AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM(for Sedan) TERMINALS OF ECU

  1. E101528N47

    CHECK HEADLIGHT LEVELING ECU ASSEMBLY

    1. Disconnect the A182 headlight leveling ECU assembly connector.

    2. Measure the voltage and resistance according to the value(s) in the table below.

      Terminal No. (Symbol)

      Wiring Color

      Terminal Description

      Condition

      Specified Condition

      A182-1 (IG) - Body ground

      L - Body ground

      IG power supply

      Ignition switch off

      Below 1 V

      Ignition switch on (IG)

      11 to 14 V

      A182-9 (E1) - Body ground

      W-B - Body ground

      Ground

      Always

      Below 1 Ω

      If the result is not as specified, there may be a malfunction on the wire harness side.

    3. Reconnect the A182 headlight leveling ECU assembly connector.

    4. Measure the resistance and voltage and check for pulses according to the value(s) in the table below.

      Terminal No. (Symbol)

      Wiring Color

      Terminal Description

      Condition

      Specified Condition

      A182-6 (CANH) - Body ground

      Y - Body ground

      CAN communication line

      Ignition switch off

      Below 1 V

      Ignition switch on (IG)

      Pulse generation

      A182-7 (CANL) - Body ground

      W - Body ground

      CAN communication line

      Ignition switch off

      Below 1 V

      Ignition switch on (IG)

      Pulse generation

      A182-10 (RH+) - Body ground

      Y - Body ground

      Headlight leveling motor RH power supply

      Ignition switch off

      Below 1 V

      Ignition switch on (IG)

      11 to 14 V

      A182-11 (LH+) - Body ground

      W - Body ground

      Headlight leveling motor LH power supply

      Ignition switch off

      Below 1 V

      Ignition switch on (IG)

      11 to 14 V

      A182-12 (SBR) - Body ground

      SB - Body ground

      Rear height control sensor sub-assembly power supply

      Ignition switch off

      Below 1 V

      Ignition switch on (IG)

      4.75 to 5.25 V

      A182-17 (RHT) - Body ground

      W - Body ground

      Headlight leveling motor RH operation signal input

      With low beam headlights on, vehicle height not changed

      Below 1 V

      With low beam headlights on, vehicle height changed and maintained for more than 3 seconds

      1.0 to 14.4 V

      A182-18 (LHT) - Body ground

      LG - Body ground

      Headlight leveling motor LH operation signal input

      With low beam headlights on, vehicle height not changed

      Below 1 V

      With low beam headlights on, vehicle height changed and maintained for more than 3 seconds

      1.0 to 14.4 V

      A182-19 (SHRL) - Body ground

      GR - Body ground

      Rear height control sensor sub-assembly signal input

      Ignition switch off

      Below 1 V

      Ignition switch on (IG)

      0.5 to 4.5 V

      A182-21 (SGR) - Body ground

      L - Body ground

      Rear height control sensor sub-assembly ground

      Always

      Below 1 Ω

      A182-23 (RH-) - Body ground

      B - Body ground

      Headlight leveling motor RH ground

      Always

      Below 1 Ω

      A182-24 (LH-) - Body ground

      SB - Body ground

      Headlight leveling motor LH ground

      Always

      Below 1 Ω

      If the result is not as specified, the headlight leveling ECU assembly may be malfunctioning.