CAMSHAFT(w/ Glow Plug Controller) INSTALLATION

PROCEDURE

  1. INSTALL CAMSHAFT

    1. A350425C01

      *a

      Key

      *b

      Knock Pin

      *c

      75° BTDC

      *d

      Bolt Hole of Timing Chain Cover Sub-assembly

      V100135

      Upper of Engine

      Turn the crankshaft to set the key in the 75° BTDC (aligned with the bolt hole of timing chain cover sub-assembly) position.

    2. Apply engine oil to each camshaft journal portion and cam portion.

    3. Install the camshaft to the cylinder head sub-assembly.

      Note:
      • Do not tilt the No. 1 valve rocker arm sub-assembly when installing the camshaft to the cylinder head sub-assembly.

      • Align the camshaft knock pin towards the top of the engine.

    4. A350426C01

      *1

      No. 1 Camshaft Bearing Cap

      *2

      No. 2 Camshaft Bearing Cap

      *3

      No. 4 Camshaft Bearing Cap

      *a

      Front Mark

      V100135

      Engine Front

      Confirm the front marks and numbers, then place the No. 1 camshaft bearing cap, 3 No. 2 camshaft bearing caps and No. 4 camshaft bearing cap on the camshaft with the front marks facing as shown in the illustration.

    5. Install and uniformly tighten the 10 bolts in several steps in the order shown in the illustration.

      19 N*m

      194 kgf*cm

      14 ft.*lbf

  2. INSTALL CHAIN SUB-ASSEMBLY

  3. INSTALL NO. 1 CHAIN VIBRATION DAMPER

  4. INSTALL CHAIN TENSIONER SLIPPER

  5. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

  6. INSTALL TIMING CHAIN COVER OIL SEAL

  7. INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

  8. CONNECT WATER INLET HOSE LH

    1. Connect the water inlet hose LH to the water inlet and slide the hose clip to secure it.

      Tip:

      The clip on the water inlet side can be installed with any orientation, as long as it does not contact any of the surrounding parts.

  9. INSTALL CRANKSHAFT DAMPER SUB-ASSEMBLY

  10. INSTALL CAMSHAFT POSITION SENSOR

  11. INSTALL NO. 2 TIMING CHAIN COVER

  12. INSTALL ENGINE MOUNTING BRACKET RH

  13. CHECK VALVE CLEARANCE

  14. ADJUST VALVE CLEARANCE

  15. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

  16. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

  17. INSTALL VACUUM PUMP ASSEMBLY

  18. INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY

    1. Install a new O-ring to the water by-pass pipe sub-assembly.

      Note:

      Apply coolant around the water by-pass pipe O-ring groove of the water inlet housing before installing the water by-pass pipe sub-assembly.

    2. Install the water by-pass pipe sub-assembly to the No. 2 turbocharger stay, cylinder head sub-assembly, cylinder block sub-assembly and water inlet housing with the 3 bolts.

      9.0 N*m

      92 kgf*cm

      80 in.*lbf

    3. A265738C01

      *a

      View (A)

      *b

      RH of Engine

      *c

      Front of Engine

      Connect the oil cooler hose to the water by-pass pipe sub-assembly and slide the hose clip to secure it.

    4. A265739C01

      *a

      View (A)

      *b

      Top of Engine

      *c

      Front of Engine

      Connect the water by-pass hose to the tube connector and slide the hose clip to secure it.

    5. A265740C01

      *a

      View (A)

      *b

      Front of Engine

      *c

      LH of Engine

      Connect the No. 6 water by-pass hose to the water by-pass pipe sub-assembly and slide the hose clip to secure it.

  19. INSTALL NO. 4 WATER BY-PASS HOSE

    1. A265741C01

      *a

      View (A)

      *b

      Top of Engine

      *c

      Front of Engine

      Install the No. 4 water by-pass hose to the water inlet pipe and slide the hose clip to secure it.

      Note:

      Perform the installation with the hose clip at the correct angle.

    2. Engage the clamp to connect the No. 4 water by-pass hose to the common rail assembly.

  20. INSTALL NO. 2 OIL COOLER HOSE

  21. INSTALL SUPPLY PUMP ASSEMBLY

  22. INSTALL FUEL PUMP PROTECTOR

  23. INSTALL NO. 2 NOZZLE LEAKAGE PIPE

  24. CONNECT NO. 2 FUEL HOSE

    1. A265734C02

      *a

      View (A)

      *b

      Top of Engine

      *c

      Rear of Engine

      Connect the No. 2 fuel hose to the No. 2 nozzle leakage pipe and slide the hose clip to secure it.

  25. CONNECT NO. 1 FUEL HOSE

  26. INSTALL FUEL INLET PIPE SUB-ASSEMBLY

  27. CONNECT NOZZLE LEAKAGE PIPE ASSEMBLY

  28. INSTALL INTAKE AIR CONNECTOR WITH DIESEL THROTTLE BODY

  29. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

  30. INSTALL ENGINE OIL LEVEL DIPSTICK

  31. INSTALL EGR VALVE (ELECTRIC EGR CONTROL VALVE ASSEMBLY)

  32. INSTALL HARNESS BRACKET (for LHD)

  33. INSTALL HARNESS BRACKET (for RHD)

  34. INSTALL NO. 1 EGR COOLER BRACKET

  35. INSTALL EGR WITH COOLER PIPE ASSEMBLY

  36. INSTALL GENERATOR BRACKET

  37. INSTALL GENERATOR ASSEMBLY

  38. INSTALL ENGINE COVER BRACKET

  39. REMOVE ENGINE FROM ENGINE STAND