IMMOBILISER SYSTEM(w/o Entry and Start System) Security Indicator Light Does not Blink
| DTC Code | DTC Name |
|---|---|
| Security Indicator Light Does not Blink |
DESCRIPTION
The transponder key ECU assembly blinks the security indicator light when the immobiliser is set.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
If the transponder key ECU assembly is replaced, refer to Service Bulletin.
PROCEDURE
SYSTEM CHECK
Check the vehicle specification.
Result
Result
Proceed to
w/o Theft Deterrent System
A
w/ Theft Deterrent System
B
B PERFORM ACTIVE TEST USING GTS (SECURITY INDICATOR)Click here
PERFORM ACTIVE TEST USING GTS (SECURITY INDICATOR)
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Immobiliser / Active Test.
Perform the Active Test according to the display on the GTS.
Body Electrical > Immobiliser > Active Test
Tester Display
Measurement Item
Control Range
Diagnostic Note
Security Indicator
Security indicator light
ON/OFF
-
Body Electrical > Immobiliser > Active Test
Tester Display
Security Indicator
OK
Security indicator light can be turned on and off using the GTS.
Result
Proceed to
OK
NG
OK REPLACE TRANSPONDER KEY ECU ASSEMBLY
CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - TELLTALE LIGHT ASSEMBLY AND BODY GROUND)
Disconnect E21 transponder key ECU assembly connector.
Disconnect the E48 security indicator light (telltale light assembly) connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection
Condition
Specified Condition
E48-9 (LP) - E21-8 (IND)
Always
Below 1 Ω
E48-9 (LP) - Body ground
Always
10 kΩ or higher
E21-8 (IND) - Body ground
Always
10 kΩ or higher
E48-6 (ILL-) - Body ground
Always
Below 1 Ω
Result
Proceed to
OK
NG
NG REPAIR OR REPLACE HARNESS OR CONNECTOR
CHECK TRANSPONDER KEY ECU ASSEMBLY (TERMINAL IND)
Connect the E21 transponder key ECU assembly connector.
Measure the voltage according to the value(s) in the table below.
Standard Voltage
Tester Connection
Condition
Specified Condition
E48-9 (LP) - Body ground
Key not in ignition key cylinder
Pulse generation
Key in ignition key cylinder
Below 1 V
Result
Proceed to
OK
NG
OK REPLACE SECURITY INDICATOR LIGHT (TELLTALE LIGHT ASSEMBLY)
for Sedan:Click here
except Sedan:Click here
NG REPLACE TRANSPONDER KEY ECU ASSEMBLY
PERFORM ACTIVE TEST USING GTS (SECURITY INDICATOR)
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Immobiliser or Main Body / Active Test.
Perform the Active Test according to the display on the GTS.
Body Electrical > Immobiliser > Active Test
Tester Display
Measurement Item
Control Range
Diagnostic Note
Security Indicator
Security indicator light
ON/OFF
-
Body Electrical > Immobiliser > Active Test
Tester Display
Security Indicator
Body Electrical > Main Body > Active Test
Tester Display
Measurement Item
Control Range
Diagnostic Note
Security Indicator
Security indicator light
ON/OFF
-
Body Electrical > Main Body > Active Test
Tester Display
Security Indicator
Result
Result
Proceed to
Security indicator light operation is normal when performing the "Main Body" and "Immobiliser" Active Test
A
Security indicator light operation is not normal when performing the "Immobiliser" Active Test
Security indicator light operation is normal when performing the "Main Body" Active Test
B
Security indicator light operation is normal when performing the "Immobiliser" Active Test
Security indicator light operation is not normal when performing the "Main Body" Active Test
C
Security indicator light operation is not normal when performing the "Main Body" and "Immobiliser" Active Test
D
B CHECK HARNESS AND CONNECTOR (TELLTALE LIGHT ASSEMBLY - TRANSPONDER KEY ECU ASSEMBLY)Click here
C CHECK HARNESS AND CONNECTOR (TELLTALE LIGHT ASSEMBLY - MAIN BODY ECU)Click here
D CHECK HARNESS AND CONNECTOR (TELLTALE LIGHT ASSEMBLY - MAIN BODY ECU OR TRANSPONDER KEY ECU)Click here
CHECK SECURITY INDICATOR LIGHT (TELLTALE LIGHT ASSEMBLY) OPERATION
When the immobiliser is set, check that the security indicator light blinks.*1
OK
The security indicator light blinks normally.
When the theft deterrent system is in the arming preparation state, check that the security indicator light is on.*2
OK
The security indicator light is on.
Result
Result
Proceed to
Both *1 and *2 are OK
A
*1 is NG (*2 is OK)
B
*2 is NG (*1 is OK) (for LHD)
C
*2 is NG (*1 is OK) (for RHD)
D
Both *1 and *2 are NG
E
B REPLACE TRANSPONDER KEY ECU ASSEMBLY
E REPLACE SECURITY INDICATOR LIGHT (TELLTALE LIGHT ASSEMBLY)
for Sedan:Click here
except Sedan:Click here
CHECK HARNESS AND CONNECTOR (TELLTALE LIGHT ASSEMBLY - TRANSPONDER KEY ECU ASSEMBLY)
Disconnect the E48 security indicator light (telltale light assembly) connector.
Disconnect the E21 transponder key ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection
Condition
Specified Condition
E21-8 (IND) - E48-9 (LP)
Always
Below 1 Ω
E21-8 (IND) - Body ground
Always
10 kΩ or higher
E48-9 (LP) - Body ground
Always
10 kΩ or higher
Result
Proceed to
OK
NG
OK REPLACE TRANSPONDER KEY ECU ASSEMBLY
NG REPAIR OR REPLACE HARNESS OR CONNECTOR
CHECK HARNESS AND CONNECTOR (TELLTALE LIGHT ASSEMBLY - MAIN BODY ECU)
Disconnect the E48 security indicator light (telltale light assembly) connector.
Disconnect the E108 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection
Condition
Specified Condition
E108-22 (IND) - E48-9 (LP)
Always
Below 1 Ω
E108-22 (IND) - Body ground
Always
10 kΩ or higher
E48-9 (LP) - Body ground
Always
10 kΩ or higher
Result
Result
Proceed to
OK (for LHD)
A
OK (for RHD)
B
NG
C
C REPAIR OR REPLACE HARNESS OR CONNECTOR
CHECK HARNESS AND CONNECTOR (TELLTALE LIGHT ASSEMBLY - MAIN BODY ECU OR TRANSPONDER KEY ECU)
Disconnect the E48 security indicator light (telltale light assembly) connector.
Disconnect E21 transponder key ECU assembly connector.
Disconnect the E108 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection
Condition
Specified Condition
E21-8 (IND) - E48-9 (LP)
Always
Below 1 Ω
E108-22 (IND) - E48-9 (LP)
Always
Below 1 Ω
E21-8 (IND) - Body ground
Always
10 kΩ or higher
E48-9 (LP) - Body ground
Always
10 kΩ or higher
E48-6 (ILL-) - Body ground
Always
Below 1 Ω
Result
Proceed to
OK
NG
NG REPAIR OR REPLACE HARNESS OR CONNECTOR
REPLACE SECURITY INDICATOR LIGHT (TELLTALE LIGHT ASSEMBLY)
Temporarily replace the security indicator light (telltale light assembly) with a new or known good one.
for Sedan:Click here
except Sedan:Click here
When the immobiliser is set or theft deterrent system is in the arming preparation state, check that the security indicator light blinks.
OK
Security indicator light blinks.
Result
Proceed to
OK
NG
OK END (SECURITY INDICATOR LIGHT (TELLTALE LIGHT ASSEMBLY) WAS DEFECTIVE)
REPLACE TRANSPONDER KEY ECU ASSEMBLY
Temporarily replace the transponder key ECU assembly with a new or known good one.
Tip:Refer to Service Bulletin.
When the immobiliser is set or theft deterrent system is in the arming preparation state, check that the security indicator light blinks.
OK
Security indicator light blinks.
Result
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C
A END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)