STOP AND START SYSTEM Stop and Start Priority Control System
| DTC Code | DTC Name |
|---|---|
| Stop and Start Priority Control System |
DESCRIPTION
except Multi-information Display (Color Type)
The stop and stop control mode can be changed by pressing and holding the eco run cancel switch assembly.
When start priority control (LONG) mode is selected, "LONG" will be displayed on the multi-information display as an interruption message.
When the eco run cancel switch assembly is pressed and held to change the stop and start control mode, a signal is sent from the eco run cancel switch assembly to the engine stop and start ECU. Cooperative control is performed by the air conditioning amplifier assembly and engine stop and start ECU based on the selected control mode.
When stop and start priority control (LONG) is selected, the operation time of stop and start control will be extended in order to improve fuel economy.
for Multi-information Display (Color Type)
When the steering pad switch assembly is used to select a control mode, a status change request signal is sent from the combination meter assembly to the engine stop and start ECU via CAN communication. Cooperative control is performed by the air conditioning amplifier assembly and engine stop and start ECU based on the selected control mode.
When stop and start priority control (LONG) is selected, the operation time of stop and start control will be extended in order to improve fuel economy.
WIRING DIAGRAM
except Multi-information Display (Color Type)
for Multi-information Display (Color Type)
CAUTION / NOTICE / HINT
Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU
After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.
After replacing the engine stop and start ECU or airbag ECU assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.
When stop and start priority control (LONG) is selected, the operation of the air conditioning system is limited. If the customer reports that the cooling effectiveness of the air conditioning system is poor, check the selected control mode. If stop and start priority control (LONG) is selected, cancel the control mode and check if the cooling effectiveness of the air conditioning system improves. If it improves, explain to the customer that the operation of the air conditioning system was limited by stop and start control.
Depending on the vehicle conditions, the stop and start operation time may not change even if stop and start priority control (LONG) is selected.
PROCEDURE
CONFIRM MODEL
Choose the model to be inspected.
Result
Result
Proceed to
except Multi-information Display (Color Type)
A
for Multi-information Display (Color Type)
B
B CHECK PROBLEM SYMPTOMSClick here
CHECK PROBLEM SYMPTOMS
Check the problem symptoms.
Tip:Check each symptom by checking the suspected areas in the table below.
By using the GTS and entering the following menus, the selected mode can be confirmed.
Powertrain / Stop and Start / Data List / Stop & Start A/C Mode
Result
Problem Symptoms
Trouble Area
Proceed to
The control mode does not change and an interruption message is not displayed on the multi-information display
Eco run cancel switch assembly
Wire harness or connector
Air conditioning amplifier assembly
A
The control mode changes but an interruption message is not displayed on the multi-information display
Combination meter assembly
CAN communication system
B
The control mode does not change but an interruption message is displayed on the multi-information display
Air conditioning amplifier assembly
CAN communication system
C
Control mode returns to default mode after turning ignition switch to ON
Engine stop and start ECU
D
READ VALUE USING GTS (CANCEL SWITCH)
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Stop and Start / Data List / Cancel Switch.
Powertrain > Stop and Start > Data List
Tester Display
Cancel Switch
Powertrain > Stop and Start > Data List
Tester Display
Measurement Item
Range
Normal Condition
Diagnostic Note
Cancel Switch
Eco run cancel switch assembly signal
ON/OFF
ON: Eco run cancel switch assembly pressed
OFF: Eco run cancel switch assembly not pressed
-
Result
Result
Proceed to
GTS display changes when the cancel button is pressed
A
GTS display does not change even when the cancel button is pressed
B
B GO TO STOP AND START CANCEL SWITCH CIRCUIT
CHECK DTC OUTPUT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Perform a road test.
Enter the following menus: Powertrain / Stop and Start / Trouble Codes.
Powertrain > Stop and Start > Trouble Codes
Read the DTCs.
Result
Result
Proceed to
DTCs are not output
A
CAN DTCs are output
B
B GO TO CAN COMMUNICATION SYSTEM
w/o Central Gateway ECU:Click here
w/ Central Gateway ECU:Click here
CHECK DTC OUTPUT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Perform a road test.
Enter the following menus: Powertrain / Stop and Start / Trouble Codes.
Powertrain > Stop and Start > Trouble Codes
Read the DTCs.
Result
Result
Proceed to
DTCs are not output
A
CAN DTCs are output
B
B GO TO CAN COMMUNICATION SYSTEM
w/o Central Gateway ECU:Click here
w/ Central Gateway ECU:Click here
CHECK DTC OUTPUT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Perform a road test.
Enter the following menus: Powertrain / Stop and Start / Trouble Codes.
Powertrain > Stop and Start > Trouble Codes
Read the DTCs.
Result
Result
Proceed to
DTCs are not output
A
CAN DTCs are output
B
B GO TO CAN COMMUNICATION SYSTEM
w/o Central Gateway ECU:Click here
w/ Central Gateway ECU:Click here
CHECK PROBLEM SYMPTOMS
Check the problem symptoms.
Tip:Check each symptom by checking the suspected areas in the table below.
By using the GTS and entering the following menus, the selected mode can be confirmed.
Powertrain / Stop and Start / Data List / Stop & Start A/C Mode
Result
Problem Symptoms
Trouble Area
Proceed to
Multi-information display screen does not change after pressing steering pad switch assembly
Steering pad switch assembly
Spiral cable with sensor sub-assembly
Combination meter assembly
Engine stop and start ECU
Wire harness or connector (steering pad switch assembly - combination meter assembly)
Wire harness or connector (engine stop and start ECU - combination meter assembly)
A
Multi-information display screen changes without pressing steering pad switch assembly
Steering pad switch assembly
Spiral cable with sensor sub-assembly
Wire harness or connector (steering pad switch assembly - combination meter assembly)
B
Multi-information display screen does not change but control mode changes
Combination meter assembly
C
Multi-information display screen changes but control mode does not change
Air conditioning amplifier assembly
Wire harness or connector (engine stop and start ECU - air conditioning amplifier assembly)
D
Control mode returns to default mode after turning ignition switch to ON
Engine stop and start ECU
E
B CHECK HARNESS AND CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - COMBINATION METER ASSEMBLY)Click here
D CHECK DTC OUTPUTClick here
E CHECK DTC OUTPUTClick here
CHECK OPERATION
Using the steering pad switch assembly, check that all functions other than "Stop and Start A/c Mode" can be selected.
Result
Result
Proceed to
Only "Stop and Start A/C Mode" cannot be selected
A
No function can be selected using the steering pad switch assembly
B
B CHECK HARNESS AND CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - COMBINATION METER ASSEMBLY)Click here
CHECK DTC OUTPUT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Perform a road test.
Enter the following menus: Powertrain / Stop and Start / Trouble Codes.
Powertrain > Stop and Start > Trouble Codes
Read the DTCs.
Result
Result
Proceed to
DTCs are not output
A
CAN DTCs are output
B
B GO TO CAN COMMUNICATION SYSTEM
w/o Central Gateway ECU:Click here
w/ Central Gateway ECU:Click here
CHECK HARNESS AND CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - COMBINATION METER ASSEMBLY)
Turn the ignition switch off.
Disconnect the E6 spiral cable with sensor sub-assembly connector.
Disconnect the E46 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection
Condition
Specified Condition
E6-10 (+DP) - E46-28 (SW1)
Always
Below 1 Ω
E6-10 (+DP) - Body ground
Always
10 kΩ or higher
E46-28 (SW1) - Body ground
Always
10 kΩ or higher
E6-11 (+DP2) - E46-33 (MSSL)
Always
Below 1 Ω
E6-11 (+DP2) - Body ground
Always
10 kΩ or higher
E46-33 (MSSL) - Body ground
Always
10 kΩ or higher
E6-3 (EAU) - Body ground
Always
Below 1 Ω
Result
Proceed to
OK
NG
NG REPAIR OR REPLACE HARNESS OR CONNECTOR
INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
Inspect the spiral cable with sensor sub-assembly.
Result
Proceed to
OK
NG
INSPECT STEERING PAD SWITCH ASSEMBLY
Inspect the steering pad switch assembly.
Result
Proceed to
OK
NG
CHECK HARNESS AND CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - COMBINATION METER ASSEMBLY)
Turn the ignition switch off.
Disconnect the E6 spiral cable with sensor sub-assembly connector.
Disconnect the E46 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection
Condition
Specified Condition
E6-10 (+DP) - E46-28 (SW1)
Always
Below 1 Ω
E6-10 (+DP) - Body ground
Always
10 kΩ or higher
E46-28 (SW1) - Body ground
Always
10 kΩ or higher
E6-11 (+DP2) - E46-33 (MSSL)
Always
Below 1 Ω
E6-11 (+DP2) - Body ground
Always
10 kΩ or higher
E46-33 (MSSL) - Body ground
Always
10 kΩ or higher
E6-3 (EAU) - Body ground
Always
Below 1 Ω
Result
Proceed to
OK
NG
NG REPAIR OR REPLACE HARNESS OR CONNECTOR
INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
Inspect the spiral cable with sensor sub-assembly.
Result
Proceed to
OK
NG
INSPECT STEERING PAD SWITCH ASSEMBLY
Inspect the steering pad switch assembly.
Result
Proceed to
OK
NG
CHECK DTC OUTPUT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Perform a road test.
Enter the following menus: Powertrain / Stop and Start / Trouble Codes.
Powertrain > Stop and Start > Trouble Codes
Read the DTCs.
Result
Result
Proceed to
DTCs are not output
A
CAN DTCs are output
B
B GO TO CAN COMMUNICATION SYSTEM
w/o Central Gateway ECU:Click here
w/ Central Gateway ECU:Click here
CHECK DTC OUTPUT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Perform a road test.
Enter the following menus: Powertrain / Stop and Start / Trouble Codes.
Powertrain > Stop and Start > Trouble Codes
Read the DTCs.
Result
Result
Proceed to
DTCs are not output
A
DTCs are output
B