METER / GAUGE SYSTEM, Diagnostic DTC:B150A

DTC Code DTC Name
B150A Lost Communication with HMI-LAN

DESCRIPTION

The combination meter assembly receives a text data signal from the radio and display receiver assembly via local bus communication.

Based on this signal, audio and visual system or navigation system information is displayed on the multi-information display.

This DTC is stored when the combination meter assembly cannot receive the signal.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Memory

Note

B150A

Lost Communication with HMI-LAN

After the combination meter assembly receives a registration information signal, which is sent by the radio and display receiver assembly when the ignition switch is ACC, 1 or more times, the combination meter assembly cannot receive the signal for 30 seconds or more.

  • Harness or connector

  • Radio and display receiver assembly

  • Combination meter assembly

DTC stored

for Multi-information Display (Color Type) with Radio and Display Receiver Assembly

WIRING DIAGRAM

  1. E274272E51

PROCEDURE

  1. CONFIRM VEHICLE TYPE

    1. Choose the model to be inspected.

    Result

    Result

    Proceed to

    w/ Navigation System

    A

    w/o Navigation System

    B

    B

    CHECK FOR DTCClick here

    A
  2. CHECK FOR DTC

    1. Check if navigation system DTCs are output.

      Click hereClick here

      Body Electrical > Navigation System > Trouble Codes

    Result

    Result

    Proceed to

    Navigation system DTCs are not output.

    A

    Navigation system DTCs are output.

    B

    B

    GO TO NAVIGATION SYSTEM

    A
  3. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)

    1. Disconnect the E46 combination meter assembly connector.

    2. Disconnect the E125 radio and display receiver assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      E46-37 (MSCL) - E125-4 (CNL1)

      Always

      Below 1 Ω

      E46-36 (MSCH) - E125-3 (CNH1)

      Always

      Below 1 Ω

      E46-37 (MSCL) - Body ground

      Always

      10 kΩ or higher

      E46-36 (MSCH) - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK
  4. REPLACE COMBINATION METER ASSEMBLY

    1. Replace the combination meter assembly with a new or known good one.

      Click here

    2. Turn the ignition switch to ON and wait 30 seconds.

      Note:

      A maximum of 30 seconds is required to send/receive the registration information between the combination meter assembly and radio and display receiver assembly.

    3. Operate the steering pad switch assembly and check that the audio tab illuminates.

    4. Check for DTCs.

      Click here

      Body Electrical > Combination Meter > Trouble Codes

    Result

    Result

    Proceed to

    The audio tab illuminates and DTC B150A is not output.

    A

    The audio tab does not illuminate and DTC B150A is output.

    B

    A

    END

    B

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

  5. CHECK FOR DTC

    1. Check if audio and visual system DTCs are output.

      Click here

      Body Electrical > Navigation System > Trouble Codes

    Result

    Result

    Proceed to

    Audio and visual system DTCs are not output.

    A

    Audio and visual system DTCs are output.

    B

    A

    CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)Click here

    B

    GO TO AUDIO AND VISUAL SYSTEM