CHARGING SYSTEM DATA LIST / ACTIVE TEST

  1. DATA LIST

    Tip:

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note:

    In the table below, the values listed under Normal Condition are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    1. Warm up the engine.

    2. Turn the ignition switch off.

    3. Connect the GTS to the DLC3.

    4. Turn the ignition switch to ON.

    5. Turn the GTS on.

    6. Enter the following menus: Powertrain / Engine / Data List.

    7. According to the display on the GTS, read the Data List.

      Powertrain > Engine > Data List

      Tester Display

      Measurement Item

      Range

      Normal Condition

      Diagnostic Note

      Battery Voltage

      Battery voltage

      Min.: 0.0 V

      Max.: 65.5 V

      11 to 14 V (Idling)

      If the result is not as specified, abnormal battery voltage is suspected.

      Battery Sensor Voltage

      Battery sensor voltage

      Min.: 0.000 V

      Max.: 79.998 V

      11 to 14 V (Idling)

      w/ Stop and Start System

      Battery Current

      Battery current

      Min.: -125.0 A

      Max.: 124.9 A

      Changes according to alternator output

      (While driving after engine warmed up)

      • If the result is not as specified, a malfunction of LIN communication is suspected.

      • w/ Stop and Start System

      Battery Temperature

      Battery temperature

      Min.: -40.0°C (-40°F)

      Max.: 6513.5 °C (11756 °F)

      Changes according to actual temperature

      (While driving after engine warmed up)

      • If the result is not as specified, a malfunction of LIN communication is suspected.

      • w/ Stop and Start System

      Alternator Output Duty Ratio

      Generator output duty

      Min.: 0.0%

      Max.: 399.9%

      Changes in accordance with the generator output

      If the result is not as specified, a malfunction of the charging control system is suspected.

      Alternator Voltage - Non Active Test

      Requested voltage when regulator forced drive is not executed

      Min.: 0.000 V

      Max.: 79.998 V

      12.2 to 15.3 V

      (After engine start (Varies with regulator temperature or driving conditions))

      Active Test support data

      Voltage of Alternator

      Requested voltage when regulator forced drive is executed

      Min.: 0.0 V

      Max.: 79.9 V

      Required instruction voltage value when the Active Test "Control the Voltage of Alternator" is executed (12.5 to 14.8 V): After engine started

      Malfunction of the charging control system can be the cause of malfunction

      Previous Trip Alternator Max Output Time

      Generator maximum generating time during previous drive

      Min.: 0 sec.

      Max.: 65535 sec.

      -

      w/ Stop and Start System

      Initial Engine Battery Minimum Voltage

      Minimum battery voltage at engine start

      Min.: 0.0 V

      Max.: 25.5 V

      -

      w/ Stop and Start System

      Previous Trip Charge Control Time

      Charging control time during previous drive

      Min.: 0 sec.

      Max.: 65535 sec.

      -

      w/ Stop and Start System

      Previous Trip Average Battery Temperature

      Battery average temperature during previous drive

      Min.: -40°C (-40°F)

      Max.: 215°C (419°F)

      -

      w/ Stop and Start System

      Tip:

      Normal Condition: If no idling conditions are specified, the shift lever should be in N (Neutral) or P, and the A/C switch and all accessory switches should be off.

  2. ACTIVE TEST

    Tip:

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine / Active Test.

    5. According to the display on the GTS, perform the Active Test.

      Powertrain > Engine > Active Test

      Tester Display

      Measurement Item

      Control Range

      Diagnostic Note

      Control the Voltage of Alternator

      Requested output voltage of generator regulator during forced activation

      Between 12.5 and 14.8 V

      Test is possible after engine start