SFI SYSTEM, Diagnostic DTC:P001600 and P001700
| DTC Code | DTC Name |
|---|---|
| P001600 | Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor A |
| P001700 | Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor B |
DESCRIPTION
In the VVT (Variable Valve Timing) system, the appropriate intake and exhaust valve open and close timing is controlled by the ECM. The ECM performs intake and exhaust valve control by performing the following: 1) controlling the camshaft, cam timing oil control solenoid assembly, camshaft timing gear bolt (camshaft timing oil control valve assembly) and operating the camshaft timing gear; and 2) changing the relative positions of the camshaft and crankshaft.
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
MIL |
Memory |
Note |
|---|---|---|---|---|---|---|
P001600 |
Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor A |
Deviation in the crankshaft position sensor signal and camshaft sensor (for intake camshaft) signal (2 trip detection logic). |
|
Comes on |
DTC stored |
SAE Code: P0016 |
P001700 |
Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor B |
Deviation in the crankshaft position sensor signal and camshaft position sensor (for exhaust camshaft) signal (2 trip detection logic). |
|
Comes on |
DTC stored |
SAE Code: P0017 |
MONITOR DESCRIPTION
To monitor the correlation of the intake camshaft position and crankshaft position, the ECM checks the VVT learned value while the engine is idling. The VVT learned value is calibrated based on the camshaft position and crankshaft position. The intake valve timing is set to the neutral position while the engine is idling. If the VVT learned value is out of the specified range in consecutive driving cycles, the ECM illuminates the MIL and stores DTC P001600.
To monitor the correlation of the exhaust camshaft position and crankshaft position, the ECM checks the VVT learned value while the engine is idling. The VVT learned value is calibrated based on the camshaft position and crankshaft position. The exhaust valve timing is set to the most advanced angle while the engine is idling. If the VVT learned value is out of the specified range in consecutive driving cycles, the ECM illuminates the MIL and stores DTC P001700.
MONITOR STRATEGY
Required Sensors/Components (Main) |
Camshaft timing gear assembly Camshaft timing exhaust gear assembly |
Required Sensors/Components (Related) |
Camshaft position sensor Crankshaft position sensor |
Frequency of Operation |
Continuous |
TYPICAL ENABLING CONDITIONS
Engine speed |
500 to 1000 rpm |
CONFIRMATION DRIVING PATTERN
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS on [A].
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].
Idle the engine for 5 minutes or more [C].
Enter the following menus: Powertrain / Engine / Trouble Codes [D].
Read the pending DTCs.
Tip:If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P001600 or P001700.
Check the DTC judgment result.
GTS Display
Description
NORMAL
DTC judgment completed
System normal
ABNORMAL
DTC judgment completed
System abnormal
INCOMPLETE
DTC judgment not completed
Perform driving pattern after confirming DTC enabling conditions
N/A
Unable to perform DTC judgment
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
Tip:If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform steps [E] through [G].
Drive the vehicle for 2 to 3 minutes [E].
CAUTION:When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Idle the engine for 5 minutes or more [F].
Enter the following menus: Powertrain / Engine / Trouble Codes [G].
Read the pending DTCs.
Tip:If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Check the DTC judgment result.
Tip:If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
CAUTION / NOTICE / HINT
The monitor for this DTC detects when the timing chain is shifted by two teeth or more.
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P001600 OR P001700)
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
Powertrain > Engine > Trouble Codes
Result
Result
Proceed to
DTC P001600 or P001700 is output
A
DTC P001600 or P001700 and other DTCs are output
B
Tip:If any DTCs other than P001600 or P001700 is output, troubleshoot those DTCs first.
PERFORM ACTIVE TEST USING GTS (CONTROL THE INTAKE VVT OCV DUTY RATIO BANK 1 OR CONTROL THE EXHAUST VVT OCV DUTY RATIO BANK 1)
Tip:If the VVT system can be operated through the Active Test, it can be assumed that the VVT system is operating normally.
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Control the Intake VVT OCV Duty Ratio Bank 1 or Control the Exhaust VVT OCV Duty Ratio Bank 1 / Data List / All Data / Intake VVT Change Angle Bank 1 or Exhaust VVT Change Angle Bank 1.
Powertrain > Engine > Active Test
Active Test Display
Control the Intake VVT OCV Duty Ratio Bank 1
Data List Display
Intake VVT Change Angle Bank 1
Powertrain > Engine > Active Test
Active Test Display
Control the Exhaust VVT OCV Duty Ratio Bank 1
Data List Display
Exhaust VVT Change Angle Bank 1
Perform the Active Test. Check that the displacement angle varies.
OK
Displacement angle varies.
Result
Proceed to
OK
NG
NG INSPECT CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR INTAKE OR EXHAUST CAMSHAFT)Click here
CHECK ENGINE MECHANICAL SYSTEM
Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.
Result
Proceed to
OK
NG
OK CHECK WHETHER DTC OUTPUT RECURS (DTC P001600 OR P001700)Click here
NG REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA
INSPECT CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR INTAKE OR EXHAUST CAMSHAFT)
Inspect the cam timing oil control solenoid assembly (for intake or exhaust camshaft).
Result
Proceed to
OK
NG
INSPECT CAMSHAFT TIMING GEAR BOLT (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY [FOR INTAKE OR EXHAUST CAMSHAFT])
Inspect the camshaft timing gear bolt (camshaft timing oil control valve assembly [for intake or exhaust camshaft]).
for intake camshaft:Click here
for exhaust camshaft:Click here
Result
Proceed to
OK
NG
NG REPLACE CAMSHAFT TIMING GEAR BOLT (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY [FOR INTAKE OR EXHAUST CAMSHAFT])
for intake camshaft:Click here
for exhaust camshaft:Click here
INSPECT OIL CONTROL VALVE FILTER
*1
Oil Control Valve Filter
Remove the oil control valve filter.
Check that the filter is not clogged.
OK
Filter is not clogged.
Result
Proceed to
OK
NG
CHECK WHETHER DTC OUTPUT RECURS (DTC P001600 OR P001700)
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Powertrain > Engine > Clear DTCs
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.
Read the pending DTCs.
Powertrain > Engine > Trouble Codes
Result
Result
Proceed to
DTCs are not output
A
DTC P001600 or P001700 is output
B
REPLACE CAMSHAFT TIMING GEAR ASSEMBLY OR CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
Replace the camshaft timing gear assembly or camshaft timing exhaust gear assembly.
Tip:Perform "Inspection After Repair" after replacing the camshaft timing gear assembly or camshaft timing exhaust gear assembly.
Result
Proceed to
NEXT
CHECK WHETHER DTC OUTPUT RECURS (DTC P001600 OR P001700)
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Powertrain > Engine > Clear DTCs
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.
Read the pending DTCs.
Powertrain > Engine > Trouble Codes
Result
Result
Proceed to
DTCs are not output
A
DTC P001600 or P001700 is output
B
A END