FIT STANDARD / ADJUSTMENT METHOD ADJUSTMENT


  1. INSPECT HOOD SUB-ASSEMBLY


    1. Check that the clearance measurements of areas A to G are within the standard range.

      A002KYHE01

      Tech Tips

      Centering bolts are used to mount the hood hinge and hood lock. The hood and hood lock cannot be adjusted with the centering bolts on. Substitute the centering bolts with standard bolts when making adjustments.

    2. ADJUST HOOD SUB-ASSEMBLY


      1. A002KVQ

        Adjust the hood position.


        1. Loosen the 4 hinge bolts of the hood.

        2. Move the hood and adjust the clearance between the hood and front fender.

        3. Tighten the 4 hinge bolts of the hood after the adjustment.

          Torque:
          13 N*m  { 133 kgf*cm, 10 ft.*lbf }
        4. A002KXS

          Adjust the cushion rubber so that the height of the hood and fender are aligned.

          Tech Tips

          Raise or lower the front end of the hood by turning the cushion rubber.

      2. Adjust the hood lock.


        1. Remove the upper radiator support seal.

        2. Remove the lower No. 1 radiator mounting bracket.

        3. A002KUC

          Loosen the 2 bolts and hood lock nut.

        4. Adjust the hood lock position so that the striker can enter it smoothly.

        5. Tighten the bolts and nut after the adjustment.

          Torque:
          5.5 N*m  { 56 kgf*cm, 49 in.*lbf }
        6. Install the lower No. 1 radiator mounting bracket.

        7. Install the upper radiator support seal.

    3. INSPECT FRONT DOOR


      1. Check that the clearance measurements of areas A to O are within the standard range.

        A002KW9E03
    4. Tech Tips


      • Before adjusting the door position for vehicles equipped with side airbags and curtain shield airbags, be sure to disconnect the cable from the negative (-) battery terminal.

      • Use the same procedures for the RH side and LH side.

      • The procedures listed below are for the LH side.

      • Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts on. Substitute the centering bolts with standard bolts when making adjustments.

    5. ADJUST FRONT DOOR


      1. Remove the upper radiator support seal.

      2. A002KXH

        Disconnect the cable from the negative (-) battery terminal.

        CAUTION:

        Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

        Note

        When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

      3. Using SST, loosen the body hinge bolts and adjust the door position.

        SST
        09812-00010
      4. Using SST, tighten the body hinge bolts after the adjustment.

        Torque:
        26 N*m  { 265 kgf*cm, 19 ft.*lbf }
      5. Loosen the door hinge bolts and adjust the door position.

      6. Tighten the door hinge bolts after the adjustment.

        Torque:
        26 N*m  { 265 kgf*cm, 19 ft.*lbf }
      7. A002KRI

        Using a screwdriver, detach the 4 claws and remove the cover.

        Tech Tips

        Tape the screwdriver tip before use.

      8. A002KWZ

        Using a T40 "TORX" socket, adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a plastic-faced hammer.

      9. Using a T40 "TORX" socket, tighten the striker mounting screws after the adjustment.

        Torque:
        23 N*m  { 235 kgf*cm, 17 ft.*lbf }
      10. Attach the 4 claws to install the cover.

      11. Connect the cable to the negative (-) battery terminal.

        Note

        When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

      12. Check the SRS warning light.

      13. Install the upper radiator support seal.

    6. INSPECT REAR DOOR


      1. Check that the clearance measurements of areas A to M are within the standard range.

        A002KSPE01
    7. Tech Tips


      • Before adjusting the door position for vehicles equipped with side airbags and curtain shield airbags, be sure to disconnect the cable from the negative (-) battery terminal.

      • Use the same procedures for the RH side and LH side.

      • The procedures listed below are for the LH side.

      • Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts on. Substitute the centering bolts with standard bolts when making adjustments.

    8. ADJUST REAR DOOR

      A002KV9

      1. Loosen the body hinge bolts and adjust the door position.

        SST
        09812-00010
      2. Tighten the body hinge bolts after the adjustment.

        Torque:
        26 N*m  { 265 kgf*cm, 19 ft.*lbf }
      3. Loosen the door hinge bolts and adjust the door position.

      4. Tighten the door hinge bolts after the adjustment.

        Torque:
        26 N*m  { 265 kgf*cm, 19 ft.*lbf }
      5. A002KR1

        Using a screwdriver, detach the 4 claws and remove the cover.

        Tech Tips

        Tape the screwdriver tip before use.

      6. A002KRQ

        Using a T40 "TORX" socket, adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a plastic-faced hammer.

      7. Using a T40 "TORX" socket, tighten the striker mounting screws after the adjustment.

        Torque:
        23 N*m  { 235 kgf*cm, 17 ft.*lbf }
      8. Attach the 4 claws to install the cover.

    9. INSPECT TAIL GATE PANEL SUB-ASSEMBLY


      1. Check that the clearance measurements of area A to B are within the standard range.

        A002KWPE02
    10. ADJUST TAIL GATE PANEL SUB-ASSEMBLY


      1. Loosen the hinge bolts.

      2. A002KYC

        Adjust the tail gate by moving it up and down and left and right so that the dimensions are within the specified range.

      3. Tighten the hinge bolts.

        Torque:
        28 N*m  { 286 kgf*cm, 21 ft.*lbf }
      4. A002KYL

        Loosen the hinge bolts.

      5. Adjust the tail gate by moving it up and down and forward and backward so that the dimensions are within the specified range.

      6. Tighten the hinge bolts.

        Torque:
        31 N*m  { 316 kgf*cm, 23 ft.*lbf }
    11. ADJUST DOOR LOCK STRIKER


      1. A002KRD

        Using a T40 "TORX" socket, adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a plastic-faced hammer.

      2. Using a T40 "TORX" socket, tighten the striker mounting screws after the adjustment.

        Torque:
        23 N*m  { 235 kgf*cm, 17 ft.*lbf }
    12. ADJUST REAR SWING GATE LOCK STRIKER


      1. A002KRL

        Check that the door fit and door linkages are adjusted correctly.

      2. Using a T40 "TORX" socket, adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a plastic-faced hammer.

      3. Using a T40 "TORX" socket, tighten the striker mounting screws after the adjustment.

        Torque:
        23 N*m  { 235 kgf*cm, 17 ft.*lbf }
    13. INSPECT BACK DOOR PANEL SUB-ASSEMBLY


      1. Check that the clearance measurements of areas A to F are within the standard range.

        A002KRWE03
    14. ADJUST REAR SWING GATE LOCK STRIKER


      1. A002KRL

        Check that the door fit and door linkages are adjusted correctly.

      2. Using a T40 "TORX" socket, adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a plastic-faced hammer.

      3. Using a T40 "TORX" socket, tighten the striker mounting screws after the adjustment.

        Torque:
        23 N*m  { 235 kgf*cm, 17 ft.*lbf }
    15. ADJUST BACK DOOR PANEL SUB-ASSEMBLY


      1. A002KR8

        Loosen the hinge bolts.

      2. Adjust the back door by moving it up and down and left and right so that the dimensions are within the specified range.

      3. Tighten the hinge bolts.

        Torque:
        19 N*m  { 194 kgf*cm, 14 ft.*lbf }
      4. Detach the seat belt anchor cover.

      5. A002KUM

        Loosen the hinge nuts.

      6. Adjust the back door by moving it up and down and forward and backward so that the dimensions are within the specified range.

      7. Tighten the hinge nuts.

        Torque:
        19 N*m  { 194 kgf*cm, 14 ft.*lbf }
      8. Attach the seat belt anchor cover.