SFI SYSTEM, Diagnostic DTC:P001100 and P001200
| DTC Code | DTC Name |
|---|---|
| P001100 | Camshaft Position "A" - Timing Over-Advanced or System Performance Bank 1 |
| P001200 | Camshaft Position "A" - Timing Over-Retarded Bank 1 |
DESCRIPTION
Refer to DTC P001013.
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
MIL |
Memory |
Note |
|---|---|---|---|---|---|---|
P001100 |
Camshaft Position "A" - Timing Over-Advanced or System Performance Bank 1 |
Intake valve timing is stuck at a certain value when in the advance range (1 trip detection logic). |
|
Comes on |
DTC stored |
SAE Code: P0011 |
P001200 |
Camshaft Position "A" - Timing Over-Retarded Bank 1 |
Intake valve timing is stuck at a certain value when in the retard range (1 trip detection logic). |
|
Comes on |
DTC stored |
SAE Code: P0012 |
MONITOR DESCRIPTION
The ECM optimizes the intake valve timing using the Variable Valve Timing (VVT) system to control the intake camshaft. The VVT system includes the ECM, cam timing oil control solenoid assembly (for intake camshaft), camshaft timing gear bolt (camshaft timing oil control valve assembly [for intake camshaft]) and camshaft timing gear assembly. The ECM sends a target duty-cycle control signal to the cam timing oil control solenoid assembly (for intake camshaft). The camshaft timing gear bolt (camshaft timing oil control valve assembly [for intake camshaft]) is operated to control the oil pressure supplied to the camshaft timing gear assembly based on this signal. The camshaft timing gear assembly can advance or retard the intake camshaft.
If the difference between the target and actual intake valve timing is large, and changes in the actual intake valve timing are small, the ECM interprets this as the camshaft timing gear assembly stuck malfunction and stores a DTC.
Example:
DTC P001100 is stored when the following conditions are met:
It takes 5 seconds or more for intake valve timing to change 5 deg(CA).
After the malfunction condition above has been detected, the same condition continues 9.5 seconds or more.
DTC P001200 is stored when the following conditions are met:
It takes 5 seconds or more for intake valve timing to change 5 deg(CA).
After the malfunction condition above has been detected, the same condition continues 60 seconds or more.
These DTCs indicate that the camshaft timing gear assembly cannot operate properly due to a camshaft timing gear bolt (camshaft timing oil control valve assembly [for intake camshaft]) malfunction or the presence of foreign matter in the camshaft timing gear bolt (camshaft timing oil control valve assembly [for intake camshaft]).
MONITOR STRATEGY
Required Sensors/Components (Main) |
Cam timing oil control solenoid assembly (for intake camshaft) Camshaft timing gear bolt (camshaft timing oil control valve assembly [for intake camshaft]) Crankshaft timing gear assembly |
Required Sensors/Components (Related) |
Crankshaft position sensor Camshaft position sensor Engine coolant temperature sensor |
Frequency of Operation |
Continuous |
CONFIRMATION DRIVING PATTERN
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS on [A].
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].
Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [C].
CAUTION:When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Idle the engine for 3 minutes or more [D].
Enter the following menus: Powertrain / Engine / Trouble Codes [E].
Read the pending DTCs.
Tip:If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P001100 or P0001200.
Check the DTC judgment result.
GTS Display
Description
NORMAL
DTC judgment completed
System normal
ABNORMAL
DTC judgment completed
System abnormal
INCOMPLETE
DTC judgment not completed
Perform driving pattern after confirming DTC enabling conditions
N/A
Unable to perform DTC judgment
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
Tip:If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform steps [F] through [H].
Repeat the pattern of accelerating the vehicle from rest to approximately 60 km/h (37 mph) and then decelerating the vehicle 10 to 15 times [F].
CAUTION:When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Tip:Depress the accelerator pedal by a large amount.
Idle the engine for 3 minutes or more [G].
Enter the following menus: Powertrain / Engine / Trouble Codes [H].
Read the pending DTCs.
Tip:If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Check the DTC judgment result again.
Tip:If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
WIRING DIAGRAM
Refer to DTC P001013.
CAUTION / NOTICE / HINT
DTC P001100 or P001200 may be stored when foreign matter in the engine oil is caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. That foreign matter may then be captured by the oil filter.
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P001100 OR P001200)
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
Powertrain > Engine > Trouble Codes
Result
Result
Proceed to
DTC P001100 or P001200 is output
A
DTC P001100 or P001200 and other DTCs are output
B
Tip:If any DTCs other than P001100 or P001200 are output, troubleshoot those DTCs first.
PERFORM ACTIVE TEST USING GTS (CONTROL THE INTAKE VVT OCV DUTY RATIO BANK 1)
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Control the Intake VVT OCV Duty Ratio Bank 1 / Data List / All Data / Intake VVT Change Angle Bank 1.
Powertrain > Engine > Active Test
Active Test Display
Control the Intake VVT OCV Duty Ratio Bank 1
Data List Display
Intake VVT Change Angle Bank 1
Read the Data List while performing the Active Test with the engine idling.
OK
GTS Operation
Data List (Intake VVT Change Angle Bank 1)
-100% to 100%
Varies by 70 DegFR or more
Result
Proceed to
OK
NG
NG INSPECT CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR INTAKE CAMSHAFT)Click here
CHECK WHETHER DTC OUTPUT RECURS (DTC P001100 OR P001200)
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Powertrain > Engine > Clear DTCs
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
Powertrain > Engine > Trouble Codes
Result
Result
Proceed to
DTCs are not output
A
DTC P001100 or P001200 is output
B
Tip:DTC P001100 or P001200 may be stored when foreign matter in the engine oil is caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. That foreign matter may then be captured by the oil filter.
B INSPECT CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR INTAKE CAMSHAFT)Click here
INSPECT CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR INTAKE CAMSHAFT)
Inspect the cam timing oil control solenoid assembly (for intake camshaft).
Result
Proceed to
OK
NG
NG REPLACE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR INTAKE CAMSHAFT)Click here
INSPECT CAMSHAFT TIMING GEAR BOLT (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY [FOR INTAKE CAMSHAFT])
Inspect the camshaft timing gear bolt (camshaft timing oil control valve assembly [for intake camshaft]).
Result
Proceed to
OK
NG
NG REPLACE CAMSHAFT TIMING GEAR BOLT (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY [FOR INTAKE CAMSHAFT])Click here
INSPECT OIL CONTROL VALVE FILTER
*1
Oil Control Valve Filter
Remove the oil control valve filter.
Check that the filter is not clogged.
OK
Filter is not clogged.
Result
Proceed to
OK
NG
OK REPLACE CAMSHAFT TIMING GEAR ASSEMBLYClick here
REPLACE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR INTAKE CAMSHAFT)
Replace the cam timing oil control solenoid assembly (for intake camshaft).
Result
Proceed to
NEXT
INSPECT CAMSHAFT TIMING GEAR BOLT (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY [FOR INTAKE CAMSHAFT])
Inspect the camshaft timing gear bolt (camshaft timing oil control valve assembly [for intake camshaft]).
Result
Proceed to
OK
NG
OK PERFORM ACTIVE TEST USING GTS (CONTROL THE INTAKE VVT OCV DUTY RATIO BANK 1)Click here
REPLACE CAMSHAFT TIMING GEAR BOLT (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY [FOR INTAKE CAMSHAFT])
Replace the camshaft timing gear bolt (camshaft timing oil control valve assembly [for intake camshaft]).
Result
Proceed to
NEXT
PERFORM ACTIVE TEST USING GTS (CONTROL THE INTAKE VVT OCV DUTY RATIO BANK 1)
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Control the Intake VVT OCV Duty Ratio Bank 1 / Data List / All Data / Intake VVT Change Angle Bank 1.
Powertrain > Engine > Active Test
Active Test Display
Control the Intake VVT OCV Duty Ratio Bank 1
Data List Display
Intake VVT Change Angle Bank 1
Read the Data List while performing the Active Test with the engine idling.
OK
GTS Operation
Data List (Intake VVT Change Angle Bank 1)
-100% to 100%
Varies by 70 DegFR or more
Result
Proceed to
OK
NG
OK END
REPLACE CAMSHAFT TIMING GEAR ASSEMBLY
Replace the camshaft timing gear assembly.
Tip:Perform "Inspection After Repair" after replacing the camshaft timing gear assembly.
Result
Proceed to
NEXT
CHECK WHETHER DTC OUTPUT RECURS (DTC P001100 OR P001200)
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Powertrain > Engine > Clear DTCs
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
Powertrain > Engine > Trouble Codes
Result
Result
Proceed to
DTCs are not output
A
DTC P001100 or P001200 is output
B
A END
CHECK ENGINE MECHANICAL SYSTEM
Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.
Result
Proceed to
OK
NG
NG REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA
CHECK WHETHER DTC OUTPUT RECURS (DTC P001100 OR P001200)
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Powertrain > Engine > Clear DTCs
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
Powertrain > Engine > Trouble Codes
Result
Result
Proceed to
DTCs are not output
A
DTC P001100 or P001200 is output
B