ENGINE UNIT(w/o Glow Plug Controller) REASSEMBLY

PROCEDURE

  1. INSTALL OIL PAN SUB-ASSEMBLY

    1. Apply seal packing to the oil pan sub-assembly in a continuous line as shown in the illustration.

      A286870N01

      Standard Seal Packing Diameter

      Area

      Bead Size

      mm (in.)

      A - A

      2.0 to 3.0

      (0.0787 to 0.118)

      B - B

      Min. Width: 7.0 (0.276)

      Min. Height: 3.0 (0.118)

      Seal packing

      Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

      Note:
      • Remove any oil from the contact surfaces.

      • Install the oil pan within 3 minutes, and tighten the bolts within 15 minutes of applying the seal packing.

      • Do not start the engine for at least 2 hours after installing the oil pan sub-assembly.

    2. A286871E01

      Using several steps, temporarily tighten the 12 bolts, and then tighten them to the specified torque in the order shown in the illustration.

      21 N*m

      214 kgf*cm

      15 ft.*lbf

      Bolt Length

      Bolt

      Length

      mm (in.)

      A

      35 (1.378)

      B

      143.7 (5.657)

      C

      119 (4.685)

  2. INSTALL ENGINE REAR OIL SEAL

  3. INSTALL ENGINE OIL LEVEL SENSOR

    1. A299636C01

      *1

      Gasket

      *2

      Engine Oil level Sensor

      *a

      Engine Oil level Sensor Side

      *b

      Float Side

      *c

      Groove

      Install a new gasket to the engine oil level sensor.

      Note:

      Securely install the gasket to the engine oil level sensor groove.

    2. A294024N01

      Temporarily tighten the engine oil level sensor with the 5 bolts.

      Note:

      Do not deform the engine oil level sensor float or allow it to come in contact with other parts.

    3. Fully tighten the 4 bolts (A) first, and then the bolt (B).

      11 N*m

      112 kgf*cm

      8 ft.*lbf

  4. INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

    1. A198432C03

      *a

      Seal Packing

      Apply seal packing (diameter 2.5 to 3.5 mm (0.0984 to 0.138 in.)) to the No. 2 oil pan sub-assembly in a continuous line as shown in the illustration.

      Seal packing

      Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

      Note:
      • Remove any oil from the contact surfaces.

      • Install the No. 2 oil pan sub-assembly within 3 minutes, and tighten the bolts within 10 minutes of applying the seal packing.

      • Do not start the engine for at least 2 hours after installing the No. 2 oil pan sub-assembly.

    2. Temporarily tighten the No. 2 oil pan sub-assembly with the 10 bolts and 2 nuts.

    3. A200097C01

      Fully tighten the 10 bolts and 2 nuts, as shown in the illustration.

      9.0 N*m

      92 kgf*cm

      80 in.*lbf

    4. Install a new gasket and oil pan drain plug.

      38 N*m

      387 kgf*cm

      28 ft.*lbf

  5. INSTALL OIL FILTER BRACKET SUB-ASSEMBLY

    1. Check and clean the oil filter bracket sub-assembly installation surface.

    2. A200031

      Install a new gasket to the oil pan sub-assembly.

    3. A200030

      Install the oil filter bracket sub-assembly with the 2 bolts.

      21 N*m

      214 kgf*cm

      15 ft.*lbf

  6. INSTALL OIL COOLER ASSEMBLY

    1. Check and clean the oil cooler assembly installation surface.

    2. A200029

      Install 2 new O-rings and a new gasket to the oil filter bracket sub-assembly.

    3. A200028

      Install the oil cooler assembly with the 2 bolts and 2 nuts.

      21 N*m

      214 kgf*cm

      15 ft.*lbf

  7. INSTALL OIL FILTER ELEMENT

  8. INSTALL CYLINDER BLOCK WATER JACKET SPACER

    1. A198503

      Install the cylinder block water jacket spacer to the cylinder block sub-assembly.

  9. INSTALL CYLINDER HEAD GASKET

  10. INSTALL CYLINDER HEAD SUB-ASSEMBLY

    1. Apply a light coat of engine oil to the threads of the 10 cylinder head set bolts.

    2. A200012C03

      *a

      Paint Mark

      V100136

      Front

      Using several steps, install and uniformly tighten the 10 cylinder head set bolts and 10 plate washers in the order shown in the illustration. (*1)

      50 N*m

      510 kgf*cm

      37 ft.*lbf

    3. Mark the front of the 10 cylinder head set bolts with paint.

    4. Using the same order as step (*1), tighten the 10 cylinder head set bolts an additional 90°.

    5. Repeat the step above 2 more times as shown in the illustration.

    6. Check that each paint mark is now 270° from the front.

  11. INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

    1. G035835

      Apply engine oil to the valve stem end caps, No. 1 valve rocker arm sub-assembly pivot top surfaces and No. 1 valve rocker arm sub-assembly roller portions.

    2. Install the 8 No. 1 valve rocker arm sub-assemblies.

  12. INSTALL CAMSHAFT

  13. INSTALL CHAIN DAMPER SPRING

    1. A198518

      Install the chain damper spring to the chain tensioner plate.

  14. INSTALL NO. 2 CHAIN SUB-ASSEMBLY

    1. A286877C02

      *1

      Key

      *a

      TDC Mark

      *b

      Oil Pump Shaft

      *c

      Flat Side

      Align the crankshaft key with the TDC mark on the cylinder block sub-assembly.

    2. Rotate the oil pump shaft so that the flat side faces left when viewing the cylinder block sub-assembly from the front.

    3. A198513C03

      *1

      Oil Pump Drive Gear

      *2

      Oil Pump Drive Shaft Gear

      *a

      Timing Mark

      *b

      Orange Mark Plate

      Align the orange mark plates with the timing mark of each gear as shown in the illustration.

    4. A198514

      Install the sprockets onto the crankshaft and oil pump shaft with the No. 2 chain sub-assembly wrapped around the gears.

    5. A198516

      Insert a 4 mm (0.157 in.) diameter bar into the adjusting hole of the oil pump drive shaft gear to lock the gear in position, and then tighten the nut.

      30 N*m

      306 kgf*cm

      22 ft.*lbf

    6. A286878C02

      *1

      Chain Tensioner Plate

      *2

      Chain Damper Spring

      *a

      Pin

      *b

      Pivot Hole

      Install the chain tensioner plate with the chain damper spring to the pin.

      Note:
      • Push the chain tensioner plate so that the area around the pivot hole reaches the base of the pin.

      • The end of the chain damper spring should contact the side of the oil pan sub-assembly so that tension is applied to the No. 2 chain sub-assembly.

    7. A286879C02

      *1

      Key

      *a

      Timing Mark

      *b

      Mark Plate

      *c

      TDC Mark

      Check that the mark plates and timing marks are in the positions shown in the illustration.

  15. INSTALL CHAIN SUB-ASSEMBLY

    1. G102122C02

      *a

      Straight Pin

      Turn the camshaft to set the straight pin in the position shown in the illustration.

    2. A286880C03

      *1

      Key

      *a

      Turn

      *b

      TDC Mark

      Turn the crankshaft to set the key in the position shown in the illustration.

    3. A286881C02

      *a

      Timing Mark

      *b

      Orange Mark Plate

      *c

      Yellow Mark Plate

      Align the 2 orange mark plates with the timing mark on the camshaft timing sprocket, and the yellow mark plate with the timing mark on the crankshaft timing sprocket.

    4. A286882C02

      *a

      Timing Mark

      *b

      Orange Mark Plate

      *c

      Yellow Mark Plate

      Install the chain sub-assembly, camshaft timing sprocket and crankshaft timing sprocket together onto the engine.

    5. A198523E01

      w/o Stop And Start System

      1. Using SST, secure the camshaft timing sprocket, and install the camshaft timing sprocket with the 3 bolts.

        09960-10010

        09962-01000

        09963-01000

        20 N*m

        204 kgf*cm

        15 ft.*lbf

    6. A297909

      w/ Stop And Start System

      1. Install the 3 bolts while holding the hexagonal portion of the camshaft, and then install the camshaft timing sprocket and sensor plate.

        20 N*m

        204 kgf*cm

        15 ft.*lbf

  16. INSTALL NO. 1 CHAIN VIBRATION DAMPER

    1. A296125

      Install the No. 1 chain vibration damper with the 2 bolts.

      21 N*m

      214 kgf*cm

      15 ft.*lbf

  17. INSTALL CHAIN TENSIONER SLIPPER

    1. A198525

      Install the chain tensioner slipper to the cylinder block sub-assembly.

  18. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

    1. A200013C04

      *a

      Push

      *b

      Plunger

      *c

      Groove

      *d

      Hole

      Push in the plunger until the groove is aligned with the hole, and then insert a 1.1 mm (0.0433 in.) diameter bar.

    2. A198527

      Install the No. 1 chain tensioner assembly with the 2 bolts.

      21 N*m

      214 kgf*cm

      15 ft.*lbf

    3. Remove the 1.1 mm (0.0433 in.) diameter bar from the No. 1 chain tensioner assembly.

    4. A286883C02

      *a

      Timing Mark

      *b

      Orange Mark Plate

      *c

      Yellow Mark Plate

      Check that the mark plates and timing marks are in the positions shown in the illustration.

  19. INSTALL INLET WATER HOUSING

    1. Install a new No. 2 water inlet housing gasket to the inlet water housing.

    2. A255685

      Install the inlet water housing to the timing chain cover sub-assembly with the 3 bolts.

      9.0 N*m

      92 kgf*cm

      80 in.*lbf

  20. INSTALL OIL CHECK VALVE SUB-ASSEMBLY

    1. Using a 6 mm hexagon socket wrench, install the oil check valve sub-assembly with the bolt.

      9.0 N*m

      92 kgf*cm

      80 in.*lbf

  21. INSTALL TIMING CHAIN COVER OIL SEAL

    1. Apply MP grease to a new timing chain cover oil seal lip.

      Note:

      Keep the lip free from foreign matter.

    2. A295790N01

      Using SST and a hammer, tap in the new timing chain cover oil seal until its surface is flush with the timing chain cover sub-assembly edge.

      09223-22010

      Oil seal tap in depth

      -1.0 to 0 mm (-0.0394 to 0 in.)

      Note:
      • Do not tap in the timing chain cover oil seal at an angle.

      • Wipe off extra grease from the crankshaft.

  22. INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

    1. A246051

      Install the new oil pump gasket.

    2. Apply seal packing to the engine body and oil pump as shown in the illustration below.

      A294027C03

      *a

      Seal Width (Toyota Genuine Seal Packing Black, Three Bond 1207B)

      *b

      Seal Width (Toyota Genuine Seal Packing 1282B, Three Bond 1282B)

      *c

      Width

      *d

      Height

      *e

      Double Line Area

      -

      -

      Note:
      • Remove any oil from the contact surfaces.

      • Install the timing chain cover sub-assembly within 3 minutes, and tighten the bolts within 15 minutes of applying the seal packing.

      • Do not start the engine for at least 2 hours after installing the timing chain cover sub-assembly.

      Seal packing

      Engine water pump assembly: Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent

      Other: Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    3. Install the timing chain cover sub-assembly with the 20 bolts and 2 nuts, as shown in the illustration.

      A294028C01

      *1

      Nut

      -

      -

      Bolt A, B, Nut

      21 N*m

      214 kgf*cm

      15 ft.*lbf

      Bolt C

      40 N*m

      408 kgf*cm

      30 ft.*lbf

      Bolt Length

      Bolt

      Length

      mm (in.)

      A

      25 (0.984)

      B

      35 (1.378)

      C

      40 (1.575)

      Note:
      • Make sure that the chain sub-assembly and No. 2 chain sub-assembly do not come into contact with the seal packing when installing the timing chain cover sub-assembly.

      • Install the engine mounting bracket RH within 10 minutes of installing the timing chain cover sub-assembly.

  23. INSTALL CRANKSHAFT DAMPER SUB-ASSEMBLY

  24. INSTALL OIL PRESSURE SWITCHING VALVE ASSEMBLY

    1. A239526C02

      *a

      O-ring

      Apply a light coat of engine oil to the O-ring of the oil pressure switching valve assembly.

    2. Install the oil pressure switching valve assembly with the bolt.

      9.0 N*m

      92 kgf*cm

      80 in.*lbf

      Note:

      Make sure that the O-ring is not torn or pinched when installing.

  25. INSTALL NO. 2 TIMING CHAIN COVER

    1. A246055

      Install the No. 2 timing chain cover with the harness bracket and bolt.

      9.0 N*m

      92 kgf*cm

      80 in.*lbf

  26. INSTALL ENGINE MOUNTING BRACKET RH

    1. A200032N01

      Temporarily tighten the engine mounting bracket RH with the 4 bolts.

    2. Fully tighten the 4 bolts, as shown in the illustration.

      55 N*m

      561 kgf*cm

      41 ft.*lbf

  27. INSTALL OIL PRESSURE SENDER GAGE ASSEMBLY

    1. P101007C04

      *a

      Adhesive

      Apply adhesive to 2 or 3 threads of the oil pressure sender gage assembly.

      Adhesive

      Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

    2. A248777

      Using a 27 mm deep socket wrench, install the oil pressure sender gage assembly.

      15 N*m

      153 kgf*cm

      11 ft.*lbf

  28. INSTALL WATER INLET

    1. Install a new No. 1 water inlet housing gasket to the water inlet.

    2. A246056

      Install the water inlet with the 3 bolts.

      9.0 N*m

      92 kgf*cm

      80 in.*lbf

  29. INSTALL OUTLET WATER SUB-ASSEMBLY

    1. Install a new water outlet gasket to the cylinder head sub-assembly.

    2. A205754

      Install the outlet water sub-assembly with the 2 bolts and 2 nuts.

      11 N*m

      112 kgf*cm

      8 ft.*lbf

  30. INSTALL WATER TEMPERATURE SENSOR

    1. Install a new gasket to the water temperature sensor.

    2. A205753

      Using a 19 mm deep socket wrench, install the water temperature sensor.

      19.6 N*m

      200 kgf*cm

      14 ft.*lbf

  31. CHECK VALVE CLEARANCE

  32. ADJUST VALVE CLEARANCE

  33. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

    1. Install the cylinder head gasket to the cylinder head cover sub-assembly.

    2. A286818C01
      V100135

      Seal Packing

      Apply seal packing to the 4 locations shown in the illustration, and then install the cylinder head cover sub-assembly.

      Seal packing

      Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

      Note:
      • Remove any oil from the contact surfaces.

      • Install the cylinder head cover sub-assembly within 3 minutes, and tighten the bolts within 15 minutes of applying the seal packing.

      • Do not start the engine for at least 2 hours after installing the cylinder head cover sub-assembly.

    3. A294029N01

      Temporarily tighten the cylinder head cover sub-assembly with the 12 bolts.

    4. Fully tighten the 12 bolts in the order shown in the illustration.

      11 N*m

      112 kgf*cm

      8 ft.*lbf

  34. INSTALL OIL FILLER CAP SUB-ASSEMBLY

    1. Install the oil filler cap gasket to the oil filler cap sub-assembly.

    2. Install the oil filler cap sub-assembly to the cylinder head cover sub-assembly.