STEERING PAD SWITCH INSPECTION

PROCEDURE

  1. INSPECT STEERING PAD SWITCH ASSEMBLY (w/ Back Switch of Steering Pad Switch Assembly)

    1. Measure the resistance according to the value(s) in the table below.

      E265405C03

      *A

      w/ Speed Limiter System

      -

      -

      *a

      Component without harness connected

      (Steering Pad Switch Assembly)

      *b

      Volume+

      *c

      Volume-

      *d

      Back

      *e

      MODE/HOLD

      *f

      Up

      *g

      Down

      *h

      Left

      *i

      Right

      *j

      Enter

      *k

      Off hook

      *l

      On hook

      *m

      Voice

      *n

      DISP

      *o

      Speed limiter

      *p

      Terminal-A

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      1 (HO) - Terminal-A

      Always

      Below 1 Ω

      11 (AU1) - 8 (EAU)

      No switch pushed

      95 to 105 kΩ

      Up switch pushed

      Below 2.5 Ω

      Down switch pushed

      313 to 345 Ω

      Volume+ switch pushed

      950 to 1050 Ω

      Volume- switch pushed

      2955 to 3265 Ω

      10 (AU2) - 8 (EAU)

      No switch pushed

      95 to 105 kΩ

      MODE/HOLD switch pushed

      Below 2.5 Ω

      On hook switch pushed

      313 to 345 Ω

      Off hook switch pushed

      950 to 1050 Ω

      Voice switch pushed

      2955 to 3265 Ω

      9 (AU3) - 8 (EAU)

      No switch pushed

      95 to 105 kΩ

      Enter switch pushed

      Below 2.5 Ω

      Back switch pushed

      313 to 345 Ω

      Right switch pushed

      950 to 1050 Ω

      Left switch pushed

      2955 to 3265 Ω

      2 (+DP) - 3 (-DP)

      No switch pushed

      10 kΩ or higher

      DISP switch pushed

      Below 2.5 Ω

      4 (ASLD) - 7 (ECC)*1

      No switch pushed

      10 kΩ or higher

      Speed limiter main switch pushed

      Below 2.5 Ω

      • *1: w/ Speed Limiter System

      Tip:

      If the result is not as specified, replace the steering pad switch assembly.

    2. Check the illumination.

      E265406C02

      *a

      Component without harness connected

      (Steering Pad Switch Assembly)

      -

      -

      1. Connect a battery positive (+) lead to terminal IL+2 and a negative (-) lead to terminal -DP of the steering pad switch assembly connector.

      2. Check that the switch illumination comes on.

        OK

        Steering pad switch illumination comes on.

        Tip:

        If the result is not as specified, replace the steering pad switch assembly.

  2. INSPECT STEERING PAD SWITCH ASSEMBLY (w/o Back Switch of Steering Pad Switch Assembly)

    1. Measure the resistance according to the value(s) in the table below.

      E262621C03

      *a

      Component without harness connected

      (Steering Pad Switch Assembly)

      *b

      Volume+

      *c

      Volume-

      *d

      Seek-

      *e

      Seek+

      *f

      MODE/HOLD

      *g

      DISP

      *h

      Terminal-A

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      1 (HO) - Terminal-A

      Always

      Below 1 Ω

      11 (AU1) - 8 (EAU)

      No switch pushed

      95 to 105 kΩ

      Seek+ switch pushed

      Below 2.5 Ω

      Seek- switch pushed

      313 to 345 Ω

      Volume+ switch pushed

      950 to 1050 Ω

      Volume- switch pushed

      2955 to 3265 Ω

      10 (AU2) - 8 (EAU)

      No switch pushed

      95 to 105 kΩ

      MODE/HOLD switch pushed

      Below 2.5 Ω

      2 (+DP) - 3 (-DP)

      No switch pushed

      10 kΩ or higher

      DISP switch pushed

      Below 2.5 Ω

      Tip:

      If the result is not as specified, replace the steering pad switch assembly.

    2. Check the illumination.

      E262622C02

      *a

      Component without harness connected

      (Steering Pad Switch Assembly)

      -

      -

      1. Connect a battery positive (+) lead to terminal IL+2 and a negative (-) lead to terminal -DP of the steering pad switch assembly connector.

      2. Check that the switch illumination comes on.

        OK

        Steering pad switch illumination comes on.

        Tip:

        If the result is not as specified, replace the steering pad switch assembly.