CURTAIN SHIELD AIRBAG ASSEMBLY INSTALLATION
CAUTION / NOTICE / HINT
Use the same procedure for the RH side and LH side.
The procedure listed below is for the LH side.
PROCEDURE
INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY (for Hatchback)
Note:When installing a curtain shield airbag assembly, have assistants hold it to prevent it from bending.
Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
CAUTION:Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Engage the 2 hooks in the order shown in the illustration to temporarily install the curtain shield airbag assembly.
Note:Do not twist the curtain shield airbag assembly when installing it.
Install 2 new bolts, 6 new clips with pins and 2 new spacers, and engage the 4 clips in the order shown in the illustration to install the curtain shield airbag assembly to the body panel.
9.8 N*m
100 kgf*cm
87 in.*lbf
Tip:Engage the 2 claws to install the new clip.
*1
Pin
*2
Curtain Shield Airbag Assembly
*3
Spacer
-
-
*a
Clip
*b
Body Panel
*c
Spacer Location
-
-
Push the 6 pins into the 6 clips.
Note:Make sure that the pins of the clips are pushed in firmly.
-
*a
Airbag Connector
*b
Airbag Connector Lock
Connect the airbag connector.
Note:When connecting any airbag connector, take care not to damage the airbag wire harness.
Push in the airbag connector lock to install the airbag connector.
INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY (for Wagon)
Note:When installing a curtain shield airbag assembly, have assistants hold it to prevent it from bending.
Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
CAUTION:Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Engage the 2 hooks in the order shown in the illustration to temporarily install the curtain shield airbag assembly.
Note:Do not twist the curtain shield airbag assembly when installing it.
Install 2 new bolts, 6 new clips with pins and 2 new spacers, and engage the 4 clips in the order shown in the illustration to install the curtain shield airbag assembly to the body panel.
9.8 N*m
100 kgf*cm
87 in.*lbf
Tip:Engage the 2 claws to install the new clip.
*1
Pin
*2
Curtain Shield Airbag Assembly
*3
Spacer
-
-
*a
Clip
*b
Body Panel
*c
Spacer Location
-
-
Push the 6 pins into the 6 clips.
Note:Make sure that the pins of the clips are pushed in firmly.
-
*a
Airbag Connector
*b
Airbag Connector Lock
Connect the airbag connector.
Note:When connecting any airbag connector, take care not to damage the airbag wire harness.
Push in the airbag connector lock to install the airbag connector.
INSTALL NO. 2 SIDE PANEL STRENGTH BRACKET (for Wagon)
Engage the hook and install the No. 2 side panel strength bracket with the bolt.
INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY (for Sedan)
Note:When installing a curtain shield airbag assembly, have assistants hold it to prevent it from bending.
Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
CAUTION:Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Install 2 new bolts, 6 new clips with pins and 2 new spacers, and engage the 2 hooks and 4 clips in the order shown in the illustration to install the curtain shield airbag assembly to the body panel.
11 N*m
112 kgf*cm
8 ft.*lbf
Note:Do not twist the curtain shield airbag assembly when installing it.
Tip:Engage the 2 claws to install the new clip.
*1
Pin
*2
Spacer
*a
Clip
*b
Spacer Location
Push the 6 pins into the 6 clips.
Note:Make sure that the pins of the clips are pushed in firmly.
-
*a
Airbag Connector
*b
Airbag Connector Lock
Connect the airbag connector.
Note:When connecting any airbag connector, take care not to damage the airbag wire harness.
Push in the airbag connector lock to install the airbag connector.
INSTALL ROOF HEADLINING ASSEMBLY
for Hatchback:Click hereClick here
for Wagon:Click hereClick here
for Sedan:Click hereClick hereClick here
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
Note:When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
PERFORM DIAGNOSTIC SYSTEM CHECK
INSPECT SRS WARNING LIGHT