch assembly.

      Click here

    Result

    Proceed to

    OK

    NG

    NG

    REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

    OK
  25. CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY VOLTAGE)

    1. Disconnect the ignition or starter switch assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Condition

      Specified Condition

      E4-4 (AM2) - Body ground

      Always

      11 to 14 V

    Result

    Proceed to

    OK

    NG

    OK

    REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY - ECM)

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  26. READ VALUE USING GTS (STARTER SW)

    1. Connect the GTS to DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine / Data List / All Data / Starter SW.

      Powertrain > Engine > Data List

      Tester Display

      Starter SW

    5. Check the value displayed on the GTS when the ignition switch is turned to ON and the engine is started.

    OK

    Condition

    GTS Display (Starter SW)

    Ignition switch ON

    OFF

    Cranking position

    ON

    Result

    Proceed to

    OK

    NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (ST NO. 1 RELAY - ECM)