AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) Blower Motor Circuit

DTC Code DTC Name
Blower Motor Circuit

DESCRIPTION

The blower motor with fan sub-assembly is operated by signals from the air conditioning amplifier assembly. Blower motor speed signals are transmitted in accordance with changes in the duty ratio.

WIRING DIAGRAM

E229256E21

CAUTION / NOTICE / HINT

Note:

Inspect the fuses for circuits related to this system before performing the following procedure.

PROCEDURE

  1. PERFORM ACTIVE TEST USING GTS

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Air Conditioner / Active Test.

    5. Check the operation by referring to the table below.

      Body Electrical > Air Conditioner > Active Test

      Tester Display

      Measurement Item

      Control Range

      Diagnostic Note

      Blower Motor

      Blower motor with fan sub-assembly

      Min.: 0, Max.: 31

      -

      Body Electrical > Air Conditioner > Active Test

      Tester Display

      Blower Motor

    Result

    Result

    Proceed to

    OK

    A

    NG (Blower motor with fan sub-assembly does not operate)

    B

    NG (Blower motor with fan sub-assembly operates but does not change speed)

    C

    A

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

    C

    INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLYClick here

    B
  2. CHECK HARNESS AND CONNECTOR (BLOWER MOTOR WITH FAN SUB-ASSEMBLY - BODY GROUND)

    1. Disconnect the E13 blower motor with fan sub-assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      E13-1 (GND) - Body ground

      Always

      Below 1 Ω

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK
  3. CHECK HARNESS AND CONNECTOR (BLOWER MOTOR WITH FAN SUB-ASSEMBLY - BATTERY)

    1. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Condition

      Specified Condition

      E13-3 (+B) - Body ground

      Always

      11 to 14 V

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK
  4. CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - BLOWER MOTOR WITH FAN SUB-ASSEMBLY)

    1. Disconnect the E28 air conditioning amplifier assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      E28-22 (BLW) - E13-2 (SI)

      Always

      Below 1 Ω

      E28-22 (BLW) - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK
  5. INSPECT BLOWER MOTOR WITH FAN SUB-ASSEMBLY

    1. Reconnect the E13 blower motor with fan sub-assembly connector.

    2. E221028C08

      *a

      Front view of wire harness connector

      (to Air Conditioning Amplifier Assembly)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Condition

      Specified Condition

      E28-22 (BLW) - Body ground

      Always

      4.5 to 5.5 V

    Result

    Proceed to

    OK

    NG

    NG

    REPLACE BLOWER MOTOR WITH FAN SUB-ASSEMBLY

    OK
  6. INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY

    1. Reconnect the E28 air conditioning amplifier assembly connector.

    2. Turn the ignition switch to ON.

    3. Turn the blower switch on (LO).

    4. E230728C04

      *a

      Component with harness connected

      (Air Conditioning Amplifier Assembly)

      Measure the waveform between terminal E28-22 (BLW) of the air conditioning amplifier assembly and body ground.

      OK

      Waveform is similar to that shown in the illustration.

      Tip:

      The waveform varies with the blower speed.

      Item

      Content

      Tool setting

      1 V/DIV., 500 μs/DIV.

      Vehicle condition

      Ignition switch ON

      Blower switch: LO

    Result

    Proceed to

    OK

    NG

    OK

    REPLACE BLOWER MOTOR WITH FAN SUB-ASSEMBLY

    NG

    REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY