AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM(for Sedan) DATA LIST / ACTIVE TEST

  1. DATA LIST

    Note:

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    Tip:

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuator and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / HL AutoLeveling / Data List.

    5. Read the Data List according to the display on the GTS.

      Body Electrical > HL AutoLeveling > Data List

      Tester Display

      Measurement Item

      Range

      Normal Condition

      Diagnostic Note

      Headlight Low Beam State

      Low beam headlight state

      ON or OFF

      ON: Low beam headlights on

      OFF: Low beam headlights off

      -

      Headlight High Beam State

      High beam headlight state

      ON or OFF

      ON: High beam headlights on

      OFF: High beam headlights off

      -

      +B

      IG power supply voltage

      0.00 to 19.75 V

      11.00 to 14.00 V

      -

      Height Sens Pw Supply Val

      Rear height control sensor sub-assembly power supply voltage

      0.00 to 5.00 V

      Approx. 5.00 V

      -

      Rr Height Sens Signal Val

      Rear height control sensor sub-assembly signal

      0.00 to 5.00 V

      Approx. 2.50 V (When vehicle is level)

      Value changes according to vehicle height

      Front Right Wheel Speed Value

      Front right wheel speed

      0.00 to 260.00 km/h (162.00 mph)

      Vehicle stopped: 0 km/h (0 mph)

      -

      Front Left Wheel Speed Value

      Front left wheel speed

      0.00 to 260.00 km/h (162.00 mph)

      Vehicle stopped: 0 km/h (0 mph)

      -

      Vehicle Speed

      Vehicle speed

      0.00 to 260.00 km/h (162.00 mph)

      Vehicle stopped: 0 km/h (0 mph)

      -

      Rear Height Adjust Value

      Rear height adjustment off set value

      0 to 1023

      Actual normal rear height adjustment value is displayed (If there is a malfunction, no value is displayed)

      -

      Rear Height Adjust Valid Flag

      Rear height adjustment range

      Valid or Invalid

      Valid: Rear height control sensor sub-assembly value within normal range

      Invalid: Rear height control sensor sub-assembly value out of normal range

      -

      Init Writing Count

      Number of times for initialization

      0 to 255

      Number of times initialization performed

      -

      Sensor Initialization Hist

      Sensor initialization history

      not comp, 10%, 25%, 50%, 75%, 100% or complied

      Initialization status displayed

      -

      Number Of Trouble Codes

      Number of trouble codes

      0 to 255

      Number of stored DTCs displayed

      -

  2. ACTIVE TEST

    Tip:

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / HL AutoLeveling / Active Test.

    5. Perform the Active Test according to the display on the GTS.

      Body Electrical > HL AutoLeveling > Active Test

      Tester Display

      Measurement Item

      Control Range

      Diagnostic Note

      Drive The Leveling Motor

      Headlight leveling motor upward or downward operation

      Up/Down/Stop

      Perform the Active Test with the engine started and vehicle stopped

      Headlight Cleaner

      Function to operate the headlight cleaner motor

      OFF/ON

      -