FRONT CONSOLE BOX REMOVAL

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. REMOVE DOOR SCUFF PLATE ASSEMBLY RH (for RHD)

    Click here

  2. REMOVE COWL SIDE TRIM BOARD RH (for RHD)

    Click here

  3. REMOVE CONSOLE ARMREST ASSEMBLY

    Click here

  4. REMOVE UPPER REAR CONSOLE PANEL

    Click here

  5. REMOVE UPPER NO. 2 CONSOLE PANEL GARNISH

    Click here

  6. REMOVE UPPER NO. 1 CONSOLE PANEL GARNISH

    Click here

  7. REMOVE INSTRUMENT SIDE PANEL LH

    Click here

  8. REMOVE NO. 1 INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

    Click here

  9. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

    Click here

  10. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

    Click here

  11. REMOVE NO. 1 SWITCH HOLE BASE

    Click here

  12. REMOVE INSTRUMENT SIDE PANEL RH

    Click here

  13. REMOVE NO. 2 INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

    Click here

  14. REMOVE INSTRUMENT PANEL FINISH PLATE

    Click here

  15. REMOVE MULTI-DISPLAY ASSEMBLY WITH BRACKET

    Click here

  16. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

    Click here

  17. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY


    1. B002IZAC01
      *1 Shifting Hole Cover Sub-assembly

      Hold the shift lever knob sub-assembly and shifting hole cover sub-assembly, and then pull down the shifting hole cover sub-assembly to detach the 2 claws.

    2. B002J20

      Twist the shift lever knob sub-assembly in the direction indicated by the arrow and remove it.

  18. REMOVE UPPER REAR CONSOLE PANEL SUB-ASSEMBLY


    1. B002IG5

      Place your hand as shown in the illustration and detach the 4 claws and 8 clips.

    2. Disconnect the connectors and detach the clamp and remove the upper rear console panel sub-assembly.

  19. REMOVE INNER NO. 1 INSTRUMENT PANEL BRACE COVER LH


    1. B002K6XC03
      B002JLO Protective Tape

      for LHD:


      1. Put protective tape around the inner No. 1 instrument panel brace cover LH.

      2. Detach the 2 clips and guide and remove the inner No. 1 instrument panel brace cover LH.

    2. B002JA9C03
      B002JLO Protective Tape

      for RHD:


      1. Put protective tape around the inner No. 1 instrument panel brace cover LH.

      2. Detach the 2 clips and guide and remove the inner No. 1 instrument panel brace cover LH.

  20. REMOVE INNER NO. 1 INSTRUMENT PANEL BRACE COVER RH


    1. B002IUUC03
      B002JLO Protective Tape

      for LHD:


      1. Put protective tape around the inner No. 1 instrument panel brace cover RH.

      2. Detach the 2 clips and guide and remove the inner No. 1 instrument panel brace cover RH.

    2. B002JZMC03
      B002JLO Protective Tape

      for RHD:


      1. Put protective tape around the inner No. 1 instrument panel brace cover RH.

      2. Detach the 2 clips and guide and remove the inner No. 1 instrument panel brace cover RH.

  21. REMOVE REAR CONSOLE END PANEL SUB-ASSEMBLY


    1. B002KHBC05
      B002JLO Protective Tape

      Put protective tape around the rear console end panel sub-assembly.

    2. Using moulding remover B, detach the 8 clips and 3 claws.

    3. Disconnect the connectors and remove the rear console end panel sub-assembly.

  22. REMOVE CONSOLE BOX POCKET (w/o Wireless Charger)


    1. B002K48

      Remove the console box pocket.

  23. REMOVE CONSOLE BOX CARPET


    1. B002KM5

      Remove the console box carpet.

  24. REMOVE CONSOLE BOX ASSEMBLY


    1. Disconnect the connectors and detach the clamps.

    2. Remove the 6 bolts.

    3. Detach the 4 guides and remove the console box assembly.

      B002KQ4C05
      *a Connector *b Clamp
      *c Bolt *d Guide