WHEN REMOVING,INSTALLING,REPAIRING OR REPLACING PARTS PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED

Refer to the LEXUS Repair Manual for each inspection procedure.


  1. PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED

    Replacement Part Necessary Procedure Effect / Inoperative Function when Necessary Procedures are not Performed Note
    Power management control ECU ECU communication ID registration (Immobiliser system) Hybrid control system start See the Service Bulletin for the registration method.

    • Throttle body with motor assembly

    • Cleaning the deposits from the throttle body with motor assembly

    • Engine assembly

    • Cylinder head sub-assembly

    • Camshaft (for intake or exhaust camshaft)

    • Camshaft timing gear assembly

    • Piston or piston ring

    • Mass air flow meter sub-assembly

    • Fuel injector assembly

    • Fuel pump

    • Air fuel ratio sensor

    • Engine coolant temperature sensor

    • Spark plug

    • Ignition coil assembly

    • Air leaks from intake system

    • Gas leaks from exhaust system

    • Knock control sensor

    Inspection after repair Poor idle, engine starting, etc -
    Millimeter wave radar sensor assembly Adjust millimeter wave radar sensor assembly
    • Dynamic radar cruise control system

    • Pre-crash safety system

    -
    Lane departure warning camera Adjust lane departure warning camera Lane departure alert system -

    • Tire pressure warning ECU and receiver

    • Tire pressure warning valve and transmitter


    • Transmitter ID registration

    • Initialization


    • When DTC detection conditions of "transmitter ID not received" DTC are met, TPWS indicator blinks for 1 minute, and then illuminates.

    • Tire pressure warning function

    -
    Brake booster with master cylinder assembly
    • Perform initialization and calibration of the linear solenoid valve

    • Perform yaw rate and acceleration sensor zero point calibration


    • ABS warning light illumination

    • Brake warning light/yellow (minor malfunction) illumination

    • Slip indicator light illumination

    • VSC disable or malfunctioning

    -

    • Brake pedal stroke sensor assembly

    • Brake pedal


    • Clear stored linear solenoid valve calibration data

    • Perform initialization and calibration of the linear solenoid valve

    -
    Yaw rate and acceleration sensor (Airbag sensor assembly)
    • Clear zero point calibration data

    • Perform yaw rate and acceleration sensor zero point calibration

    -
    Power steering ECU assembly
    • Torque sensor zero point calibration

    • Assist map writing


    • EPS warning light comes on

    • EPS control

    -
    Electric power steering column sub-assembly Torque sensor zero point calibration Steering effort is different between turning steering wheel to left and right
    Spiral cable with sensor sub-assembly
    • Steering angle neutral point (Initialize parking assist monitor system)

    • Steering angle setting

    Parking assist monitor system -

    • Rear television camera assembly

    • Suspension, tires, etc (the vehicle height changes because of suspension or tires replacement)

    Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system
    Multi-media module receiver assembly Parking assist monitor system initialization Parking assist monitor system
    Telematics transceiver Vehicle contract setting
    • G-BOOK service

    • Emergency call service

    -
    Blind spot monitor sensor Blind spot monitor beam axis inspection DTCs are output -

    • Certification ECU (smart key ECU assembly)

    • ID code box (immobiliser code ECU)

    • Main body ECU (multiplex network body ECU)

    • Steering lock ECU (steering lock actuator assembly)

    • Electrical key transmitter sub-assembly

    Code registration (Immobiliser system)
    • Wireless door lock control system

    • Smart entry and start system

    • Hybrid control system start

    • Steering lock system

    See the Service Bulletin for the registration method.

    • No. 1 air conditioning radiator damper servo sub-assembly

    • No. 2 air conditioning radiator damper servo sub-assembly

    • No. 3 air conditioning radiator damper servo sub-assembly*1

    • No. 1 blower damper servo sub-assembly

    Initialization servo motor (Air conditioning system) DTCs are output -

    • Power window regulator motor assembly

    • Door window regulator assembly

    • Door glass

    • Door glass run

    Initialize power window control system
    • Auto up/down function

    • Jam protection function

    • Operation function after power switch is turned off

    • Key-linked function

    • Wireless transmitter-linked function

    • Window open warning

    -

    • Sliding roof ECU (sliding roof drive gear sub-assembly)

    • Sliding roof glass sub-assembly

    • Sliding roof drive cable sub-assembly

    Initialize sliding roof ECU (pulse sensor initial position setting)
    • Automatic slide open/close and tilt up/down function of sliding roof

    • Jam protection function

    • Operation function after power switch is turned off

    • Key-linked function

    • Wireless transmitter-linked function

    • Sliding roof open warning

    -

    • Luggage closer motor assembly

    • Luggage door closer assembly

    Check power trunk lid function Power trunk lid system -

    • Headlight leveling ECU assembly

    • Rear height control sensor sub-assembly

    Perform headlight leveling ECU assembly initialization Headlight leveling function -

    • *1: for 3 Zone Type