REAR BUMPER(for Hatchback) REASSEMBLY
PROCEDURE
INSTALL REAR BUMPER ARM SUB-ASSEMBLY LH
-
Install the rear bumper arm sub-assembly LH with the 3 bolts.
11.5 N*m
117 kgf*cm
8 ft.*lbf
-
INSTALL REAR BUMPER ARM SUB-ASSEMBLY RH
Tip:Use the same procedure as for the LH side.
INSTALL NO. 1 REAR BUMPER REINFORCEMENT
-
Install the No. 1 rear bumper reinforcement with the 8 bolts.
11.5 N*m
117 kgf*cm
8 ft.*lbf
-
INSTALL REAR BUMPER SIDE SEAL LH
-
Install the rear bumper side seal LH with the 3 clips.
-
INSTALL REAR BUMPER SIDE SEAL RH
-
Install the rear bumper side seal RH with the 3 clips.
-
INSTALL UPPER REAR BUMPER RETAINER LH
-
Engage the 2 guides to temporarily install the upper rear bumper retainer LH to the rear combination light assembly LH.
-
Engage the 2 guides as shown in the illustration to temporarily install the upper rear bumper retainer LH and rear combination light assembly LH as a set.
Install the upper rear bumper retainer LH with the screw.
-
INSTALL UPPER REAR BUMPER RETAINER RH
Tip:Use the same procedure as for the LH side.
INSTALL REAR COMBINATION LIGHT ASSEMBLY LH
INSTALL REAR COMBINATION LIGHT ASSEMBLY RH
Tip:Use the same procedure as for the LH side.
INSTALL REAR BUMPER SIDE RETAINER LH
-
Engage the 3 claws.
Install the rear bumper side retainer LH with the 2 screws.
-
INSTALL REAR BUMPER SIDE RETAINER RH
Tip:Use the same procedure as for the LH side.
INSTALL REAR BUMPER MOULDING
-
Engage the 3 guides and 2 claws.
Install the rear bumper moulding with the 3 screws.
-
INSTALL REAR BUMPER SIDE MOULDING LH
-
Engage the 4 claws.
Install the rear bumper side moulding LH with the 3 screws.
-
INSTALL REAR BUMPER SIDE MOULDING RH
Tip:Use the same procedure as for the LH side.
INSTALL REAR BUMPER GUARD
-
Engage the 11 claws.
-
Install the rear bumper guard with the 4 screws.
1.5 N*m
15 kgf*cm
13 in.*lbf
-
INSTALL REFLEX REFLECTOR ASSEMBLY LH
-
Engage the claw.
Install the reflex reflector assembly LH with the screw.
-
INSTALL REFLEX REFLECTOR ASSEMBLY RH
Tip:Use the same procedure as for the LH side.
INSTALL REAR LICENSE PLATE CUSHION
Clean off any tape adhesive residue with cleaner.
Remove the release paper from 2 new license plate cushions.
Tip:After removing the release paper, keep the exposed adhesive free from foreign matter.
Install the 6 rear license plate cushions as shown in the illustration.
Tip:Stick the 6 license plate cushions on the line marked on the rear bumper assembly.
*a
Line
-
-
w/ Bracket:
Clean off any tape adhesive residue with cleaner.
Remove the release paper from 2 new license plate cushions.
Tip:After removing the release paper, keep the exposed adhesive free from foreign matter.
-
*a
Center of rear license plate cushion
Install the 2 rear license plate cushions as shown in the illustration.
Reference Measurement
Area
Measurement
A
210 mm (8.27 in.)
INSTALL LICENSE PLATE BRACKET (w/ Bracket)
-
Install the license plate bracket with the 2 screws.
-
INSTALL NO. 2 LUGGAGE ROOM WIRE (w/ TOYOTA Parking Assist-sensor System)
-
Engage the 2 clamps to install the No. 2 luggage room wire.
-
INSTALL ULTRASONIC SENSOR BEZEL (w/ TOYOTA Parking Assist-sensor System)
INSTALL ULTRASONIC SENSOR CLIP (w/ TOYOTA Parking Assist-sensor System)
INSTALL NO. 3 ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)