CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM(for 1ZR-FAE), Diagnostic DTC:P0841 and P2829
| DTC Code | DTC Name |
|---|---|
| P0841 | Transmission Fluid Pressure Sensor "A" Performance |
| P2829 | Pressure Control Solenoid "K" Performance (Shift Solenoid Valve SLS) |
DESCRIPTION
The ECM controls the secondary oil pressure based on the secondary oil pressure signal output by the oil pressure sensor.
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
MIL |
Memory |
|---|---|---|---|---|---|
P0841 |
Transmission Fluid Pressure Sensor "A" Performance |
1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
|
|
Comes on |
DTC stored |
P2829 |
Pressure Control Solenoid "K" Performance (Shift Solenoid Valve SLS) |
1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
|
|
Comes on |
DTC stored |
MONITOR DESCRIPTION
The ECM checks for belt clamping high-pressure or low-pressure malfunctions. If a mechanical malfunction of the shift solenoid valve SLS or the oil pressure sensor is detected by the ECM, it illuminates the MIL and stores a DTC.
CAUTION / NOTICE / HINT
After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
Perform the D position test in Road Test.
Check for DTCs again.
PROCEDURE
CHECK DTC OUTPUT (IN ADDITION TO DTC P0841 AND P2829)
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Powertrain > Engine and ECT > Trouble Codes
Read the DTCs using the GTS.
Tip:If any DTCs other than P0841 or P2829 are output, perform troubleshooting for those DTCs first.
Result
Result
Proceed to
Both DTC P0841 and P2829 are output
A
Only DTC P0841 is output
B
Only DTC P2829 is output
C
DTC P0841 and/or P2829 and other DTCs are output
D
B READ VALUE USING GTS (A/T OIL PRESSURE)Click here
C READ VALUE USING GTS (A/T OIL PRESSURE)Click here
READ VALUE USING GTS (A/T OIL PRESSURE)
CAUTION:A stall speed test should always be performed with at least 2 people. One person should observe the condition of the wheels and wheel chocks while the other is performing the test.
Note:This test must be performed after checking and confirming that the engine is normal.
Perform this test with the CVT fluid temperature between 50 and 100°C (122 and 212°F).
Perform this test with the air conditioning off.
Do not perform the stall speed test for longer than 5 seconds
When performing the stall speed test repeatedly, wait for 15 seconds or more between tests.
Warm up the engine.
Fully apply the parking brake and chock all 4 wheels.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1.
Powertrain > Engine and ECT > Active Test
Active Test Display
Connect the TC and TE1
Data List Display
A/T Oil Pressure
According to the display on the GTS, perform the Active Test.
According to the display on the GTS, read the Data List.
Powertrain > Engine and ECT > Data List
Tester Display
Measurement Item
Range
Normal Condition
Diagnostic Note
A/T Oil Pressure
Secondary oil pressure value
Min.: -64 MPa
Max.: 63.998 MPa
Secondary oil pressure inspection:
2.8 to 4.8 MPa (28.5 to 49.0 kgf/cm2, 406 to 697 psi): D position stall test
2.9 to 4.8 MPa (29.5 to 49.0 kgf/cm2, 420 to 697 psi): R position stall test
-
Result
Result
Proceed to
Data List value is normal
A
Data List value is not normal
B
B REPLACE OIL PRESSURE SENSORClick here
REPLACE ECM
Replace the ECM.
Result
Proceed to
NEXT
REPLACE OIL PRESSURE SENSOR
Replace the oil pressure sensor.
Result
Proceed to
NEXT
CLEAR DTC
Clear the DTCs.
Powertrain > Engine and ECT > Clear DTCs
Result
Proceed to
NEXT
PERFORM INITIALIZATION
Note:Performing Reset Memory will clear the learned values of the yaw rate and acceleration sensor (Deceleration Sensor Zero Point Calibration) and the CVT oil pressure (CVT Oil Pressure Calibration). Make sure to perform Reset Memory, Deceleration Sensor Zero Point Calibration, and CVT Oil Pressure Calibration if any of the parts in the following table have been replaced.
Replaced Part
Continuously variable transaxle assembly
ECM
Oil pressure sensor
Airbag sensor assembly (Yaw rate and acceleration sensor)
After performing Reset Memory, always perform Deceleration Sensor Zero Point Calibration first, and then CVT Oil Pressure Calibration.
Always perform calibration with the vehicle on level ground (Inclination: 0 +/- 0.25°).
Do not shake or vibrate the vehicle during calibration.
Using the GTS, perform Reset Memory, Deceleration Sensor Zero Point Calibration and CVT Oil Pressure Calibration.
Result
Proceed to
NEXT
CHECK DTC OUTPUT
Perform a road test.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Powertrain > Engine and ECT > Trouble Codes
Read the DTCs using the GTS.
Result
Result
Proceed to
DTC P0841 and/or P2829 is output
A
DTCs are not output
B
B END
REPLACE ECM
Replace the ECM.
Result
Proceed to
NEXT
PERFORM INITIALIZATION
Note:Performing Reset Memory will clear the learned values of the yaw rate and acceleration sensor (Deceleration Sensor Zero Point Calibration) and the CVT oil pressure (CVT Oil Pressure Calibration). Make sure to perform Reset Memory, Deceleration Sensor Zero Point Calibration, and CVT Oil Pressure Calibration if any of the parts in the following table have been replaced.
Replaced Part
Continuously variable transaxle assembly
ECM
Oil pressure sensor
Airbag sensor assembly (Yaw rate and acceleration sensor)
After performing Reset Memory, always perform Deceleration Sensor Zero Point Calibration first, and then CVT Oil Pressure Calibration.
Always perform calibration with the vehicle on level ground (Inclination: 0 +/- 0.25°).
Do not shake or vibrate the vehicle during calibration.
Using the GTS, perform Reset Memory, Deceleration Sensor Zero Point Calibration and CVT Oil Pressure Calibration.
Result
Proceed to
NEXT
CHECK DTC OUTPUT
Perform a road test.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Powertrain > Engine and ECT > Trouble Codes
Read the DTCs using the GTS.
Result
Result
Proceed to
DTC P2829 is output
A
DTCs are not output
B
B END
REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
Replace the continuously variable transaxle assembly.
Result
Proceed to
NEXT
READ VALUE USING GTS (A/T OIL PRESSURE)
CAUTION:A stall speed test should always be performed with at least 2 people. One person should observe the condition of the wheels and wheel chocks while the other is performing the test.
Note:This test must be performed after checking and confirming that the engine is normal.
Perform this test with the CVT fluid temperature between 50 and 100°C (122 and 212°F).
Perform this test with the air conditioning off.
Do not perform the stall speed test for longer than 5 seconds
When performing the stall speed test repeatedly, wait for 15 seconds or more between tests.
Warm up the engine.
Fully apply the parking brake and chock all 4 wheels.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1.
Powertrain > Engine and ECT > Active Test
Active Test Display
Connect the TC and TE1
Data List Display
A/T Oil Pressure
According to the display on the GTS, perform the Active Test.
According to the display on the GTS, read the Data List.
Powertrain > Engine and ECT > Data List
Tester Display
Measurement Item
Range
Normal Condition
Diagnostic Note
A/T Oil Pressure
Secondary oil pressure value
Min.: -64 MPa
Max.: 63.998 MPa
Secondary oil pressure inspection:
2.8 to 4.8 MPa (28.5 to 49.0 kgf/cm2, 406 to 697 psi): D position stall test
2.9 to 4.8 MPa (29.5 to 49.0 kgf/cm2, 420 to 697 psi): R position stall test
-
Result
Result
Proceed to
Data List value is normal
A
Data List value is not normal
B
B REPLACE OIL PRESSURE SENSORClick here
REPLACE ECM
Replace the ECM.
Result
Proceed to
NEXT
REPLACE OIL PRESSURE SENSOR
Replace the oil pressure sensor.
Result
Proceed to
NEXT
CLEAR DTC
Clear the DTCs.
Powertrain > Engine and ECT > Clear DTCs
Result
Proceed to
NEXT
PERFORM INITIALIZATION
Note:Performing Reset Memory will clear the learned values of the yaw rate and acceleration sensor (Deceleration Sensor Zero Point Calibration) and the CVT oil pressure (CVT Oil Pressure Calibration). Make sure to perform Reset Memory, Deceleration Sensor Zero Point Calibration, and CVT Oil Pressure Calibration if any of the parts in the following table have been replaced.
Replaced Part
Continuously variable transaxle assembly
ECM
Oil pressure sensor
Airbag sensor assembly (Yaw rate and acceleration sensor)
After performing Reset Memory, always perform Deceleration Sensor Zero Point Calibration first, and then CVT Oil Pressure Calibration.
Always perform calibration with the vehicle on level ground (Inclination: 0 +/- 0.25°).
Do not shake or vibrate the vehicle during calibration.
Using the GTS, perform Reset Memory, Deceleration Sensor Zero Point Calibration and CVT Oil Pressure Calibration.
Result
Proceed to
NEXT
CHECK DTC OUTPUT
Perform a road test.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Powertrain > Engine and ECT > Trouble Codes
Read the DTCs using the GTS.
Result
Result
Proceed to
DTC P0841 is output
A
DTCs are not output
B
B END
REPLACE ECM
Replace the ECM.
Result
Proceed to
NEXT
READ VALUE USING GTS (A/T OIL PRESSURE)
CAUTION:A stall speed test should always be performed with at least 2 people. One person should observe the condition of the wheels and wheel chocks while the other is performing the test.
Note:This test must be performed after checking and confirming that the engine is normal.
Perform this test with the CVT fluid temperature between 50 and 100°C (122 and 212°F).
Perform this test with the air conditioning off.
Do not perform the stall speed test for longer than 5 seconds
When performing the stall speed test repeatedly, wait for 15 seconds or more between tests.
Warm up the engine.
Fully apply the parking brake and chock all 4 wheels.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1.
Powertrain > Engine and ECT > Active Test
Active Test Display
Connect the TC and TE1
Data List Display
A/T Oil Pressure
According to the display on the GTS, perform the Active Test.
According to the display on the GTS, read the Data List.
Powertrain > Engine and ECT > Data List
Tester Display
Measurement Item
Range
Normal Condition
Diagnostic Note
A/T Oil Pressure
Secondary oil pressure value
Min.: -64 MPa
Max.: 63.998 MPa
Secondary oil pressure inspection:
2.8 to 4.8 MPa (28.5 to 49.0 kgf/cm2, 406 to 697 psi): D position stall test
2.9 to 4.8 MPa (29.5 to 49.0 kgf/cm2, 420 to 697 psi): R position stall test
-
Result
Result
Proceed to
Data List value is normal
A
Data List value is not normal
B
B REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLYClick here
REPLACE ECM
Replace the ECM.
Result
Proceed to
NEXT
REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
Replace the continuously variable transaxle assembly.
Result
Proceed to
NEXT