VEHICLE STABILITY CONTROL SYSTEM, Diagnostic DTC:C1441

DTC Code DTC Name
C1441 Performance Decline of Brake Function

DESCRIPTION

The skid control ECU (brake actuator assembly) judges brake failure conditions have occurred based on signals from the brake pedal load sensing switch and master cylinder pressure sensor. (for 1AD-FTV)

Note:

Do not intentionally stop the engine when driving. Even when no malfunction has occurred in the brake system, DTC C1441 will be stored when it is judged that a failure has occurred in the brake system due to a reduction in vacuum.

  • DTCs may be stored if one of the following occurs:

  • The brake pedal load sensing switch is malfunctioning (deviation in characteristics).

  • The brake pedal is depressed when moving the vehicle with the engine not running and the ignition switch to ON.

  • Bleeding is performed with the engine running or the ignition switch to ON.

  • The accelerator and brake pedals are depressed simultaneously.*

Tip:

*: The skid control ECU (brake actuator assembly) may store this DTC upon judging that a stuck on malfunction has occurred when the accelerator pedal and brake pedal are depressed simultaneously. However, this does not indicate a malfunction.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

C1441

Performance Decline of Brake Function

When the brake pedal load sensing switch and master cylinder pressure sensor are functioning normally and the brake pedal load sensing switch is judged as on, the pressure signal from the master cylinder pressure sensor does not indicate an increase.

  • Brake pedal load sensing switch (brake Pedal Support Assembly)

  • Brake booster assembly

  • Skid control ECU (brake actuator assembly)

  • Brake fluid leaks

CAUTION / NOTICE / HINT

Note:

When replacing the skid control ECU (brake actuator assembly), perform system variant learning.

Click here

PROCEDURE

  1. CHECK ACCELERATOR PEDAL AND BRAKE PEDAL OPERATION

    1. Interview the customer to check if the pedals were depressed simultaneously while driving or braking.

      OK

      The pedals were not depressed simultaneously.

      Tip:

      The skid control ECU (brake actuator assembly) may store this DTC upon judging that a stuck on malfunction has occurred when the accelerator pedal and brake pedal are depressed simultaneously. If the pedals were depressed simultaneously, clear the DTC because it is not a malfunction.

    Result

    Proceed to

    OK

    NG

    NG

    END

    OK
  2. CHECK DTC AND FREEZE FRAME DATA

    1. Check and record DTCs and Freeze Frame Data.

      for Check DTCs:Click here

      for Freeze Frame Data:Click here

      Chassis > ABS/VSC/TRC > Trouble Codes

      Tip:
      • Read Freeze Frame Data at the time DTC C1441 was stored, go to operation history and confirm the operating conditions.

      • When reading Freeze Frame Data to confirm operating conditions, the following items can be confirmed: "F# or R# Wheel Speed", "Vehicle Speed", "Real Engine Torque" and "Accelerator Opening Angle %".

    Result

    Proceed to

    NEXT

    NEXT
  3. CLEAR DTC

    1. Clear the DTCs and Freeze Frame Data.

      for Clear DTCs:Click here

      for Freeze Frame Data:Click here

      Chassis > ABS/VSC/TRC > Clear DTCs

      Result

      Proceed to

      NEXT

    NEXT
  4. CHECK BRAKE PEDAL OPERATION

    1. Based on the customer problem analysis, confirm the brake pedal condition at the time the brake pedal was operated.

      Result

      Result

      Proceed to

      The brake pedal is hard to depress.

      A

      The brake pedal is extremely easy to depress.

      B

      Neither of the above conditions. (Problem symptom does not occur.)

      C

    B

    INSPECT BRAKE SYSTEMClick here

    C

    RECONFIRM DTCClick here

    A
  5. CHECK BRAKE BOOSTER ASSEMBLY

    1. Check the brake booster assembly.

      for LHD:Click here

      for RHD:Click here

      Result

      Result

      Proceed to

      The brake booster assembly is abnormal.

      A

      The brake booster assembly is normal.

      B

      Tip:

      If the result shows that the brake booster assembly is defective, check the related components such as the brake booster, brake vacuum check valve, check valve grommet, brake booster gasket, vacuum hose and intake system for vacuum leaks or clogs.

    A

    INSPECT RELATED COMPONENTS (FOR VACUUM LEAKS OR CLOGS)

    B

    RECONFIRM DTCClick here

  6. INSPECT BRAKE SYSTEM

    1. Brake pedal inspection

      1. Perform a visual inspection and operate the brake pedal to check for any malfunctions.

      2. Check the brake pedal height, brake pedal free play and brake pedal reserve distance.

        for LHD:Click hereClick here

        for RHD:Click hereClick here

        Tip:

        If the brake pedal height is not within specification, confirm that there are no other malfunctions before adjusting the brake pedal height.

    2. Brake inspection

      1. Check that the disc brake pads of each wheel are installed correctly.

      2. Check that the bleeder plug and union bolt is not loose, and that there are no damaged gaskets or brake fluid leaks, for each wheel cylinder.

    3. Brake fluid leaks and air in brake line inspection

      1. Check and take a note of the fluid level in the brake master cylinder reservoir assembly.

      2. Repeatedly depress the brake pedal and confirm that the brake pedal feels normal (no air in the system, etc.).

      3. Check if the brake fluid level in the brake master cylinder reservoir assembly has changed.

      4. If the brake fluid level has decreased, check for leaks due to damaged brake lines or hoses, loose union nuts, damaged brake master cylinder sub-assembly seals, etc.

    4. Bleeding air from brake system

      1. Bleed air from the brake lines and brake actuator assembly.

        Click here

    Result

    Proceed to

    NEXT

    NEXT
  7. PERFORM ACTIVE TEST USING GTS (ABS MOTOR RELAY)

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Select the Active Test using the GTS.

      Click here

      Chassis > ABS/VSC/TRC > Active Test

      Tester Display

      Measurement Item

      Control Range

      Diagnostic Note

      Motor Relay

      ABS motor relay

      Relay ON/OFF

      Operating sound of motor can be heard

      Chassis > ABS/VSC/TRC > Active Test

      Tester Display

      Motor Relay

    4. Fully depress and hold the brake pedal.

      Tip:

      Make sure that the brake pedal has travelled excessively before holding it depressed.

    5. Operate the ABS motor relay using the Active Test and check if the brake pedal height changes when the pump motor is operating.

      OK

      The brake pedal height does not change (the brake pedal travel remains excessive).

    Result

    Proceed to

    OK

    NG

    NG

    REPLACE BRAKE ACTUATOR ASSEMBLY

    OK
  8. CHECK BRAKE MASTER CYLINDER SUB-ASSEMBLY

    1. Check that there are no brake fluid leaks and no indications of a malfunction in the brake master cylinder sub-assembly.

      OK

      There are no brake fluid leaks and no indications of a malfunction in the brake master cylinder sub-assembly.

    Result

    Proceed to

    OK

    NG

    NG

    REPLACE BRAKE MASTER CYLINDER SUB-ASSEMBLY

    OK
  9. INSPECT BRAKE BOOSTER ASSEMBLY

    1. Inspect operation of the brake booster assembly.

      for LHD:Click here

      for RHD:Click here

      OK

      The brake booster assembly is normal.

    Result

    Proceed to

    OK

    NG

    OK

    RECONFIRM DTCClick here

    NG

    REPLACE BRAKE BOOSTER ASSEMBLY

  10. RECONFIRM DTC

    1. Clear the DTCs.

      Click here

      Chassis > ABS/VSC/TRC > Clear DTCs

    2. Start the engine.

    3. Perform a road test.

      Note:

      Do not intentionally stop the engine when driving. DTC C1441 will be stored if the brake pedal is depressed when moving the vehicle with the engine not running and the ignition switch ON.

    4. Check if the same DTC is recorded.

      Click here

      Chassis > ABS/VSC/TRC > Trouble Codes

      Result

      Result

      Proceed to

      DTC C1441 is not output.

      A

      DTC C1441 and other DTCs are output.

      B

      Only DTC C1441 is output.

      C

      Tip:
      • If DTC C1441 and other DTCs are output simultaneously, the other DTCs may have caused the engine to malfunction, resulting in DTC C1441 to be output. Read Freeze Frame Data to confirm malfunctioning parts and repair the applicable part.

      • When reading Freeze Frame Data to confirm malfunctioning parts, the following items can be confirmed: "F# or R# Wheel Speed", "Vehicle Speed", "Real Engine Torque" and "Accelerator Opening Angle %".

    A

    END

    B

    CHECK AND REPAIR APPLICABLE PART

    C
  11. CHECK BRAKE PEDAL SUPPORT ASSEMBLY

    C272256C01

    *1

    Brake Pedal Support Assembly

    *2

    Brake Pedal Load Sensing Switch

    *a

    Matchmark

    1. Check that the matchmarks on the adjustment part of the brake pedal load sensing switch are aligned with the matchmarks on the brackets, nuts, adjusting screw, etc.

      OK

      The matchmarks on the adjustment part of the brake pedal load sensing switch are aligned with the matchmarks on the brackets, nuts, adjusting screw, etc.

      Result

      Proceed to

      OK

      NG

    OK

    REPLACE BRAKE ACTUATOR ASSEMBLY

    NG

    REPLACE BRAKE PEDAL SUPPORT ASSEMBLY

    for LHD:Click here

    for RHD:Click here